Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Medway
Spring is the season that separates a well-set gate post from a badly set one in Medway. If your driveway gate is dragging, binding at the latch, or refusing to close after the ground softens, the problem is almost never the motor. It’s the post underneath it. We’re Gatewood Fence & Gate, and we’ve been Gate Repair specialists since 2001, with on-site welding and a repair-first approach. Call (877) 610-2993 and you’ll get a live person who knows Medway’s clay soils and frost patterns, not a menu tree.
Why Gatewood Fence & Gate Is Medway’s Preferred Gate Repair Company
Hal Gatewood put his name on this shop in 2001, and his address is published for anyone who wants to check. That matters in a town like Medway, where people expect to see the same face at the hardware store they saw on the job. We answer every call with a live person around the clock, and the person who shows up to your gate is the person who will fix it, not a subcontractor reading a script. Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No runaround, no hedging.
Medway’s specific problem is groundwater. The town sits in the upper Charles River watershed, and low-lying lots along the corridor hold spring saturation longer than the higher streets. When we get called out for a gate that won’t latch, we don’t start with the latch. We start with a level on the hinge post. Show us the gate closing on its own and we’ll show you where it’s failing.
Our Gate Repair Services in Medway
Gate Realignment
A sagging gate in Medway is a post problem before it’s a panel problem. When footing clay heaves during freeze-thaw cycles, the hinge post tilts, the frame pulls out of square, and the latch no longer lines up. We re-set posts below frost depth and re-hang the leaf so the gate swings clean again. Fix the panel without the post and you’ll fix it twice.
Hinge & Post Repair
On older Medway properties near the historic town center, we regularly pull 20 to 40-year-old ornamental iron gates with hinges that have never been touched. Freeze-thaw cycles stress those hinge welds every winter. We repair or replace hinges on site, re-weld the frame joints, and reinforce the post connection so the gate doesn’t sag back within a season.
Electric Gate Repair
Medway gets real wind off the open lots, especially during nor’easters. A solid infill gate acts like a sail, and the operator takes that load every cycle. We service Linear, Viking, Ghost Controls, and DoorKing operators, and we diagnose the full system: board, limit switches, arm, and the post alignment underneath it. If the operator is worth saving, we save it. If it’s not, we’ll tell you that too and install a replacement that’s sized for your gate’s wind exposure.
Automatic Gate Repair
When a power cut leaves your gate stuck in Medway, the first step is the manual release, not the control board. We’ll show you exactly how to disengage your specific operator safely, then we’ll check for the follow-on damage that power interruptions cause: blown fuses, scrambled limits, and stripped rack teeth from the gate slamming on the re-energize. We carry parts for most major brands so we’re not waiting on a four-day freight order while your gate is open.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Medway
We’re certified to work on nine brands, and in Medway the calls we see most are Linear and Ghost Controls swing operators with post heave underneath, and Viking slide operators on exposed lots where wind has over-torqued the rack. We stock common parts locally, which means we can often repair a Linear swing arm or a Viking board the same day rather than scheduling a return trip. If your operator’s brand isn’t one of those, ask when you call. If it’s a brand we service, we’ll tell you straight. If it’s not, we’ll tell you that too, and point you toward the right fix rather than pretending.
Common Gate Repair Problems We See in Medway Homes
- Post heave on clay soils. Norfolk County clay absorbs spring meltwater and swells unevenly, pushing hinge posts up and out of alignment. This is the single most common reason Medway gates bind at the latch every March and April.
- Welded joint cracks on 20-40-year-old iron gates. Medway’s suburban buildout from the late 1980s through the 2000s produced a large cohort of ornamental iron driveway gates. Those gates have now been through two to three decades of hard frost cycles, and the welds at the frame corners and hinge mounts are the first things to fail.
- Wind-damaged operators on solid infill gates. Nor’easters put sustained wind load on a closed gate. Solid wood and metal infill panels don’t let wind through, so the operator’s arm and gear teeth absorb the force. We see stripped rack teeth and bent arms most often on slide gates along open road frontage.
- Spring latch failure from drainage shifts. Properties near the Charles River corridor sit on ground that drains slowly. Footings shift a quarter-inch at a time, enough to throw off the latch plate geometry so the gate won’t fully seat on the catch. It’s a chronic pattern we see on the same addresses year after year.
Pricing for Gate Repair in Medway, MA
We quote a price before work starts, and that price doesn’t change at the door. A hinge replacement on a residential swing gate in Medway typically runs $180 to $340 depending on the hardware. Gate realignment runs $200 to $400 when the post can be pulled back into true without excavation. A full hinge-post reset with re-pour below frost depth runs $600 to $1,100 in Medway’s clay, because the hole has to go down past 4 feet or you’re redoing it next spring. Electric gate repair on a Linear or Ghost Controls swing operator runs $225 to $475 for the typical board, limit, or arm repair. Viking slide operator repairs run $350 to $700 depending on the drive component. We offer $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a free estimate, and we’ll tell you the number before we touch a single bolt.
We Also Serve Cities Near Medway
If you’re in Millis, Holliston, Norfolk, or Medfield, we cover those towns too. The soil patterns shift as you move out of the Charles River watershed, so we read each property individually rather than treating every town the same. Call us from wherever you are in the area and we’ll tell you what we see on your street.
Serving Medway, MA - Our Local Coverage Area
We’re based in the Medway area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Medway
Your post is heaving in Medway’s clay soil. Norfolk County clay holds spring meltwater, swells, and pushes the footing up unevenly. Combine that with Massachusetts frost penetration up to 4 feet deep, and you get a post that drifts out of alignment every thaw cycle. The fix that lasts is resetting the post below frost depth on a proper concrete footing, not just adjusting the hinges. Call (877) 610-2993 and we can tell you whether your post is moving or your panel is sagging. Estimates are free.
First, find the manual release on your operator and disengage it so the gate can swing freely. The release is usually a small lever or pull-ring on the operator body. Do this before you reset breakers or reset the board, because a gate that got interrupted mid-cycle can slam on re-energize and strip teeth off the rack. After the release is disengaged, check your home breaker for the gate circuit. If the operator still won’t respond after power is restored, the board or a limit switch likely took the spike. Call (877) 610-2993 and we’ll diagnose it over the phone and then on site.
They do. Medway has open road frontage and lot layouts that leave gates exposed to sustained nor’easter winds. A solid wood or metal infill gate doesn’t allow wind through, so the entire wind load hits the operator’s arm, hinge welds, and the rack-and-pinion teeth on slide gates. If your gate faces an open stretch of road or field, size the operator for a heavier gate than the panel weight alone suggests. We factor that exposure into every operator replacement we quote in Medway. Call (877) 610-2993 to get a written estimate that accounts for your lot’s actual wind exposure.
Go outside and look at the gap between the gate edge and the hinge post at the top and bottom. If the gap is wider at the top, the post is leaning away. If the gap is consistent and the latch is tight, the panel or hinges are the problem. A post that’s heaving will also show a lifted concrete pad or a crack in the footing flange where it meets the post. In Medway, what feels like panel sag is usually post movement underneath it. If you want a free second opinion on any written estimate you already have, call (877) 610-2993 and we’ll come look.
Massachusetts follows the safety standard that any automated gate must reverse on contact and have a secondary entrapment protection device such as photo-eyes or an edge sensor. Medway does not have a separate town-specific gate code beyond the state standard. On our work, we will never disable a photo-eye or bypass a safety edge. If a previous repair left one bypassed, we’ll say so and bring it back to code. The ninety-day promise covers the whole installation, including safety devices. Call (877) 610-2993 to schedule a safety check or a repair, and the estimate is yours before any work starts.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Medway since 2001.