Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Danville
Gate repair in Danville comes down to one thing: knowing what you’re looking at before you touch it. Most of the automated gates around here were hung between 1985 and 2005, which means the control boards are discontinued, the hinge posts are tired, and the wind off Mount Diablo has been working against the alignment for decades. We’ve been called out to Danville enough times to recognize the failure patterns by neighborhood. If your gate is sagging, stuck, or dead at the keypad, call (877) 610-2993 and a live person answers. We’ll be straight with you about what it needs and what it doesn’t.
Why Gatewood Fence & Gate Is Danville’s Preferred Gate Repair Company
Hal Gatewood started this shop in 2001, and his name is still on the door. That matters in Danville, where HOA-governed communities like Blackhawk expect a repair that matches the original gate profile and a person who stands behind the work. We don’t swap parts that don’t need swapping. We show up, diagnose the actual failure, and fix it in the driveway. Every job carries the 90-Day Done Right Promise in writing: if it’s not right, one call brings us back. No runaround.
Danville homeowners call us because their neighbor told them to. We’ve rebuilt hinge posts in 94506, retrofitted LimeMaster and Elite swing operators in 94526, and matched powder-coated finishes to HOA specs. You’ll get a background-checked, uniformed crew member on the job, and the person who answers the phone is a live human being, not a voicemail tree. Call (877) 610-2993 and you’ll hear a real voice, 24 hours a day.
Our Gate Repair Services in Danville
Electric Gate Repair
An electric gate that won’t open usually isn’t the motor. In Danville, we often find the failure upstream: a dead control board, a corroded connection in the operator housing, or a photocell that’s drifted out of alignment. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. We trace the circuit first, then quote you a price before any work begins.
Automatic Gate Repair
Automatic gates in Danville see a particular kind of wear because of the wind corridor through the San Ramon Valley. Swing arms work loose, limit switches drift, and keypads lose programming after Diablo wind events rattle the housing. We reset, rewire, and replace what’s actually broken. If the operator is obsolete, we’ll tell you plainly whether a retrofit board makes sense or whether a full replacement is the cheaper answer over five years.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and that is where we start. Many Danville homes built in the 1980s and 1990s have ornamental steel gates hung on undersized posts or footings that have rusted below grade. We dig, repair or replace the post, set a proper footing, and weld on site so the gate stays in your driveway. Fix the panel without the post and you’ll fix it twice.
Gate Realignment
Wind load is the quiet killer of gate alignment. Danville regularly gets hot, dry gusts above 50 mph out of the hills near Mount Diablo, especially in late summer and fall. Those loads push swing gates out of true, stress the leaf arms, and pull the post anchors loose over time. We realign the leaves, adjust the travel and force settings, and make sure the safety sensors sit where they’re supposed to for UL 325 compliance.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Danville
We’re certified on nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Danville customers, that means we usually have the common boards, arms, and sensors on hand or sourced same-week from local supply houses. If you’ve got an old Linear slide operator in 94506 or a BFT swing system in 94526, we can tell you over the phone what we’re likely walking into before we even roll the truck. Gate Repair is what we do every day, not a side line.
Common Gate Repair Problems We See in Danville Homes
- Obsolete control boards on 1980s-1990s operators in Blackhawk. The original LiftMaster and Elite boards are discontinued. We source compatible retrofit boards or walk you through a modern replacement that keeps the HOA profile intact.
- Wind-driven sag on ornamental swing gates. Diablo wind events push large gate leaves around constantly. The hinges and post anchors loosen faster than in sheltered East Bay areas, which shows up as scraping or a gate that won’t close fully.
- Failing hinge posts on 1980s-2000s builds. Undersized footings and below-grade corrosion mean the post moves before the panel does. A new hinge alone won’t fix it. We correct the post and the footing.
- Dead keypads and photocell faults after wind or rain. Moisture gets into older housings and the contacts corrode. We clean, reseal, and replace sensors with modern units that meet current entrapment protection standards.
Pricing for Gate Repair in Danville, CA
Straight numbers, because you deserve them before we show up. A typical hinge and post repair in Danville runs $325 to $650 depending on post condition and footing work. Gate realignment jobs usually land between $180 and $340. Electric gate troubleshooting and board replacement starts around $225 for a basic relay or limit-switch fix and goes to $700-$1,400 when the operator needs a retrofit board or full replacement. A new residential swing operator installed is typically $1,800-$3,200. We don’t charge a trip fee inside the county, we take $40 off any repair over $200, and veterans and seniors get a permanent 10% discount. The price is quoted and agreed before any work starts. Call (877) 610-2993 for an exact quote, and if you already have a written estimate from another company, bring it. We’ll give you a free second opinion.
We Also Serve Cities Near Danville
We run crews into Danville daily and cover the surrounding communities too. If you’re in Blackhawk, Moraga, San Ramon, or Alamo and your gate is giving you trouble, the same owner-operated team handles your call. Same live person on the phone, same 90-Day Done Right Promise on the work.
Serving Danville, CA - Our Local Coverage Area
We’re based in the Danville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Danville
Because the original control boards in 1980s and 1990s LiftMaster and Elite operators are discontinued, and the failure is in the logic board itself, not a replaceable relay. Repairing the board means finding a compatible retrofit or switching to a modern operator that can keep the gate profile HOA-compliant. In Blackhawk specifically, the HOA reviews gate appearance and setback, so the repair has to satisfy both the electrical and architectural sides. Call (877) 610-2993 and we’ll explain what your gate will actually need.
Diablo winds regularly exceed 50 mph in the San Ramon Valley corridor, especially in late summer and fall, and they push against large ornamental gate leaves every time they blow. That repeated load wears hinge pins, stretches leaf arms, and rocks the post anchors loose over time. What starts as a small sag turns into a gate that scrapes the driveway or won’t close completely. We reset the alignment and reinforce the points the wind attacks.
In many Danville communities, yes. HOA architectural guidelines in communities like Blackhawk specify gate styles, finishes, and setbacks, and a replacement that changes the look or position can trigger a review. A straight repair to the existing gate usually doesn’t require approval, but swapping the operator or changing the gate profile often does. We’ve done enough Blackhawk and 94526 work to know what’s likely to sail through and what needs a variance. Call (877) 610-2993 and we’ll walk you through it.
There’s no fixed schedule; the failure depends on the original footing and how much water and wind the post has seen. But if we’ve aligned the gate once and it’s sagging again within a year, the post or its footing is the problem, and replacing just the hinge is wasted money. Many Danville homes from the 1980s-2000s have posts set in undersized footings that rust below grade. We replace the post and correct the footing, and most of those repairs hold for the life of the gate. Estimates are free, so call (877) 610-2993 and we’ll tell you exactly what you’re dealing with.
Yes. UL 325 entrapment protection requirements apply to automated gates regardless of age, which means photocells or another monitored entrapment protection device are required by current safety standards. Many gates built in the 1980s and 1990s were installed without them or with sensors that have long since died. We retrofit modern safety photocells onto older operators so the gate is compliant and doesn’t close on a car, kid, or dog. This is standard work for us on Blackhawk retrofit jobs.
Need a gate looked at in Danville? Call (877) 610-2993 now. A live person answers, and we’ll set a time that works. The estimate is free, the price is fixed before any work starts, and every repair carries the 90-Day Done Right Promise in writing. Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Danville and the San Ramon Valley.