Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Woodburn
If your gate is sagging, leaning, or won’t latch, the problem is almost never the whole gate. It’s a part. A hinge post that heaved out of plumb. A rail that rotted where it meets the stile. A hinge pin that’s been grinding metal-on-metal since 1987. In Woodburn, most of the gates we see were built alongside the houses, back in the 60s and 70s, which means the parts are failing not one at a time but all at once. We fix the parts, weld what’s cracked, and reset what’s shifted, right in your driveway. Hal Gatewood has been doing this since 2001. Call (877) 610-2993 and a live person answers, 24/7.
Why Gatewood Fence & Gate Is Woodburn’s Preferred Gate Parts & Welding Company
We’re not a national outfit with a rotating cast of subcontractors. Hal Gatewood’s name is on the shop and on every invoice, and his address is published. That’s the oldest accountability there is. Woodburn homeowners tell us the same thing over and over: they called a company that quoted one price on the phone, then a different guy showed up with a different number. We don’t work that way. The price is quoted and agreed before any work starts, in writing.
Our crew knows the 22047 ZIP. We know the split-levels off Spicer Street, the Cape Cods near the Holmes Run Stream Valley Park, and the colonial-style lots tucked along Woodburn Road. We know which HOAs require architectural approval before a hinge swap and which don’t. And we carry parts for the brands we service, so we’re not waiting on a truck from three states away. Dispatch is coordinated from our Washington, DC office; the person who shows up at your gate lives in the region and knows the clay soil, the freeze-thaw cycle, and the county code.
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Hal back. No runaround. We also answer the phone with a live person around the clock, not a voicemail or a chatbot. For Woodburn, that matters because a gate that won’t close isn’t an inconvenience. It’s a security problem.
Our Gate Parts & Welding Services in Woodburn
Hinge Replacement
Most Woodburn swing gates hang on hinges that have been on the post since the original install. We regularly replace those with stainless steel hardware sized and finished to match what the HOA approved. If the hinge post itself has shifted, we don’t just swap the hinge and call it done. A gate sags in the hinge post, not in the middle, and that is where we start.
Post Replacement
This is the single most common repair we do in Woodburn. Northern Virginia’s Piedmont clay expands and contracts through winter freeze-thaw cycles, and after 50-plus years, that movement cracks footings and pushes posts out of plumb. The panel looks fine, so the gate keeps sagging no matter how many times the hinges are tightened. We dig out the old footing, pour a new 30-inch-deep concrete base with gravel drainage, reset the post, and re-hang the original panel. Fix the panel without the post and you’ll fix it twice.
Rail Repair
Wooden privacy gates in Woodburn are typically frame-and-rail construction, and the humid summers here accelerate rot where the rail meets the stile. When the rail rots, the whole gate loses its shape, the latch stops lining up, and the gate starts dragging on the ground. We replace the rotted rail, reinforce the corner joints, and re-square the frame before re-hanging. In many cases we can save the original panel, which matters when an HOA wants a like-for-like match.
Custom Welding
When a part isn’t made anymore, or when an HOA requires a specific iron profile that’s no longer manufactured, we weld it on site. That means your gate stays in your driveway. We fabricate custom hinges, latch mounts, drop rods, and decorative ironwork. For gated community entrances in Woodburn with custom slide gates, we weld frame repairs and reinforce stress points without removing the gate leaf from the property.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Woodburn
If your Woodburn Gate Motor & Opener has a nameplate that says Viking, Ghost Controls, DoorKing, or Elite, we service it. We’re certified on nine major brands and stock common replacement parts locally, so a Woodburn repair doesn’t sit idle while parts ship from across the country. Most hardware repairs on these brands use standard components we keep on the truck. That means one trip, not three.
If you need parts or welding for any of these systems, call our Gate Parts & Welding team. A real person answers, and we’ll tell you if it’s a part we can bring today or if it needs to be ordered.
Common Gate Parts & Welding Problems We See in Woodburn Homes
- HOA approval delays. Here’s a scenario we see too often in Woodburn: a homeowner replaces a swing gate hinge without board sign-off, then gets a violation notice because the new hardware isn’t the approved black wrought-iron finish. We know which communities require architectural review and build the approval window into the quote so you don’t get caught.
- Post footing rot from Piedmont clay. Freeze-thaw cycles heave 50-year-old wooden hinge posts out of plumb. The gate looks fine, but it won’t close. We reset the post, not the hinge.
- Shared entry system conflicts. Gated communities in Woodburn use loop detectors or keypad entry. When a homeowner welds a new gate frame without re-aligning the safety photocell, the whole community’s operator goes into fault mode. We coordinate with the management company before touching shared equipment.
- Iron rust on older wrought-iron gates. Humid summers here accelerate rust on iron hardware, especially hinges and latch mounts that sit in morning shade near the houses. We cut out the rusted section, weld in new steel, and treat the repair to match the existing finish.
Pricing for Gate Parts & Welding in Woodburn, VA
Honest numbers, the way Hal gives them over the phone. A hinge replacement on a standard wooden swing gate in Woodburn typically runs $180 to $340 per hinge, including hardware and alignment. A full post reset with new concrete footing runs $450 to $850 depending on access and whether it’s a shared post on a double gate. Rail repair runs $225 to $500 per rail, and custom welding is $95 per hour plus materials, with most small fabrication jobs running $150 to $400 total.
Two things we want you to know. First, the price is quoted and agreed before any work starts. It does not change at the door. Second, every job carries the 90-Day Done Right Promise in writing. Standing offers: $40 off any repair over $200, free second opinion on any written estimate, no trip charge inside Fairfax County, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Woodburn
Our Gate Parts & Welding in Woodburn service area covers the 22047 ZIP and the surrounding communities. We’re also out in Woodburn-adjacent areas like West Falls Church, Merrifield, Annandale, and Mantua. If your gate is in any of those neighborhoods, the same crew, same pricing, same guarantee applies.
Serving Woodburn, VA - Our Local Coverage Area
We’re based in the Woodburn area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Woodburn
Yes, in many Woodburn communities, even a hinge swap requires Gate Access Control - Woodburn architectural review board sign-off if the new hardware differs from the approved finish. Fairfax County requires a building permit for any gate structure over 4 feet tall, but the HOA layer is stricter: boards mandate specific gate styles, heights, and hardware finishes, and they often reject like-for-like replacements if the original wood grain or iron profile isn’t matched. Some HOAs don’t require review for hardware-only repairs, but we’ll help you confirm before we touch anything. Call (877) 610-2993 and we’ll tell you what your specific HOA requires.
Because the hinge post is moving in the Piedmont clay, not the hinge itself. Freeze-thaw cycles in Woodburn’s soil expand and contract the ground under the footing, and after enough winters, the post loses plumb. Tightening the hinge or replacing it doesn’t fix the footing. The post has to be reset. We dig out the old base, pour a new 30-inch-deep concrete footing with gravel drainage, and re-hang the panel. Fix the panel without the post and you’ll fix it twice. Call (877) 610-2993 and we’ll look at your footing for free.
Yes. We fabricate and weld custom slide gates on site, including frame reinforcements, stress-point repairs, and custom iron profiles. Before any fabrication, we coordinate with the management company and the HOA’s architectural board to confirm the approved style, height, finish, and hardware profile. That approval window is typically 2 to 4 weeks in Woodburn, and we build it into the timeline so you don’t get a violation notice. Call (877) 610-2993 for a free measure and a written price.
Most of the time, it’s a misaligned safety photocell or a loop detector that’s picked up interference from a welded repair that shifted the frame. When a gate operator reverses without a visible obstruction, the safety circuit is reading something it shouldn’t. We test the photocell alignment, check the loop detector sensitivity on brands like Viking, Ghost Controls, and DoorKing, and re-align the frame if a prior repair moved anything. It’s usually a quick fix, not a new operator. Call (877) 610-2993 and describe what’s happening; we’ll tell you over the phone if it sounds like a safety-edge issue or a board problem.
No. This is one of the most common calls we get in Woodburn, and it’s almost always the frame, not the gate. Rain swells the wood, the frame shifts, and the latch no longer lines up with the strike plate. We re-square the frame, replace the rotted rail if we find one, and re-hang the panel so the latch catches clean. In most cases the original gate is worth keeping far longer. Call (877) 610-2993 for a free estimate; we’ll tell you if the panel is worth saving.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Woodburn since 2001.