Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Temple City
Gate repair in Temple City usually means one of three things: a hinge anchor has pulled out of an old CMU block wall, a swing gate has drifted out of alignment in the summer heat, or a slide gate track on a rear alley is packed with debris and chewing up rollers. We fix all three, usually the same day we hear about them. Hal Gatewood has been doing this since 2001, and the person who answers when you call (877) 610-2993 is a live person, not a phone tree. If you’re in the 91780 zip code and your gate won’t close, won’t open, or sounds like it’s grinding itself to death, call us before it gets worse.
Why Gatewood Fence & Gate Is Temple City’s Preferred Gate Repair Company
Temple City is the kind of place where people still ask their neighbors who fixed their fence. We’re not a national chain with a rotating cast of subcontractors. Hal’s name is on the shop, his license number is published, and the person who shows up to your house is the same person you’ll see at the hardware store. That’s the whole model.
We’ve worked on gates along Las Tunas Drive, through the ranch-home streets north of Live Oak Park, and along the rear alleys that run behind the older tracts. Temple City customers tend to know exactly what they want repaired because they’ve usually watched it fail slowly for six months first. By the time we get there, they want a straight answer: fix it or replace it, and how much. That’s what we give them.
Every job we do in Temple City carries the 90-Day Done Right Promise in writing. If it isn’t right, one call brings Hal back. No runaround, no “that’s not covered.” We also answer the phone 24/7 with a live person, and there’s no trip charge inside the county. Those two things alone solve most of the frustration people have with gate repair companies.
Our Gate Repair Services in Temple City
Electric Gate Repair
Most electric gates in Temple City are retrofits. A 1960s ranch home got renovated in 2005 or 2015, and somebody bolted a motorized operator onto a gate and wall that were never built for it. The operator works fine for a few years, then the control board starts throwing faults, the remote stops pairing, or the motor runs but the gate barely moves. We service LiftMaster, DoorKing, Viking, Ghost Controls, Elite, and the other common brands, and we carry control boards, receivers, and limit switches so we’re not waiting on parts for a week.
Automatic Gate Repair
An automatic gate in Temple City fails in specific ways. The heat here pushes steel frames past 130 degrees on a summer afternoon, and that expansion is enough to make a gate that closed perfectly in May miss its latch in August. Add a Santa Ana wind event with 40-mile gusts hitting a 14-foot steel swing gate, and you get racked frames, stripped gears, and hinge welds that tear. We diagnose the root cause, not just the symptom: the sagging gate is almost never the panel’s fault. It’s the post, the hinge, or the footing.
Hinge & Post Repair
This is the big one in Temple City. The original perimeter walls on these 1940s-to-1970s ranch tracts are concrete block, built as property boundaries, not structural supports. During renovations, homeowners hang heavy steel swing gates on those existing block pilasters using hardware that was never meant to carry motorized gate load. The anchors pull out, the pilaster leans, the gate drops. We re-core and fill the footing, set structural grout, weld new hinge brackets, and re-hang the gate so it cycles square again. Fix the panel without the post and you’ll fix it twice.
Gate Realignment
Triple-digit Inland San Gabriel Valley heat does a number on long steel gates. They expand, they drift, the latch misses the post, and the opener starts throwing fault codes because it’s working against a gate that’s binding at the hinge. Realignment means cutting and re-welding the frame, resetting the hinge geometry, and tuning the opener limits so the gate doesn’t fight itself every cycle. We do the welding on site, in your driveway, so the gate never leaves your property.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Temple City
We’re certified to service nine major gate brands, and the ones we see most in Temple City’s older ranch neighborhoods are Viking, DoorKing, and Ghost Controls. Those legacy operators from the mid-2000s renovation boom are getting to the age where control boards die and gear racks strip, and parts aren’t always sitting on a shelf. We keep the common failure parts in stock for Temple City customers and can weld what can’t be ordered. If you’ve got an obsolete control board and a gate that still has good bones, we’ll tell you honestly whether retrofitting is worth it or whether a new operator is the cheaper answer over the next five years.
Common Gate Repair Problems We See in Temple City Homes
- Hinge anchor pull-out from unreinforced CMU pilasters. This is the dominant failure mode in Temple City, where swing gates were retrofitted onto non-structural block walls during whole-property renovations. The anchors embedded in unreinforced block work loose under daily cycling, the pilaster starts to lean, and the gate drops.
- Alignment drift on long steel swing gates from summer heat. Inland San Gabriel Valley temperatures regularly push past 95 degrees, and that thermal expansion changes the gate geometry enough to cause latch miss. A gate that closes fine at 8 a.m. may not close at 3 p.m. in August.
- Debris-packed slide gate tracks on rear alley access points. Temple City’s mid-century subdivision layout backs many lots onto alleys, so slide gates there take abuse from city maintenance vehicles and weekly trash trucks. Packed tracks and shattered nylon rollers are a recurring call we don’t see at the same rate in coastal cities.
- Obsolete control boards on legacy operators. The renovation-era operators installed in the 2000s and early 2010s are hitting end of life. We see dead remotes, boards that won’t hold programming, and safety edges that fail intermittently. Some can be retrofitted with modern safety photocells; some should be replaced.
Pricing for Gate Repair in Temple City, CA
You’ll know the price before we start. Here’s what Temple City homeowners typically pay:
- Hinge and post repair: $280-$650 depending on whether we’re re-coring and filling the footing or just replacing hardware and re-welding the bracket.
- Gate realignment and re-weld: $220-$480 for cutting, squaring, and re-hanging a steel swing gate.
- Electric operator or control board repair: $180-$520 depending on the brand and whether parts are on the truck or need to be ordered.
- Slide gate track and roller replacement: $190-$450 for clearing packed tracks, replacing rollers, and resetting the track line on an alley gate.
Every quote is agreed before work begins. Not an estimate range, not a “we’ll see when we get in there” - a written number. We also offer $40 off any repair over $200, a free second opinion on any written estimate from another company, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Temple City
If you’re in Rosemead, San Gabriel, Arcadia, or East San Gabriel, we do the same work there. But if you’re in Temple City proper, check the Temple City page for details specific to your neighborhood. Our Gate Repair team covers the whole San Gabriel Valley corridor with the same 90-Day Done Right Promise.
Serving Temple City, CA - Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Temple City
Because the block wall was never meant to hold a motorized gate. Temple City’s original ranch homes were built with CMU block perimeter walls as property boundaries, not structural supports. When a heavy steel swing gate gets retrofitted onto that block during a renovation, the hinge anchors are set into unreinforced material that can’t handle repeated motorized cycling. The fix is structural: re-core the footing, fill with grout, and set a properly welded hinge bracket. It’s a real repair, not a re-tighten job. Call (877) 610-2993 and we’ll tell you exactly what your wall needs.
Sometimes, yes. If the operator’s control board can accept a photo eye input, we can add a set of safety photocells so the gate reverses if anything crosses the path. The issue with 1960s-era gates is usually the gate itself, not the operator: the mounting wasn’t built for modern safety standards, and the hinge geometry may need reworking before the photocells will work reliably. We’ll look at the whole setup and tell you if a retrofit is realistic or if you’d be better off replacing the operator now rather than paying twice.
You fix the hinge post, not the panel. A gate sags in the hinge post, not in the middle, and that’s where we start. If the post has pulled away from the CMU pilaster, we re-core the footing, fill it with structural grout, set a new welded hinge bracket, and re-hang the gate so it closes square. We do it on site in your driveway. You keep the wall, keep the gate, and stop paying for hinge bolts that pull loose every six months.
Yes, and it’s specific to how Temple City was laid out. The mid-century subdivision design put rear alleys behind many lots, and those alleys carry city maintenance vehicles and weekly trash trucks. The slide gate track set into the alley-grade concrete pad gets packed with debris and the nylon rollers shatter under the load. It’s not a coastal problem or a hillside problem. We clear the track, replace the rollers with heavier-duty ones where it makes sense, and reset the track line so it stops eating itself. Call (877) 610-2993 and we’ll take a look.
Yes, and it starts with how the hinge is anchored. Once we’ve repaired a pulled hinge on a Temple City CMU wall, we can add structural reinforcement to the footing and set the hinge bracket for load so it doesn’t re-fail the same way. For gates that are already leaning, the prevention is the repair itself: don’t wait until the gate drags on the driveway. The sooner the hinge is addressed, the less damage the cycling does to the wall. Estimates are free, and the number is (877) 610-2993.
Call Gatewood Fence & Gate for Temple City Gate Repair
If your gate is sagging, grinding, jamming, or just refusing to open, call (877) 610-2993. A live person answers. We’ll give you a straight answer, a written price, and a repair that holds. Hal Gatewood has been fixing gates since 2001, and the name is on the shop. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Temple City and the San Gabriel Valley.