Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across North Castle
Gate repair in North Castle usually means one of three things: a swing gate that no longer lines up with the latch, an operator that hums but won’t move the gate, or a post that frost heave has pushed out of plumb. Most calls we run in North Castle are diagnosed and fixed the same visit, and we quote the price before any wrench turns. If your gate is dead, sagging, or binding, call Hal Gatewood at (877) 610-2993 and a live person answers, day or night.
We have worked the Armonk end of North Castle long enough to know what the heavy stone pillars and gravel drives do to gate hardware over twenty or thirty winters. That local read on the problem saves you the cost of replacing parts that are not actually the failure. More on that below.
Why Gatewood Fence & Gate Is North Castle’s Preferred Gate Repair Company
Hal Gatewood started this shop in 2001 and never handed it off to a franchise or a call center. The name on the invoice is the name on the shop, and if something on your gate is not right, one call brings him back. That is the 90-Day Done Right Promise, in writing on every job we do in North Castle.
North Castle homeowners tend to have researched us before they pick up the phone. They ask about the license number, the address, how long we have been at it. All of that is published. They also ask who shows up at the house, and the answer is an employee of ours, background-checked and in uniform, not a subcontractor we have never met.
We service the nine brands you actually see on older North Castle estate gates: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Knowing this specific hardware matters, especially on Armonk properties where the original operator may have been installed during the IBM executive building boom and is now twenty or thirty years old.
Our Gate Repair Services in North Castle
Electric Gate Repair
Dead keypad, operator that trips the breaker, gate that only moves halfway. Electric gate repair in North Castle usually traces back to the control board, the capacitor, or a corroded wire run between the operator and the house. On pre-UL 325 systems from the 1980s and 1990s, we commonly retrofit a modern control board and add entrapment protection photocells rather than scrapping a well-built gate. A typical electric gate repair in North Castle runs $260 to $480, parts included.
Automatic Gate Repair
When the motor runs but the gate does not, or the gate reverses for no reason, the issue is often the limit switch, the drive chain, or a gear stripped by years of freeze-thaw stress. Automatic gate repair in North Castle frequently means opening the operator box on a stone pillar and finding water intrusion that has been building up every winter since 1995. We fix the cause, not just the symptom, so you are not calling us again in March.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and that is where we start. On North Castle estates, the hinge post is often set in a poured concrete footing that oak roots have slowly lifted over twenty years. We reset the footing with a root-bridging pad that gives the post a stable seat without cutting into protected root systems. Hinge and post repair in North Castle typically runs $340 to $700 depending on whether the post needs to come out or can be re-bedded in place.
Gate Realignment
If your swing gate drags on the ground or the latch misses by a half inch, the frame is still fine in most cases. Gate realignment means adjusting or re-shimming the hinge points, and sometimes correcting the post angle itself. After a hard North Castle winter, the ground movement alone can throw a heavy iron gate out of plumb by an inch. Realignment usually runs $180 to $320, and we quote it before we touch a bolt.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Castle
Most North Castle service calls involve legacy hardware: LiftMaster, Elite, Linear, Viking, DoorKing, and Ghost Controls are the names we see on the boxes week in and week out. We keep control boards, limit switches, remote receivers, and photocell kits stocked for these brands in our service vehicles, so a repair is not stalled while parts ship from a warehouse. If your operator is one we certified on, the part is usually on the truck when we pull into your driveway.
Common Gate Repair Problems We See in North Castle Homes
- Frost-heaved pillars. North Castle sits in the inland Westchester hills, and every winter the ground freezes and expands under heavy stone and masonry gate pillars. That inch of movement throws the gate out of plumb and the operator arm out of alignment. Spring is our busiest season because that is when the damage from January and February shows up.
- Obsolete 1980s and 1990s control boards. The Armonk estate boom installed a generation of LiftMaster and Elite operators that were not built to current UL 325 entrapment standards. Decades of moisture intrusion corrode those boards until the gate simply goes dead. We can retrofit the safety circuits and board in most cases instead of replacing the whole operator.
- Tree roots under post footings. Mature oak and maple root systems along Armonk gravel drives do not stop at the property line. Over twenty or thirty years they migrate under gate post footings, lift the post, and tear the operator arm off its bracket. Fixing the panel without addressing the footing means you will fix it twice.
- Worn rack and pinion teeth on slide gates. Slide gates on North Castle estates take a beating from freeze-thaw cycles that bind the track and from gravel that works its way into the gear track. Once a few teeth strip, the gate jumps and grinds. We weld or replace the rack section and then address the track alignment that caused the wear.
Pricing for Gate Repair in North Castle, NY
Gate repair pricing in North Castle is straightforward once we know what we are dealing with. A simple gate realignment typically runs $180 to $320. Hinge and post repair, which usually involves resetting a footing or replacing bent hardware, lands between $340 and $700. Electric gate repair, meaning control boards, limit switches, wiring, and photocell work, falls in the $260 to $480 range. Full automatic gate operator replacement on an Armonk estate, including the new operator, mounting hardware, and safety edges, starts around $1,100 and goes up from there depending on gate weight and pillar condition.
You get the exact price before we start, written down, and that is the number on the invoice. No trip charge inside the county, no surprise line items, and $40 off any repair over $200. Call (877) 610-2993 for a free estimate on your North Castle gate.
We Also Serve Cities Near North Castle
We run daily routes from our New York City office into North Castle and the surrounding area. If you are in White Plains, Pound Ridge, Hartsdale, or Greenburgh, the same crew and the same pricing apply. The Gate Repair team covers the whole Westchester corridor, and Gate Repair in North Castle is where most of our legacy-operator work happens.
Serving North Castle, NY - Our Local Coverage Area
We’re based in the North Castle area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in North Castle
Frost heave is the usual answer. The ground under your gate posts froze and expanded all winter, and when it thawed in March or April, the post settled a few fractions of an inch out of where it sat in the fall. That small shift throws the gate out of plumb and the latch off center. We correct the post angle and re-shim the hinges, and if the footing keeps moving, we reset it with a deeper, root-aware pad. Call (877) 610-2993 and we can look at it this week.
In most cases we can retrofit. The motors and drive hardware in those older LiftMaster units were built heavy, and the board is the weak point. We replace the board with a modern UL 325 compliant unit, add the missing entrapment protection, and re-seal the enclosure against moisture. If the motor itself is drawing too much current or the gearbox has worn out, replacement becomes the cheaper fix. We will show you the readings and quote both options before you spend anything.
Yes. We cut no roots unless a root has already destroyed the footing beyond re-use, and even then we work with your arborist or landscaper before removing anything structural. In most cases we pour a root-bridging pad that spans the root zone and gives the post a stable seat without severing the root network. On a wooded estate off Route 22 in Armonk, our crew reset a cast-iron hinge post lifted nearly two inches by a mature oak root, replaced the bent hinges, and wired new safety photocells, all without disturbing the protected root system. That is the standard approach, not an exception.
Possibly, but it is more often the keypad’s backlight or the controller’s power supply getting weak in cold weather. Older keypads draw more current as the temperature drops, and if the transformer is marginal, the system drops voltage by half a volt and the keypad ignores input. We test the power supply first. If the keypad itself is the issue, we replace it with a sealed, weather-rated unit that does not care if it is five degrees on an Armonk February morning.
Almost never. The panel is usually fine; the hinge post has moved or the hinge pins have worn. We re-align the hinges, new pins or bushings if needed, and the latch lines up again. If the post itself is the problem, we reset it. A new gate panel is the last recommendation we make, not the first. Call (877) 610-2993 and we will tell you straight what it needs and what it costs.
Call Gatewood Fence & Gate for North Castle Gate Repair
If your gate is dead, sagging, grinding, or just not closing the way it did last summer, call us. You will get a live person on the phone, a straight answer about what is wrong, and a written price before any work starts. Hal Gatewood has been at this since 2001, and the 90-Day Done Right Promise is on every job in North Castle. Call (877) 610-2993 now, or call anytime something fails. We answer around the clock.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Castle since 2001.