Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Culver City, CA
Gate repair in Culver City usually comes down to one of three problems: a hinge corroded by the marine layer, a post that was never set deep enough for the gate it’s carrying, or an operator board shorted by moisture creeping in through an old seal. Most repairs run between $175 and $520 depending on what’s actually failed, and we quote the exact price before any work begins. Call (877) 610-2993 and you’ll get a live person who can tell you what your gate is likely to need.
Why Culver City Homes Are Different
Culver City sits five to six miles from the Pacific, close enough that the marine layer rolls in most nights and hangs around until mid-morning. That persistent coastal humidity, plus trace salt air, pits iron and tubular steel hardware faster than you’d see a dozen miles east. Hinges seize, chain rusts stiff, and control boards corrode on gates that are only three or four years old. It’s not a one-time maintenance problem here; it’s a recurring reality.
The housing stock adds another layer. Most single-family homes in Culver City were built in the post-WWII and 1960s-70s boom, which means driveway gates were retrofitted onto existing posts rather than built as matched systems. We see non-standard clearances, mismatched hardware, and posts set in shallow footings that were never meant to hold a 300-pound steel gate. Then there’s Fox Hills, with its dense concentration of 1970s and 80s garden-style condo complexes where community vehicle gates cycle hundreds of times a day. Different problems, same zip codes.
Gate Repair in Culver City
Gate repair in Culver City means diagnosing what actually failed and fixing that, not selling you a whole new gate. Most jobs we see fall into a few categories: a hinge that’s corroded through, a post that’s shifted out of plumb, or an operator that’s given up after years of marine-layer exposure. We fix the gate in your driveway, weld on site where it’s needed, and leave you with a written 90-Day Done Right Promise. Our full Gate Repair service covers everything from a dragging gate to a full automation failure.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle. That’s where we start. In Culver City’s older housing stock, posts were often set for a small wooden gate and later asked to carry steel. The result is a post that’s shifted, stripped hinge bolts, and a gate that drags on the walkway. We cut out rusted hardware, weld new hinge plates where needed, and re-set posts so they actually hold. Hinge and post repair in Culver City runs $240 to $520 depending on how much of the post base is still sound.
Electric Gate Repair
When your electric gate stops responding to the remote or the keypad, the problem is usually the operator, the safety sensors, or the wiring running to the motor. In Culver City’s climate, salt and moisture creep into electrical connections faster than you’d think. We trace the circuit, test the motor, and replace only what’s actually failed. A typical electric gate repair in Culver City runs $195 to $420 depending on whether it’s a sensor, a board, or a full operator swap. The gate closing on its own is usually a failing loop detector or misaligned safety edge, not the motor, and we’ll show you why before we quote you.
Gate Realignment
A gate that’s started scraping the ground or hanging slightly crooked is giving you a warning. Ignore it and the hinges fail, the post stresses, and the operator burns out early. We realign the gate, adjust the hinges, re-tension the frame if it’s welded steel, and show you the corrected alignment before we leave. Most realignment jobs in Culver City run $175 to $340 and can be done the same visit as the inspection. If the post is the real problem, we’ll tell you that too, and fix it rather than re-hanging a gate on a foundation that’s already moving.
How much does gate repair cost in Culver City?
Gate repair in Culver City typically runs $175 to $520 depending on what failed. Hinge replacement starts around $90 per hinge, post repair runs $240 to $520, and electric gate board or sensor repair lands between $195 and $420. We quote the exact price before any work starts, and the number you agree to is the number you pay. Call (877) 610-2993 for a free estimate.
Can you fix my gate the same day in Culver City?
In most Culver City neighborhoods, yes. We can usually have someone at your gate the same day you call, often within a few hours. From the 90230 flatlands to the hills of 90232, we keep trucks stocked and a live phone on around the clock. Emergency calls, like a gate stuck open or seized closed, get priority. Call (877) 610-2993 and you’ll speak to a person, not a recording.
Gate Installation in Culver City
Gate installation in Culver City runs about $2,800 to $9,500 for most residential jobs, with swing gates on the lower end and custom sliding or security gates higher. The biggest variable isn’t the gate itself; it’s what’s already in the ground. Most Culver City driveway gates are retrofits, hung on posts that were poured decades ago for a different job. We measure what’s actually there and build to it, which is why our quotes hold. Learn more about Gate Installation and what a full job includes.
Driveway Gate Installation
Most Culver City driveway gates are retrofits. The house was built in 1958 or 1967, and someone added a gate long after the driveway was poured. That means non-standard clearances, odd post spacing, and hardware that was pieced together from whatever the last contractor had in his truck. We measure what’s actually there and build to it. A typical automated driveway gate in Culver City runs $3,200 to $7,800 installed, depending on width, material, and whether we’re adding an opener or tying into an existing one.
Sliding Gate Installation
Sliding gates are the workhorse of Culver City’s studio-adjacent properties and commercial lots. Sony Pictures on Washington Blvd, Amazon Studios, and the Apple TV+ facilities all sit inside Culver City, and the gate hardware on those campuses sees heavy daily cycles. For residential sliding gates, we spec V-track or cantilever systems based on the drive slope and how much debris collects. A residential sliding gate in Culver City typically runs $4,800 to $9,500 including a rack-and-pinion operator. Galvanized steel isn’t an upgrade here; it’s the minimum spec that lasts.
Security Gate Installation
If you have a wide driveway or want a true security barrier, double swing gates or a single heavy sliding panel are the honest answers. Culver City security gates on studio-adjacent streets often need card readers, loop detectors, and intercom tie-ins. We handle the full power run, the safety edges required under UL 325, and the access control integration. A custom security gate installation in Culver City runs $5,500 to $12,000 depending on steel gauge, automation, and the access system you choose.
How does Culver City’s coastal humidity affect which gate materials I should choose?
Coastal humidity in Culver City means you should choose galvanized steel posts, stainless fasteners, and sealed operator enclosures from day one. Paint alone won’t stop the salt air from eating through mild steel within a few years. The marine layer pushes constant moisture into hinges, posts, welds, and control boards, and inland-grade hardware fails well ahead of schedule here. Call (877) 610-2993 and we’ll walk you through the exact materials for your street.
Why do gate posts in Culver City’s older neighborhoods fail so often?
Gate posts in older Culver City neighborhoods fail because they were installed as plain steel set in shallow footings, and the persistent marine humidity rusts them through at the base within a few years. During a new installation, we pour proper concrete footings below grade, use galvanized or stainless posts, and seal the base where water collects. That’s the fix that lasts, and we check the post before hanging anything new.
Gate Motor & Opener in Culver City
A gate motor that quits in Culver City usually gives you a warning first: a slower open, a grinding sound, a gate that stops halfway and sits there. By the time it won’t move at all, you’re either parked on the street or backing up traffic on a narrow cul-de-sac in Blair Hills. The fix is usually straightforward for someone who works on these systems every week, and we stock parts for the brands most common on the Westside. Our Gate Motor & Opener service covers repair, replacement, and full installation.
Motor Repair
Most motor repairs in Culver City are the same five or six failures we see weekly: a gear worn to a nub, a logic board shorted by marine-layer moisture, a capacitor too weak to start, a limit switch out of adjustment, or a photo-eye knocked out of alignment. We show you the failed part and give you the honest choice: repair it, replace it, or rebuild it. Motor repair in Culver City usually lands between $260 and $580. Green fuzz on terminals is common here even on gates just three years old.
Motor Installation
Installing a gate motor in Culver City is rarely a bolt-on job, mostly because so many of the city’s 1960s-era driveways were poured with no thought of automation. The post may need reinforcement, the gate hinge may need to be re-pitched, and the operator arm may need a custom mount. We handle all of it, including the electrical run and safety edges, so the new motor isn’t just mounted; it’s right. A full installation on a single-swing driveway gate in Culver City typically runs $2,800 to $4,800, and we program the keypad before we leave.
Slide Motor Service
A slide motor failing on a steep-grade driveway in Culver Crest isn’t the same as one failing on a flat lot in Fox Hills. The grade loads the motor and gear plate differently, and we set chain tension and limit points accordingly. We install and service slide motors for both cantilever and rail-track gates, which covers most of what Culver City requires. Slide motor replacement here typically runs $850 to $1,700 depending on gate length and whether the chain and wheel trucks are still serviceable. Brand names we work on weekly include Linear, Viking, and DoorKing.
How fast can you get to Culver City for a gate motor problem?
Most Culver City calls are reached the same day, usually within a few hours. Our crews are stationed for the Westside, and Culver City is a normal part of the route. If your gate is stuck closed and you can’t get your car out, tell us that when you call (877) 610-2993 and we’ll prioritize you. A stalled community gate in Fox Hills is a security problem, and we treat it that way.
Is gate motor repair more expensive in Culver City than nearby?
Not meaningfully. Our labor rates and part prices are the same whether you’re in Culver City, Ladera Heights, or Venice. The marine-layer corrosion here does mean we’re sometimes replacing terminals and treating rust before we touch the motor itself, which can add $40 to $80 to a job. The estimate is free and there’s no trip charge inside the county, so there’s no cost to finding out what your gate actually needs.
Gate Access Control in Culver City
Gate access control in Culver City isn’t one-size-fits-all. The city’s mix of post-war single-family homes, hillside lots, condo communities, and working studio properties means the system on one block may be entirely different from the system three streets over. We work on keypads, phone entry, card readers, and intercoms across all four Culver City zip codes, and we’re comfortable around the proprietary commercial setups in the Hayden Tract. See Gate Access Control for the full scope of what we service.
Keypad Entry
A keypad seems simple until it isn’t. The marine layer that sits over Culver City most of the year pushes moisture into keypad housings, corroding contacts and causing intermittent failure long before the unit actually dies. We install and repair keypads rated for coastal exposure, and we mount them where condensation won’t pool inside the housing. A typical keypad replacement or new install in Culver City runs $350 to $750 depending on whether we’re adding a standalone unit or integrating it with your existing opener.
Card Reader & Proximity Systems
For commercial properties and some larger residential complexes in Culver City, card readers and fob systems control who gets in and when. The Hayden Tract and studio-adjacent buildings in the 90231 zip often use card access tied to employee databases and security logs. Those integrations matter for liability and insurance reasons. Card reader install or replacement in Culver City runs $450 to $1,100 depending on the controller integration required. We’re certified on Ghost Controls and DoorKing systems, among others.
Phone Entry Systems
Phone entry is the standard for most gated apartment and condo communities in zip codes 90230 and 90232. The system dials your phone when a visitor calls from the box at the gate, and you press a button to open it. When these systems fail, the problem is usually the phone line, the power supply, or a relay that’s been fried by the gate motor’s amperage draw. Phone entry repair in Culver City runs $180 to $450, including older units that many companies refuse to touch.
Do you handle access control on commercial gates near the studios?
Yes, we work on card readers, intercoms, loop detectors, and controllers along Washington Blvd and Hayden Avenue, including mixed-use properties with proprietary systems. Many of those gates need technicians who understand commercial access control, not just residential remote openers. We service the major brands and handle both sides of that demand in Culver City. Call (877) 610-2993 and describe the system; we’ll tell you whether it’s a job we can take on.
Is gate access control pricing in Culver City comparable to nearby cities?
Yes. Our pricing for Culver City is the same as what we charge in Ladera Heights, Venice, and Century City. The main cost differences come from the system type and the condition of existing wiring, not the zip code. Coastal moisture does mean some repairs require corrosion treatment that drier inland areas rarely need, and that work is included in the quote. Call (877) 610-2993 for a free estimate.
Gate Parts & Welding in Culver City
Gate parts and welding in Culver City usually means one of two things: a sagging hinge that’s finally given out after years of coastal humidity, or a broken weld on a steel frame that someone installed wrong the first time. We do both in your driveway, with a welding rig on the truck, so your gate never leaves your property. Our Gate Parts & Welding service covers hinge replacement, post repair, rail work, and custom fabrication.
Hinge Replacement
Culver City sits five to six miles off the Pacific, and that marine layer does not take a day off. Iron and tubular steel hinges here corrode noticeably faster than they do in drier Eastside LA. A residential gate hinge replacement in Culver City typically runs $180 to $390 depending on gate weight and whether the post plate needs reinforcement. We cut out the old hinge, treat the rust, weld in the replacement, and align it so the gate swings without dragging.
Post Replacement
Most driveway gates in Culver City’s post-WWII and 1960s-70s housing stock were added years after the house was built. The posts weren’t always set in concrete footings big enough for the job. When a post leans, the gate sags; when it rusts through at the base, the gate drops. Post replacement here runs $400 to $900 including excavation, new steel, concrete, and re-hanging the gate. We reuse the original gate panel if it’s sound, which is usually the case.
Custom Welding
Need a section fabricated that isn’t a stock part? We do custom welding for gate frames, stiffeners, latch boxes, and post extensions. Custom welding jobs in Culver City typically run $300 to $800 depending on material, complexity, and finish. We can also reinforce an older gate that’s twisting under its own weight. If your property has a gate with card readers and loop detectors around the Hayden Tract area, we’re comfortable working around that gear and will coordinate the welding with the access control so nothing gets fried.
Can you handle emergency gate welding in Culver City?
Yes. We answer calls around the clock and we prioritize gates that won’t close or won’t open. If a weld broke and the gate is hanging, call (877) 610-2993 and we’ll walk you through what to check over the phone. A partially supported gate can drop without warning. Don’t try to lift or force it. Keep people and pets clear until someone can assess it properly.
Do you fabricate parts that aren’t available off the shelf?
Yes, we fabricate hinge plates, stiffeners, post extensions, and latch boxes in our own welding setup, often the same day. Many older Culver City gates have non-standard dimensions that stock parts won’t fit. We measure what’s there, cut and weld to match, and finish the work so it blends with the rest of the gate. Call (877) 610-2993 for a free estimate on custom work.
Brands We Service in Culver City
We’re certified to service nine major gate brands, and in Culver City we see a steady rotation of Linear, Ghost Controls, Viking, and DoorKing operators on residential and commercial gates. We stock common boards, arms, and remote kits for these brands on the truck, which means most repairs don’t wait on a parts order. See our brands for the full list.
Pricing for Gate Repair in Culver City, CA
| Service | Typical Range in Culver City |
|---|---|
| Gate realignment | $175 - $340 |
| Hinge replacement (per hinge) | $90 - $180 |
| Post repair or reset | $240 - $520 |
| Electric gate board or sensor repair | $195 - $420 |
| Motor repair | $260 - $580 |
| Keypad replacement or new install | $350 - $750 |
| Phone entry repair | $180 - $450 |
| Card reader install or replacement | $450 - $1,100 |
| Weld & rust repair (per section) | $120 - $300 |
| Full operator replacement | $650 - $1,400 |
What pushes the price up in Culver City is usually post condition and corrosion. Older retrofit posts often need re-setting before a new gate or motor can go on, and that work is honest, necessary labor, not an upsell. The price we quote on the phone or in writing is the price you pay, agreed before any work starts.
Neighborhoods We Serve in Culver City
We cover every zip code in Culver City, 90230 through 90233, and most of our calls come from these neighborhoods. Same-day service is available across the area, and a live person answers the phone around the clock.
- Culver Crest - hillside driveways with steep grades and older retrofitted gates
- Blair Hills - custom residential gates on varied terrain
- Fox Hills - 1970s and 80s condo complexes with heavy-use community gates
- Hayden Tract - mixed-use commercial properties with access control systems
- McManus - post-war homes where driveway gates were added later
Service Area - Cities Near Culver City
We also serve the communities around Culver City, CA, including Ladera Heights, CA, Century City, CA, Venice, CA, Beverly Hills, CA, and View Park-Windsor Hills, CA. Dispatch and scheduling are coordinated from the brand’s Los Angeles office, and crews serve Culver City locally.
Serving Culver City, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Culver City and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Culver City coverage area; if your address is on it, we can help.
Also serving nearby: Culver City, CA, Ladera Heights, CA, Century City, CA, Venice, CA, Beverly Hills, CA, View Park-Windsor Hills, CA.
FAQs About Gate Repair in Culver City
Most gate repairs in Culver City don’t require a permit, but installing a new automated gate or running new electrical may trigger city requirements depending on the scope. We’ll tell you during the estimate whether your specific job needs anything from the city, and we handle the paperwork when it does. Call (877) 610-2993 and describe the project.
Yes, we service commercial sliding gates and access control on properties near Sony Pictures, Amazon Studios, and the Apple TV+ facilities. Those systems are heavier, cycle more often, and often integrate card readers and loop detectors. We’re certified on the major commercial brands and we handle both sides of that demand in Culver City.
Call (877) 610-2993 and tell us what the gate is doing. A live person answers around the clock, and we’ll give you a straight answer about what it’s likely to take and when we can be there. Most Culver City neighborhoods get same-day service, and every estimate is free with no trip charge inside the county.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Culver City Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg