Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Castle
Gate parts and welding in North Castle usually fall into two camps: the hinge post has shifted or cracked, or the gate itself was built heavy enough that standard hardware gave up. On the large estate lots around Armonk, where stone pillars and custom ornamental iron are the norm, we handle both every week. Gatewood Fence & Gate has been owner-operated since 2001, and Hal Gatewood still takes the calls. If your gate is sagging, binding, or the post is leaning after another North Castle winter, call (877) 610-2993 and Hal will tell you straight what it needs and what it will cost before any work starts.
We work across all of North Castle, from the winding drives off Route 128 to the newer cul-de-sacs east of Route 22, and we’re set up to weld on site so your gate stays in your driveway. Not hauled to some shop across the county.
Why Gatewood Fence & Gate Is North Castle’s Preferred Gate Parts & Welding Company
North Castle is not a township where a faceless crew in a rental van cuts it. Too many homeowners here have been burned by outfits that quoted one number on the phone and presented another at the door. Our company does things differently. Hal Gatewood’s name is on the shop, his license number is published, and the address is real. You want to look him in the eye before he touches your gate? Drive over. He lives in the same world you do.
We’re locally owned and owner-operated, which means the guy who answers the phone at 2 a.m. is the same guy who stands behind the work. Every job carries our 90-Day Done Right Promise in writing. Not “up to” or “in most cases.” If it isn’t done right, one call brings Hal back, no runaround. North Castle customers also get a free second opinion on any written estimate, no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Those offers don’t require haggling. They’re standing.
Our Gate Parts & Welding work in North Castle runs on a simple principle: fix the panel without the post and you’ll fix it twice. We start at the hinge post. That’s where a sag actually begins.
Our Gate Parts & Welding Services in North Castle
We don’t sell replacement gates as a first answer. Most of what fails on a North Castle estate gate is a part, a weld, or a footing, and swapping the whole structure is money you didn’t need to spend. Here’s what we do most often.
Hinge Replacement
Wrought-iron swing gates around North Castle are heavy. Decades of opening and closing, plus the slow drift of a frost-shifted pillar, put enormous stress on hinge barrels and pins. We see hinge pins worn to half their original diameter on Armonk estates, and the gate still swings but it’s chewing itself apart. We fabricate and install heavy-duty hinges matched to the gate’s weight, then true the panel so it closes on center. On most of these jobs we weld new hinge leaves directly to the post, not bolt them. Bolts loosen. Welds don’t.
Post Replacement
If your North Castle gate post is cracked at the base, leaning, or pulling out of its footing, the gate cannot be fixed by adjusting the hinges. The post is the foundation. We cut out the old post, dig a deeper footing, and reset with high-strength epoxy anchors sized for the gate’s weight. In Armonk especially, we deal with root pressure from mature oaks and maples that have spent thirty years working under post footings. We dig around those roots rather than through them. Your landscaper will notice the difference.
Rail Repair
Slide gates on North Castle driveways take a beating. A rail that’s even slightly out of level will cause the gate to bind, jump, and eventually stall a perfectly good operator. We see this constantly after spring thaw, when frost heave has pushed one section of the track up by a half-inch. We cut out the damaged rail section, weld in new steel, re-level the run, and align the rollers so the gate glides without grinding. A smooth slide gate shouldn’t sound like a train yard.
Custom Welding
A gate can sit in the middle of a landscaped entrance, so it needs to look like it belongs. We can replace and fabricate, in matching gauge, any ornamental element on your North Castle gate that’s rusted through, snapped, or was poorly repaired by someone before us. Whether it’s a scroll that’s broken off, a finial that’s cracked, or a bottom rail that’s rotted from inside, we weld on site and match the patina so the new work doesn’t shout at the old. Hal has been welding since 2001. He’s seen just about every flaw a North Castle gate can throw at him.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Castle
We’re certified to service nine major gate brands, and on North Castle jobs we most often see LiftMaster, Elite, FAAC, DoorKing, Linear, and Viking operators on the estates. We stock common boards, limit switches, and receiver parts for these brands, which means we aren’t waiting a week for a part to ship across the country. For a North Castle customer with a gate stuck open, that matters. We also work on Ghost Controls and Mighty Mule systems on smaller residential gates. The point is simple: if your gate operator has a nameplate on it, we can likely service it, and we can usually do it same-week.
Common Gate Parts & Welding Problems We See in North Castle Homes
North Castle’s inland Westchester hills bring a specific set of failures. Here’s what our crew finds most often on the estate drives around Armonk and the surrounding roads:
- Frost-heaved stone pillars. Every winter, the freeze-thaw cycle works on the heavy stone and poured-concrete gate pillars that anchor swing gates. By March, a pillar that shifted an inch has thrown the gate out of plumb, bound the hinges, and left the latch half an inch from striking. We reset pillar anchors and re-true the gate before it tears itself apart.
- Oak and maple root pressure under post footings. Mature hardwoods line many North Castle driveways. Roots grow under post footings over decades, lifting them a fraction at a time until the hinge post is out of level and the operator arm is fighting the gate. This is the classic “the gate was fine last year” call. We reset the footing without destroying the root network your trees depend on.
- Cracked underground conduit to gate operators. Repeated freeze-thaw cycles crack PVC conduit runs under North Castle driveways. Water gets in, freezes, and shorts the low-voltage wiring to your LiftMaster or Elite operator board. We’ll trace the run, splice or replace the damaged section, and seal it so water stays out.
- Sagging wrought-iron panels with worn hinge hardware. On a heavy custom gate, the panel itself rarely fails. It’s almost always the hinge post or the hinge barrels that have degraded. We replace the hardware, weld the load-bearing components, and re-hang the panel so it swings clean. Fix the panel without the post and you’ll fix it twice.
Pricing for Gate Parts & Welding in North Castle, NY
You should know what you’re walking into before you sign anything. In North Castle, hinge replacement on a typical ornamental iron swing gate runs $380 to $850 depending on gate weight and whether we need to weld new hinge plates. A full post replacement, including cutting out the old post, digging the new footing, resetting with epoxy anchors, and re-hanging the gate, runs $900 to $2,400 on most Armonk estate drives. Rail repair on a slide gate generally falls between $450 and $1,100, depending on how much rail has to be cut out and re-welded. Custom welding work like reproducing a broken scroll or reinforcing a cracked bottom rail typically runs $180 to $600 per element, based on material and time.
The price you’re quoted is the price on the invoice. We don’t change it at the door. Every estimate is free, and we’ll put it in writing before any work starts. Call (877) 610-2993 and we’ll walk through what your gate needs and what it will cost. No surprises.
We Also Serve Cities Near North Castle
If you’re on the edge of North Castle or have family nearby, we cover a wide swath of Westchester and the surrounding towns. Our Gate Parts & Welding in North Castle service area extends naturally into White Plains, Pound Ridge, Hartsdale, and Greenburgh, and we’re on those roads every week.
Serving North Castle, NY - Our Local Coverage Area
We’re based in the North Castle area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Castle
Your gate pillar is moving. North Castle’s freeze-thaw cycles lift the heavy stone and poured-concrete pillars that hold swing gates, and when the ground thaws in March or April, the pillar settles a little differently than it sat before. That shift throws the gate panel out of plumb, and a heavy wrought-iron gate follows gravity downhill. The fix isn’t adjusting the hinges; it’s resetting the pillar or the hinge post so the foundation is level again. Call (877) 610-2993 and we’ll tell you if your sag is a pillar problem or a hinge problem. Usually it’s both.
Yes. We mount operators on stone and masonry pillars all the time across North Castle, and the key is a mounting plate and anchor system that spreads the load rather than drilling a half-dozen oversized holes into the stone. We also take care to route the conduit and the operator arm so they don’t rub against the pillar face. You won’t see a ring of chips around the mount when we’re done. If you want to see exactly how we’ll approach your pillar, call (877) 610-2993 and we’ll walk the job with you.
Almost always, the rail has moved. Frost heave under the track bed or the gate post pushes one section of rail a quarter-inch out of alignment, and that’s enough to make a heavy slide gate bind when it’s cold and every tolerance is tighter. We re-level the rail run, weld or replace any damaged rail sections, and re-align the rollers. We also check the operator arm and idler pulleys for wear while we’re in there. If your North Castle slide gate is grinding or stalling, call (877) 610-2993 and we’ll fix it before it burns out the operator.
Yes, and this is one of the things Hal genuinely enjoys. We can fabricate replacement scrolls, finials, hinge straps, and bottom rails in matching gauge steel or iron, weld them on site, and then treat or patina the new work so it doesn’t look like a patch. If the original fabrication was custom, we can usually match the profile. If you send us a photo of the broken element or the gate from a few feet back, we’ll tell you what’s possible and what it will cost. Estimates are free at (877) 610-2993.
Yes. On North Castle estates, we regularly service gates with keypad entries, loop detectors in the driveway, and intercom or camera tie-ins. The problem is rarely the operator itself; it’s usually a failing loop detection circuit, a keypad that’s lost its programming after a power surge, or a relay that isn’t sending the open signal. We troubleshoot the whole system, not just the gear box, so your gate opens when it should and stays closed when it shouldn’t. Call (877) 610-2993 with your keypad model and we’ll start there.
Call Gatewood Fence & Gate for Gate Parts & Welding in North Castle
If your North Castle gate is sagging, binding, or its post is leaning, call us at (877) 610-2993. A live person will answer, day or night. Hal will ask you what the gate is doing, give you a straight answer, and book a time that works. The estimate is free, the price you’re quoted is the price you pay, and our 90-Day Done Right Promise is in writing. North Castle has too many beautiful estate gates to let them limp along on worn hinges and cracked footings. We’ll set yours right.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Castle since 2001.