Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Bronxville
Gate repair in Bronxville almost always means working on wrought iron that was forged before World War II. Most of the village’s residential gates are original ornamental iron hung from stone or brick pillars built between 1895 and 1940, so the job is rarely a simple hardware swap. It’s matching scrollwork, resetting hinge anchors into century-old masonry, and knowing when a legacy operator can be saved versus when it’s quietly becoming a safety hazard. Hal Gatewood has been doing exactly this kind of work since 2001, and when you call (877) 610-2993, a real person answers. Usually Hal himself.
Why Gatewood Fence & Gate Is Bronxville’s Preferred Gate Repair Company
Bronxville homeowners tend to ask the same two questions before anyone touches their gate: can you match the original ironwork, and will you show up when you say you will. The answer to both is yes, and that’s not a sales pitch. Hal Gatewood’s name is on the shop and on every invoice. The address is published. The license number is something anyone can look up. When we say we’ll be there Tuesday between nine and eleven, the person who shows up is Hal or one of his crew, background-checked and in uniform, driving a truck with the company name on the door.
We’ve been repairing gates in Bronxville long enough to know the Lawrence Park hill section gets worse frost heave than the flatter streets near the school. We know the difference between an original Tudor Revival gate on a Pondfield Road estate and a later addition that never matched the house to begin with. And we know that a gate sagging at the hinge post in Bronxville is almost always a masonry anchor failing, not a hinge pin wearing out. That local knowledge means we diagnose faster and fix it once. Our Gate Repair team has built its reputation in this village one driveway at a time, and neighbors talk.
Our Gate Repair Services in Bronxville
Weld & Rust Repair
Most Bronxville gates are 80 to 100 years old, which means decades of rust at forge-welded decorative joints and corroded hinge pins inside masonry anchors. We weld on site, in your driveway. The gate never leaves your property. Hal matches the original picket profile and scrollwork pattern, cuts out the rotted section, and forge-welds in new iron that’s shaped and textured to match. When we’re done, you shouldn’t be able to point to the repair without looking closely. If you can, we haven’t done it right, and the 90-Day Done Right Promise means we come back.
Hinge & Post Repair
Fix the panel without the post and you’ll fix it twice. That’s the rule with Bronxville’s century-old pillar entries. The hinge post is where the entire gate hangs, and when the stone or brick pillar around those hinge anchors starts to crack, the gate will sag no matter how many times you tighten bolts. We cut out the old anchors, repair the masonry, and reset the hinges so the gate swings true. On sloped lots in the hill sections, we’ll often pour a new concrete pier below frost depth so next winter’s ground heave doesn’t undo this spring’s repair.
Gate Realignment
A gate sags in the hinge post, not in the middle, and that is where we start. Westchester freeze-thaw cycles heave post footings and throw swing clearances out of alignment. Your gate that closed cleanly in October starts scraping the latch post by February. We reset the post, rehang the gate, and adjust the hinges so the reveal is even across the full swing. Then we recalibrate the operator’s limit switches so the gate closes square instead of humming against the stop. This is the most common call we get from Bronxville homeowners right around March, after the ground gives up its winter shift.
Automatic Gate Repair
Legacy operators from the 1990s and 2000s are everywhere in Bronxville, and they fail in predictable ways. Control boards corrode, limit switches drift, safety photocells go dead without anyone noticing, and the operator starts fighting the gate instead of driving it. We service operators from FAAC, BFT, Linear, and Viking, among others. On an original wrought iron gate, we’ll always look at whether the existing operator can be retrofitted with modern safety sensors before we recommend replacing it. Sometimes retrofitting is cheaper. Sometimes the old board is obsolete and replacement is the honest answer. Either way, you’ll know the real cost before we start.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bronxville
We’re certified to service FAAC, BFT, Linear, and Viking operators, along with five other major brands. Because we see so many legacy FAAC and BFT units on Bronxville’s original gates, we keep common boards, limit switch assemblies, and photocell parts in the truck. That means we’re not driving back to a warehouse while your gate hangs half-open. For a 20-year-old Linear on a Pondfield Road driveway or a BFT that’s been shimming itself open on a Lawrence Park slope, we can usually diagnose and repair in one visit. If a part has to be ordered, we tell you that before any work begins, and you approve the price first. No surprises at the door.
Common Gate Repair Problems We See in Bronxville Homes
- Frost-heaved posts on sloped lots: The freeze-thaw cycles that roll through Westchester every winter push stone pillar footings out of plumb. Gates that cleared the ground in September drag by February, and the fix is resetting the post below frost depth, not cranking the hinge bolts.
- Rusted forge welds at decorative joints: Century-old scrollwork corrodes where the original blacksmith joined the pieces. These joints crack, then the decorative element starts vibrating loose and eventually snaps. Panel-only repairs can’t fix this; the ironwork has to be welded.
- Obsolete operator control boards: Bronxville still has plenty of 1990s and 2000s automatic gate operators running original boards. When those boards fail, they often fail intermittently. Worse, many of them predate modern safety photocell and loop detector requirements, which is a real safety concern on a gate that weighs several hundred pounds.
- Cracked masonry around hinge anchors: When the stone or brick around a hinge post anchor cracks, the gate sags and the hinge pulls out of the wall. Tightening the lag bolts just chews up the mortar further. The repair is cutting out the loose material, setting a new anchor, and rehanging the gate level.
Pricing for Gate Repair in Bronxville, NY
You should know what things cost before you pick up the phone. A typical hinge and post repair on a Bronxville wrought iron gate runs $400 to $900, depending on how much masonry has to be cut out and reset. Gate realignment, when the post is sound and it’s a matter of adjusting hinges and operator limits, usually lands between $250 and $500. Weld and rust repair on decorative scrollwork is the hardest to quote blind: small joint repairs start around $300, and a full picket profile match with multiple welds can run $600 to $1,400 depending on how much iron has to be replaced. Automatic gate operator repair on a FAAC or BFT unit typically runs $350 to $800, and a full operator replacement with new safety sensors lands between $1,200 and $2,800 installed. Every price is quoted and agreed before we touch the gate. Estimates are free. There’s no trip charge inside the county.
We Also Serve Cities Near Bronxville
Beyond Gate Repair in Bronxville, we regularly work in Tuckahoe, Eastchester, Mount Vernon, and Yonkers. Same standard, same crew, same 90-Day Done Right Promise. If you’re one town over in Eastchester or up the hill in Tuckahoe, call (877) 610-2993 and we’ll get you on the schedule. The company was founded in 2001 and has been owner-operated every day since, which means the person you talk to on the phone is connected to the person who does the work.
Serving Bronxville, NY - Our Local Coverage Area
We’re based in the Bronxville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Bronxville
Yes, we can match the original picket profile. We forge and shape the replacement iron on site to match the existing scrollwork, picket spacing, and texture. The goal is a repair you can’t find without someone pointing to it. Hal has been matching period ironwork since 2001, and in a village like Bronxville where the historic character is the whole point, we don’t install off-the-shelf panels and call it done. Call (877) 610-2993 and we’ll come look at the gate in person.
Most cracked pillars around hinge anchors are repairable without a full rebuild. We cut out the loose mortar and fractured stone, set new galvanized anchors in a proper concrete fill, and rehang the gate. The pillar only needs rebuilding if the structural stones themselves have shattered, which does happen on 100-year-old pillars that have been through decades of freeze-thaw heave. We’ll tell you which one you have before we start, and you’ll know the price either way.
Your gate is sagging because the post footing is moving, not because the hinges are loose. Freeze-thaw cycles in Westchester push the post out of plumb, and every tightening just masks the shift until the next cycle. We reset the post below frost depth, repair the masonry around the anchors, and rehang the gate so it stays square. Tightening hinges on a heaving post is like re-leveling a table on a sinking floor. Call (877) 610-2993 and we’ll fix the footing, not the symptom.
It depends on the board and the condition of the gearbox. If your operator is a 1990s FAAC or BFT with a dead control board but a solid motor and gearbox, retrofitting with a new board and safety photocells usually runs $350 to $800. If the gearbox is worn and the board is obsolete, replacement with a new operator and sensors installed runs $1,200 to $2,800. We always give you both numbers before any work starts. The quote is free, and it’s quoted before we touch anything.
No, not if it’s installed correctly. The operator drives the gate through the hinge point, and we set the force, speed, and limit switches to match the gate’s weight and swing. On an original wrought iron gate, we’re careful to keep forces low and run modern safety photocells and a loop detector where appropriate. We also set the limit switches precisely so the gate closes square without slamming into the latch post. On a sloped lot near the Lawrence Park hill section, our crew reset a heaving driveway swing gate whose original FAAC operator had been shimming itself open for years. We cut out the rotted hinge post footing, poured a new concrete pier below frost depth, rehung the gate with the exact scrollwork profile matched, and recalibrated the operator’s limit switches so it locks square without humming against the stop. Call (877) 610-2993 for a free estimate on your gate.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Bronxville since 2001. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.