Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Heath
A broken gate in Heath usually means one of two things: either a wind storm off Lake Ray Hubbard finally bent a hinge post, or lake humidity ate through a connection that was fine last spring. We fix both, and we do it same-day for most calls in the 75032. Hal Gatewood has been repairing gates since 2001, and he sends a person, not a phone tree, to your driveway. Call (877) 610-2993 and a live person answers, any hour.
We know Heath’s gates because we work on them week in and week out. Custom wrought iron off Smirl Drive, slide gates on Falcon Point, cracked post footings in the clay along Horizon Road. The work here is different than Dallas or Plano. It’s the lake air and the wind. That’s not a sales line; it’s what we see when we pull up.
Why Gatewood Fence & Gate Is Heath’s Preferred Gate Repair Company
Most of our Heath customers found us after another company told them the gate needed to be replaced. We welded it back together in the driveway instead. There’s a difference between a company that sells gates and a shop that fixes them. We’re the second one. Hal’s name is on the shop, the shop has a published address, and he’s been at this since 2001. You can drive by and look him in the eye if you want to.
Heath homeowners call us because we understand what the lake does to gate hardware. The humidity off Lake Ray Hubbard is relentless. It gets into hinge bearings, into control board contacts, into backup battery compartments. A tech who only ever worked inland won’t look for that. We do, because we’ve seen it hundreds of times on this side of the county. When we quote a repair in Heath, that quote accounts for what Heath’s climate actually does, not what a generic service manual says.
Every job carries the 90-Day Done Right Promise in writing. Not “up to” 90 days, not “in most cases.” Ninety days, one call, and Hal comes back. That’s it.
Our Gate Repair Services in Heath
Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and that’s where we start in Heath. The clay soil here holds water after a hard rain, and when a 14-foot ornamental swing gate catches a 50 mph gust off open water, that force travels straight down through the leaf and into the post footing. The post rotates. The gate drops. Fix the panel without the post and you’ll fix it twice. We dig out the footing, reset the post with fresh concrete and rebar, and weld or shim the hinge bearings so the gate swings true.
Electric Gate Repair
Electric gates in Heath die in predictable ways. Lake humidity corrodes copper contacts on control boards, backup batteries sulfate early, and storm-driven power fluctuations take out capacitor packs. We diagnose the actual failure rather than swapping parts until something works. Hal stocks boards, capacitors, limit switches, and batteries for most Heath installs so we’re not waiting on a part from a warehouse in Ohio while your gate sits open.
Gate Realignment
Wind gusts off Lake Ray Hubbard load a solid infill swing gate like a sail. The leaf twists, the hinges bind, and the operator starts fighting its own track. We realign the gate on its new hinge bearings, re-plumb the posts, and recalibrate the operator’s limits so it stops slamming or stalling. If your gate groans every time it moves, the operator’s telling you something. Show me a gate closing on its own and I’ll show you where it’s failing.
Weld & Rust Repair
Rust along the bottom rail and hinge welds isn’t cosmetic on a Heath gate. The humidity feeds it, and a rusty weld is a fatigue crack waiting to happen. We grind the affected area down to clean steel, weld the stress cracks with on-site welding so the gate never leaves your driveway, and treat the rail so it doesn’t start again in eighteen months. No hauling your gate off to a fab shop. No telling you to buy new. Fix it where it hangs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Heath
We work on the operators Heath builders actually installed. FAAC and BFT show up on a lot of the custom estate gates off the lake, and Linear operators are common on the HOA entrances up and down Horizon and Smirl. We stock boards, remote receivers, and safety sensors for those brands so a repair call doesn’t turn into a two-week wait. If you have a different brand, call anyway. Hal’s certified on nine major brands and he’s seen most of what’s bolted to a post in Rockwall County.
Common Gate Repair Problems We See in Heath Homes
- Wind-twisted gate leaves. Solid ornamental gates off the water catch wind like a barn door. The leaf bends, the hinge pins oval out, and the gate starts dragging. We straighten leaves, sleeve hinge barrels, and reset post alignment.
- Sulfated backup batteries. That’s the quiet one. Gate works fine for two years, then a storm knocks out power and the gate won’t open even after the lights come back. The battery died months ago. Lake humidity accelerates sulfation; Heath batteries need checking more often than ones in Rowlett or Fate.
- Corroded control board contacts. The failure doesn’t look like corrosion. The gate just stops at the wrong limit some days, or opens an inch and reverses. Green fuzz on a contact. We clean or replace the board and seal the enclosure properly.
- Post footings gone soft. After ten days of rain, the clay around a post footing turns to soup. The gate settles, the operator works harder, and the overheating relay eventually trips. We rebuild footings bigger than the original spec so they hold.
Pricing for Gate Repair in Heath, TX
A hinge and post reset in Heath typically runs $425 to $700 depending on footing depth and whether we’re re-welding the hinge plates. Gate realignment runs $185 to $350. Electric gate troubleshooting and control board replacement falls between $240 and $520 for most residential operators. Weld and rust repair on a 12-foot ornamental leaf usually lands between $250 and $450. The price is quoted and agreed before any work starts, and there’s no trip charge inside the county. Seniors and veterans get a permanent 10% off, and any repair over $200 takes $40 off. If you have a written estimate from another company, bring it to us for a free second opinion.
We Also Serve Cities Near Heath
Most of our Heath work comes from referrals in Rockwall, Fate, Royse City, and Rowlett. If you’re a few miles down the road, we still come. Our Gate Repair team runs local routes through eastern Rockwall County every week, so scheduling near Heath doesn’t mean waiting for a one-off trip.
Serving Heath, TX - Our Local Coverage Area
We’re based in the Heath area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Heath
Yours probably caught a straight-line gust off open water, and the neighbors’ gates didn’t. Wind off Lake Ray Hubbard hits the shoreline without trees or buildings to break it up, so a solid infill gate becomes a sail. If your post footing was set shallow or the soil was saturated from rain before the wind hit, the post rotated and the gate pulled itself down. We see this pattern on lake-facing properties every spring. Call (877) 610-2993 and we’ll inspect the post and hinge bearings.
In Heath, nine times out of ten that’s a dead backup battery that sulfated from lake humidity months ago. The operator never switched over during the outage, and now the board’s locked out because it lost its memory. We test the battery, reset the board, and replace what’s failed. It’s one of the most common calls we get after a storm.
Yes, and it’s worse here than most of DFW. Lake-generated humidity keeps iron wet longer after rain and dew, so rust forms faster at the weld joints and rail seams. The bottom rail rusts first because water pools there. We grind, weld, and treat those areas, and we’ll tell you honestly whether the rail is worth saving or has lost too much section.
Moisture gets across the lens or into the photocell housing wiring. Near the lake, that humidity never fully dries out between storms, so the accumulation is worse than inland. The fix is usually a sealed housing and cleaned contacts, but sometimes the cell is cracked from hail and needs replacement. Call us and we’ll check it.
Most operators have a manual release handle or keyed release on the operator body. On slide gates, you’ll find a round handle or pull-chain behind the access cover. On swing gates, there’s usually a lever where the arm meets the gate. Pull the release, then push the gate slowly by hand. Do not force it: if the gate fights you, stop and call us. The gate may have a mechanical bind from wind damage. For any operator with high-tension springs or a counterweight, leave it alone and call (877) 610-2993. A trained professional should handle anything that stores energy.
Call (877) 610-2993 for gate repair in Heath. A live person answers, the quote is free, and the price is set before we start.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Heath since 2001.