Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Welby
Gate repair in Welby usually means one of three things: a gate that won’t open, a gate that won’t close, or a gate that drags against the asphalt every single time. Most of the gates we see in this unincorporated Adams County community are original to homes built between the 1950s and 1970s, and they’re tired. Hal Gatewood has been fixing gates since 2001, and the person who answers when you call (877) 610-2993 is a live person, any hour. We don’t route calls to a faceless queue, and we don’t send someone who’s never seen a frost-heaved post footing. We serve the entire 80221 corridor, and we know exactly how Welby gates fail.
Why Gatewood Fence & Gate Is Welby’s Preferred Gate Repair Company
Hal Gatewood’s name is on the shop, the invoice, and the work. That’s not branding. It’s the accountability that comes from living where you work and knowing that the customer you see at the grocery store on Saturday is the same customer whose gate you fixed on Tuesday. Welby homeowners don’t need a company that treats their gate like a line item. They need someone who has seen what decades of Front Range freeze-thaw cycles do to a 1970s tubular-steel swing gate. That’s us.
We’re not new to the 80221. We’ve pulled gate posts on Federal Boulevard, rebuilt hinges on residential lots east of the railroad tracks, and rewired openers on homes that sit in that odd half-light half-residential interface along Globeville Road. The work here is different from Denver proper because the codes are different. We’ll get to that. What matters up front: one call brings a real person, a straight price before any work starts, and a 90-Day Done Right Promise in writing. If it’s not right, Hal makes it right. No runaround.
Our Gate Repair Services in Welby
We repair more than we replace. That’s the whole point of a Gate Repair team that welds on site instead of hauling your gate to a shop three counties away. We work on electric operators, manual swing gates, heavy sliding gates, and the hardware that quietly gives out after thirty-plus years of use. Here are the services Welby calls us about most.
Electric Gate Repair
When a gate opener dies during a cold snap, the usual culprit in Welby is an obsolete control board. Homes built in the 1950s through 1970s often still run original or early-generation operators, and those boards do not like temperature swings. We diagnose on site, and if the board is gone, we tell you plainly whether it’s worth repairing or smarter to retrofit a current operator. Every fix we recommend comes with the 90-Day Done Right Promise, and the price is set before we touch a wire.
Automatic Gate Repair
Automatic gates in Welby sit in an odd regulatory zone. We’ll explain that below, but in practical terms it means the work has to be done to Adams County electrical and entrapment-safety standards, not whatever the last guy felt like doing. We test the safety photocell, the reversing edge, and the limit switches on every automatic gate job. A gate that closes on a vehicle because the sensor was bypassed is a liability, and we see bypassed sensors in older Welby installs more than anywhere else we work. We fix them properly.
Hinge & Post Repair
This is the core of what we do in Welby. The freeze-thaw cycle at 5,200 feet of elevation heaves concrete footings out of plumb. A post that moved three inches in 1985 is now leaning six, and the gate scrapes. You can’t fix the panel if the post is moving. We cut and refit hinge barrels, reset posts to county depth, and when the original post is far enough gone, we fabricate and weld a new one that will outlast the last one by decades. Hal does the welding in your driveway.
We serve the whole Welby area, and when we say we’ll be there in the window we promised, we mean it. No call-center dance.
Gate Realignment
A sagging gate almost always means a post that walked. We realign gates at the hinge post, not in the middle of the panel. On a 1970s tubular-steel swing gate, that usually means cutting the old hinges off, shimming or replacing the post, and re-hanging the gate so the latch actually lines up without being lifted. Sometimes the gate itself is fine and only needs new bushings and a reset angle. Other times the post is beyond saving and replacement is the cheaper long-term answer. We will tell you which, and the free second opinion on any written estimate means you can verify what we say.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Welby
We service nine major gate opener brands, but the ones we see most on Welby’s older gates are Viking, Ghost Controls, DoorKing, and Elite. We stock common control boards, remotes, and safety sensors for these on the truck, so a lot of Welby jobs are finished the same visit. When a board is obsolete and no longer manufactured, we know which retrofit works without rewiring your entire gate system, and we price it before we start. We’re certified to work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so whatever your existing opener is, we’re not guessing.
Common Gate Repair Problems We See in Welby Homes
- Obsolete control boards that fail in cold snaps. The first hard freeze of the season leaves a lot of Welby automatic gates stuck mid-cycle. A board that works at 50 degrees may not fire at 5 degrees. We diagnose whether it’s the board, the capacitor, or the wiring, and replace only what’s dead.
- Frost-heaved hinge posts. Decades of freeze-thaw cycles on older concrete footings tilt posts out of plumb. The gate drags, the latch bends, and the hinges fail from fighting the angle. We reset posts to Adams County depth and rehang the gate so it swings like it did in 1972.
- Chinook wind damage. Unsupported swing gates on Welby lots get slammed against stops during high-velocity downslope winds, especially in late fall and early spring. The hinges strip and the welds crack. We weld on site, and if we spec a drop bar or a more robust stop, we’ll say why.
- Worn hinges and latch hardware from mixed residential-commercial use. Properties along the Federal Boulevard and Globeville Road edges see delivery trucks and daily home traffic through the same gate. Residential hardware fails fast under that load. We spec commercial-grade hinges and latches on these properties even when the gate looks like a simple home driveway gate, because it isn’t.
Pricing for Gate Repair in Welby, CO
What should you expect to pay for gate repair in Welby? A hinge replacement on a single swing gate typically runs $180 to $320 including hardware. Post resetting and refooting in the freeze-thawed soil of the 80221 corridor runs $400 to $900 depending on whether we pour a new concrete footing or can stabilize the existing one. Replacing an obsolete control board on an automatic operator runs $250 to $650 installed, and if you’re on a mixed-use Federals Boulevard property, we generally recommend a commercial-grade board and safety package, which pushes the top of that range. Every job carries a written 90-Day Done Right Promise, $40 off any repair over $200, and no trip charge inside the county. Seniors and veterans get a permanent 10% discount. The price is quoted and agreed before any work starts. Period. Call (877) 610-2993 for an exact quote, and remember the estimate is free.
We Also Serve Cities Near Welby
If you’re just outside the 80221, we cover the nearby cities of Federal Heights, Sherrelwood, Shaw Heights, and Westminster. The same live-answer phone, the same on-site welding, and the same written promise apply across the north metro area. If you’re on the edge of one of these borders, just call and ask; we’ll tell you straight whether we can get to you, and when.
Serving Welby, CO - Our Local Coverage Area
We’re based in the Welby area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Welby
Yes, in many cases. Because Welby is unincorporated Adams County, any gate work involving structural footings or electric operators falls under Adams County Land Development codes and permitting, not Denver’s, even for gates installed decades ago. A simple hinge replacement or realignment usually doesn’t need a permit. But resetting a post, pouring a new footing, or wiring a new automatic operator typically does. This is the single biggest way contractors working just south of the Denver line get it wrong in Welby. We know which work requires what, we handle the permitting side for you, and we won’t tell you something is “no big deal” just because the last guy skipped it. Call (877) 610-2993 and we’ll tell you exactly what your gate needs.
Usually it can be retrofitted, and that saves you money. The sag on a 1970s tubular-steel swing gate almost always comes from the hinge post leaning, not from the panel itself bending. We reset the post, refit or replace the hinge barrels, and rehang the gate. If the post is too far gone, replacement of the post alone is still cheaper than a whole new gate. If the panel is rusted through at the hinge welds, we weld on reinforcing plates and repair the rust rather than scrapping a gate with another 40 years left in it. The free second opinion on any written estimate means you can get it double-checked before spending a dollar.
Current code requires a working safety photocell across the gate opening and a reversing edge or other contact-sensing device on the gate itself, wired so that the gate reverses if something is in the way. Many older Welby automatic gates were installed before those rules, and some have had the sensors bypassed by someone who got tired of false trips. The test is simple: block the photocell’s beam with a box while the gate is closing. The gate must reverse. If it doesn’t, the system is not code-compliant and is dangerous. We test every automatic gate we work on and show you exactly what we find. Call (877) 610-2993 for a safety check and an honest fix.
No, not with its original hardware. The properties along the Federal Boulevard and Globeville Road corridors straddle the residential-light-industrial edge, and their gates see a mix of daily home use and periodic delivery truck traffic. Original residential hinges, latch posts, and roller assemblies wear out fast under that load. We spec commercial-grade hinges, heavy-duty latch brackets, and often a strengthened gate frame on these properties. It might look like a simple home driveway gate, but the loads are commercial. We’ll tell you what’s needed and price it before any work starts.
That’s the classic signature of an aging control board or capacitor that’s losing tolerance in cold weather. Older boards on 1970s-era automatic gates in Welby often work fine at 40 degrees and refuse to fire at 10 degrees. We can test the board and capacitor on site. If it’s the capacitor, the fix is quick and inexpensive. If it’s the board and the board is obsolete, we’ll lay out your retrofit options with exact prices. Don’t wait for the next deep freeze. Call (877) 610-2993 and we’ll diagnose it before you’re stuck outside again.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, fixing gates for homeowners in and around Welby, Colorado since 2001.