Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Redondo Beach, CA
Gate repair in Redondo Beach comes down to two things most of the time: salt corrosion and tight working space. The marine layer settles over this city nearly every night of the year, and that salt-laden air gets into hinges, motor housings, and control boards faster than anything we see ten miles inland. If your gate groans, sags, or stopped opening altogether, call (877) 610-2993 and a live person answers. We show up, give you a straight price, and fix the gate right there in your driveway more often than not.
What makes Redondo Beach different is the housing stock. North Redondo’s alley-grid bungalows have rear gates that double as trash-bin staging areas. South Redondo’s condo complexes run aging slide-gate operators on shared driveways. Both demand different fixes, and both get hit by the same salt air every night.
Why Redondo Beach Homes Are Different
Redondo Beach sits within one to two miles of the Pacific for virtually the entire city. The salt-laden marine layer settles over metal gate components every single night. Hinges, frames, latches, and automated motor housings corrode at a rate dramatically faster than inland South Bay cities like Torrance or Hawthorne. Hardware and powder coatings that would last a decade inland may fail in three to five years here. This isn’t a theory. It’s what we see every week when we open a seized hinge pin or a rusted motor housing on a gate west of Catalina Avenue.
Properties on blocks closest to King Harbor and the open coast get hit even harder than the city’s inland edge, because the salt aerosol concentration is higher. The 90278 zip code has its own distinct problem: rear alley gates take repeated hits from trash bins and delivery vehicles while also fighting corrosion. That combination failure mode, salt plus impact, doesn’t show up in Manhattan Beach or El Segundo the same way. In the alley-grid neighborhoods of North Redondo, rear gates serve double duty as informal staging areas, so we routinely find hinges that are both salt-corroded and impact-bent. Fixing that correctly means heavier-gauge hinge replacements than a standard residential job. A gate repair contractor in Redondo Beach who treats this city like any other will install the wrong hardware, and the gate will fail again within a few years.
Gate Repair in Redondo Beach
Gate repair in Redondo Beach usually means salt corrosion on coastal properties and tight working space on inland lots. We fix the gate where it stands, whether that’s a rear alley in 90278 or a shared driveway off Catalina Avenue. Hal Gatewood runs every job himself or puts his own crew on it, and the repair-first approach means we weld on site instead of hauling your gate off to a shop. Here’s what gate repair actually costs: a basic hinge replacement runs $180-$320, gate realignment and latch adjustment runs $150-$280, and electric gate opener repair runs $250-$480 for most control board, limit switch, or motor issues on Viking, Ghost Controls, DoorKing, and Elite systems. Gate Repair starts with finding what actually failed, not quoting you for parts that didn’t.
Electric Gate Repair
Electric gate problems in Redondo Beach usually start with the motor housing. Salt aerosols get into the electronics and connections, and three to five years is about what you get from a control board near the coast before corrosion starts causing intermittent failures. We open the housing, clean and test the board, replace what’s actually failed, and seal it properly so you’re not calling us again next spring. Electric gate opener repair typically runs $250-$480 for most control board, limit switch, or motor issues on Viking, Ghost Controls, DoorKing, and Elite systems in both 90277 and 90278.
Automatic Gate Repair
Automatic gates in Redondo Beach fail for two distinct reasons depending on which side of town you’re on. In 90277 near the coast, it’s almost always corrosion on the operator arm, limit switches, or wiring connections. In 90278, the alley grid beats on the gate itself, and the opener gets strained trying to move a sagging, binding panel. We diagnose the operator and the gate together, because fixing one without addressing the other just moves the problem six months down the road. Automatic gate repair work on operator arms and limit switches generally falls between $250 and $480 for most common failures.
Hinge & Post Repair
Here’s the thing about Redondo Beach: in the 90278 alley-grid neighborhoods, rear gates serve double duty as staging areas for trash bins and delivery access. Hinges are routinely both salt-corroded and impact-bent, a combination failure mode that almost never appears in neighboring Manhattan Beach or El Segundo. We cut out the rotted post footing, set a heavier-gauge steel post in a deeper concrete pour, and hang the existing panel with new salt-resistant hinges. Fix the panel without the post and you’ll fix it twice. Hinge replacement on a standard gate runs $180-$320, and weld and rust repair starts around $200 for a small panel patch and goes up to $600 if we’re cutting out a rotted post footing and setting new steel.
Gate Realignment
A gate that drags or won’t latch is almost always a post problem, not a panel problem. On tight Redondo Beach lots where gates sit close to garages and alley rights of way, even a quarter inch of post lean turns into a gate that binds every time. We measure the post against the gate’s swing path, correct the lean, and reset the latch so the gate clears the bin path without binding. Gate realignment and latch adjustment typically runs $150-$280. A gate sags in the hinge post, not in the middle, and that’s where we start.
Why do gate hinges rust so much faster in Redondo Beach than in Torrance or Hawthorne?
Redondo Beach sits within one to two miles of the Pacific for virtually the entire city, and the nightly marine layer carries salt aerosols that penetrate even painted steel and wrought iron. Hinges and frames that would last a decade inland fail in three to five years here. The fix is salt-resistant hardware and proper sealing, which we install as standard on every Redondo Beach job. Call (877) 610-2993 for an exact quote, estimates are free.
Can my rear alley gate in 90278 be repaired if it was hit by a trash bin and the hinge post is leaning?
Yes, and it’s a repair we do regularly in North Redondo’s alley-grid neighborhoods. We cut out the rotted or shifted post footing, set a heavier-gauge steel post in a deeper concrete pour, and hang the existing panel with new salt-resistant hinges. We also check the latch alignment so the gate clears the bin path without binding. Call (877) 610-2993 and we’ll give you a real window for getting out there.
Gate Installation in Redondo Beach
Gate installation in Redondo Beach usually runs $1,400 to $3,800 for a standard driveway gate, with sliding gates on the higher end because of the track work and operator. Most jobs we quote in the 90277 and 90278 zip codes take one to two days once materials are on site. If you’re standing in a shared driveway off Catalina Avenue or a rear alley in North Redondo trying to figure out whether a gate will even fit, call (877) 610-2993 and we’ll measure it. Gate Installation starts with the post, because hanging a new gate on failing steel is how you pay twice.
Sliding Gate Installation
Sliding gates are the workhorse in Redondo Beach, especially in 90278 where a rear alley or narrow side yard makes a swing gate impossible. A cantilever slide gate doesn’t need a track on the ground, which matters when salt and sand from the marine layer would bind up a track system within a few seasons. We install Viking and DoorKing slide operators with the rack and pinion gears properly aligned, because a misaligned rack is the fastest way to burn out a motor in this salt air. Sliding gate installation for a single-car opening typically runs $2,200 to $4,500 in Redondo Beach depending on the operator and track work.
Swing Gate Installation
Swing gates work on Redondo Beach homes with a wider front driveway or a side yard that doesn’t back up to an alley. The real issue here is the hinge post. Salt aerosols corrode the post faster than the gate panel, and once the post starts to go, the gate sags and strains the footing until it seizes or snaps. We use heavier-gauge posts and marine-grade hardware on any swing gate within a mile of the coast. A single swing gate installation typically runs $1,400 to $3,200, and if the existing hinge posts are corroded, we replace them rather than hang a new gate on failing steel.
Security Gate Installation
Security gates in Redondo Beach tend to cluster in two places: the condo and townhome complexes of 90277 near King Harbor, and single-family homes west of Catalina Avenue where foot traffic from The Strand is a constant. These jobs usually require an access control component: a keypad, a telephone entry system, or a loop detector for vehicles. We install and program those systems, then test them with you before we call the job done. A security gate install with access control typically runs $2,800 to $6,500 in Redondo Beach depending on scope.
Pedestrian Gate Installation
Pedestrian gates in Redondo Beach are the quiet workhorses of the alley-grid blocks in 90278. They get opened and closed more times per day than any driveway gate, they take the brunt of the salt air, and they’re the first thing to sag when a post starts to fail. We install pedestrian gates with self-closing hinges where code requires it, and we always check swing direction and latch placement against how you actually use the gate. A basic pedestrian gate install in Redondo Beach typically runs $500 to $1,400 including hardware and post setting.
Can I put a swing gate on my Redondo Beach alley driveway if there isn’t enough room?
Usually not. Swing gates need clearance beyond the gate leaf to arc open, and most rear alley driveways in 90278 don’t have it. The gate would either block the alley or hit the structure behind you. A sliding gate often works in that same footprint because it travels sideways along the fence line instead of swinging out. Call (877) 610-2993 for a free measure and we’ll tell you what fits.
Do automatic sliding gates in Redondo Beach need photo-eyes on a shared driveway?
Yes. Shared driveways in 90277 and shared alley access in 90278 require photo-eyes and often a reversing edge to meet entrapment safety standards. If the photo-eyes are misaligned or missing, the operator will fault out and the gate will stop working. We align and test them as part of every automated install. Call (877) 610-2993 and we’ll check your setup before it fails.
Gate Motor & Opener in Redondo Beach
Gate motor and opener failure in Redondo Beach is almost always salt corrosion working its way into the housing. The marine layer gets into the control board, the limit switches, and the wiring connections, and three to five years is about what you get from an opener near the coast before intermittent failures start. We service Viking, Ghost Controls, DoorKing, and Elite openers in both 90277 and 90278. Gate Motor & Opener repair runs $250 to $480 for most control board, limit switch, or motor issues, and a full operator replacement with coastal-rated hardware runs $800 to $1,800 depending on brand and gate weight.
Opener Motor Repair
When an opener motor fails in Redondo Beach, the usual cause is corrosion on the windings or a seized bearing from salt intrusion. We open the housing, test the motor under load, and replace what actually failed rather than quoting a whole new operator. Opener motor repair typically falls in the $250 to $480 range on most residential systems in 90277 and 90278.
Limit Switch & Control Board Repair
The limit switches and control board are the parts that tell your gate where to stop and when to reverse. Salt air corrodes the contacts, and the gate starts stopping in the wrong place or faulting out for no reason. We clean and test the board, replace limit switches when they’re beyond saving, and seal the housing so the next foggy night doesn’t undo the work. Control board and limit switch repair on Gate Motor & Opener systems in Redondo Beach usually runs $250 to $480.
Operator Replacement
Sometimes the opener is too far gone, and that’s when we talk straight with you about replacement. In Redondo Beach, we spec coastal-rated operator hardware that’s built for salt exposure, not the inland version that fails in three years. Full operator replacement with coastal-rated hardware runs $800 to $1,800 depending on the opener brand and the gate’s weight. The price is quoted and agreed before any work starts.
Why did my automatic gate opener stop working after only three years on a Redondo Beach property?
Salt corrosion is the usual culprit. The marine layer gets into the motor housing, control board connections, and limit switches, and three to five years is about what you get from an opener near the coast before corrosion starts causing intermittent failures. You don’t need a new opener just because a connection corroded. Call (877) 610-2993 and we’ll test it on site.
Can you repair my automation instead of replacing the whole gate in Redondo Beach?
Yes, and that’s the default. We open the housing, diagnose the actual failure, and replace only what’s dead. A corroded board, a failed limit switch, or a seized bearing doesn’t mean a new gate or even a new operator. The repair-first approach is how Hal has run things since 2001. Call (877) 610-2993 for an exact quote.
Gate Access Control in Redondo Beach
Gate access control in Redondo Beach usually means one of three things: a keypad that stops reading after a foggy night, a shared condo gate that won’t open for resident remotes, or a slide gate operator that seized because the salt air got inside the motor housing. We handle all three, plus phone entry, card readers, video intercoms, and smart access systems. Gate Access Control work in 90277 condo complexes is different from 90278 alley-grid bungalows, because the failure modes are different.
Keypad Entry
Keypads in Redondo Beach fail in a specific way: salt-laden air works into the rubber membrane and corrodes the contact traces underneath, so codes start working intermittently after a foggy morning. That is not a dead keypad, it is a corroded one, and we can often rebuild the internals on site rather than replacing the whole unit. Keypad entry installation on an existing single-family gate runs $180 to $380 including the keypad and programming in Redondo Beach.
Remote Control and Receiver Repair
When a shared condo gate slides fine but won’t open for residents’ remotes, most people blame the remote. In Redondo Beach’s 90277 complexes, we more often find the receiver board has corroded contacts or the antenna has been knocked loose inside the housing. We test the transmitter first, then the receiver, then the operator, and we replace only what actually failed. Receiver board repair on Gate Access Control systems typically runs $250 to $500 per reader depending on mounting and condition.
Phone Entry Systems
Phone entry is the most requested upgrade in Redondo Beach multi-unit buildings, especially where residents want visitors to call from the pedestrian gate and get buzzed in from a cell phone. We wire phone entry systems into existing gate operators and configure the call routing so it works with each resident’s phone carrier. Phone entry systems for multi-unit properties start around $700 and go up from there depending on the number of resident entries in Redondo Beach.
Why does my keypad entry stop working after a foggy morning near the Redondo Beach coast?
The marine layer deposits a fine salt film on the keypad contacts, which creates intermittent conductivity that makes codes fail when the air is damp and work again when it dries. The fix is cleaning and sealing the internals, or replacing the keypad with a sealed unit rated for direct coastal exposure. Call (877) 610-2993 and we’ll diagnose it on site.
My shared condo gate slides fine but won’t open for residents’ remotes - is it the operator or the receiver?
In Redondo Beach’s 90277 complexes, this is usually the receiver board inside the operator housing, not the operator motor or the remotes themselves. We test the transmitter output first, then open the housing and inspect the receiver contacts. If the receiver board is corroded, we replace just that board when the brand supports it. Call (877) 610-2993 and we’ll sort it out.
Gate Parts & Welding in Redondo Beach
When a gate hinge tears loose or a post rots inside its footing, the fix usually means one of two things: finding the right part for a gate that was installed years ago, or welding the existing steel back together so it stays fixed. Redondo Beach makes that work harder than most places. The salt air that drifts off Santa Monica Bay attacks gate hardware from King Harbor to the 90278 alleys. Gate Parts & Welding means we bring the welder, the generator, and the steel to your driveway, and the gate never leaves Redondo Beach.
Hinge Replacement
Around the coast-adjacent blocks west of Catalina Avenue in 90277, hinge seizure is common. Salt aerosols work into the knuckle, the barrel swells, and the gate starts pulling the post out of plumb. We replace hinges with marine-grade steel and heavier-gauge barrels than the originals. In Redondo Beach, hinge replacement on a standard single swing gate typically runs $220 to $440, depending on whether it’s one hinge or three and whether we’re welding new hinge plates to the frame.
Post Replacement
When the hinge post itself is compromised, replacing it means digging out the old footing, setting a new post in concrete, and welding or mounting the gate back square. Redondo Beach’s rear-alley gates sit tight to wooden fences and stucco walls, so the post work has to be precise. Post replacement, including removing the old post, setting a new galvanized post in concrete, and re-hanging the gate, usually lands between $550 and $950 in Redondo Beach.
Custom Welding
Sometimes the right answer is fabrication. Whether it’s a missing bottom brace on a 1970s ornate gate in 90277 or an oversized sliding gate at a condominium complex that needs the operator mount reinforced, we weld on site. Rail repair and custom welding jobs run $180 to $520 for small localized patches, and more when we’re splicing in longer sections or fabricating a missing brace in Redondo Beach.
Is emergency gate welding available in Redondo Beach?
Yes. If your gate has broken loose and you need it secured tonight, we can come out, assess the damage, and do the critical weld or post bracing to get the gate secure. The full cosmetic repair or replacement can follow if needed. Call (877) 610-2993 and we’ll talk you through what’s safe and what’s temporary.
What warranty do you offer on gate parts and welding in Redondo Beach?
Every gate part and weld is backed by the 90-Day Done Right Promise. If something we did fails within 90 days, one call brings us back to Redondo Beach to make it right at no charge. That’s in writing on your invoice. Call (877) 610-2993 and we’ll stand behind the work.
Brands We Service in Redondo Beach
We service Viking, Ghost Controls, DoorKing, and Elite systems across Redondo Beach, with common parts stocked locally so we’re not waiting on a shipment. Our brands coverage means most board and limit switch replacements are same day on systems from those four manufacturers.
Pricing for Gate Repair in Redondo Beach, CA
| Service | Typical range in Redondo Beach |
|---|---|
| Hinge replacement | $180 - $320 |
| Gate realignment & latch adjustment | $150 - $280 |
| Weld & rust repair (panel patch) | $200 - $600 |
| Electric gate opener repair | $250 - $480 |
| Pedestrian gate installation | $500 - $1,400 |
| Single swing gate installation | $1,400 - $3,200 |
| Sliding gate installation | $2,200 - $4,500 |
| Security gate with access control | $2,800 - $6,500 |
| Keypad entry installation | $180 - $380 |
| Phone entry system (multi-unit) | $700+ |
| Full operator replacement | $800 - $1,800 |
| Post replacement & re-hang | $550 - $950 |
What pushes these numbers up in Redondo Beach is salt. Corroded posts, failed boards, and rusted hardware all add repair scope, and we quote the price up front so you know the real number before we start.
Neighborhoods We Serve in Redondo Beach
We work the full city, from the Hollywood Riviera down through the Village and across both zip codes. Most repair calls in Redondo Beach get same-day response when a gate is stuck and blocking access.
- Hollywood Riviera
- Golden Hills
- The Village
- North Redondo (90278)
- South Redondo (90277)
Service Area - Cities Near Redondo Beach
We also serve the surrounding South Bay communities, including Redondo Beach, CA, Hermosa Beach, CA, Palos Verdes Estates, CA, Manhattan Beach, CA, Marina del Rey, CA, and Lawndale, CA. The same salt air hits all of them, and we treat the work the same way.
Serving Redondo Beach, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Redondo Beach and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Redondo Beach coverage area; if your address is on it, we can help.
Also serving nearby: Redondo Beach, CA, Hermosa Beach, CA, Palos Verdes Estates, CA, Manhattan Beach, CA, Marina del Rey, CA, Lawndale, CA.
FAQs About Gate Repair in Redondo Beach
We answer every call with a live person, 24/7, and for a gate that’s fallen off its hinges, wedged open, or blocking a driveway, we can usually have someone in Redondo Beach the same day in most cases. Call (877) 610-2993 and tell us what happened. We’ll give you a real window, not a four-hour sometime range.
Most gate repairs and replacements on existing footings don’t require a permit in Redondo Beach, but new post footings and automated operators on shared driveways sometimes trigger review. We’ll tell you what applies to your specific property before any work starts, and we handle the paperwork when needed. Call (877) 610-2993 and we’ll walk you through it.
Yes. We work the coastal condos and townhomes in 90277 from King Harbor east, and the single-family alleys and rear gates throughout North Redondo and 90278. We’re familiar with the narrow access, the tight fence lines, and the way salt and bin traffic combine on those alley gates. Call (877) 610-2993 and we’ll get you on the schedule.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Redondo Beach Customers Say
"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield