Gate Parts & Welding in Union - Made to Measure, Written Price

Fast, Reliable Gate Parts & Welding Across Union

Gate installation in Union usually comes down to two things: finding someone who will actually repair the original gate instead of pushing a full replacement, and getting that work done without losing vehicle access for days. Gatewood Fence & Gate has been fixing gates on Union’s post-war side yards and Route 22 commercial properties since long before most of those hinges were considered old. Hal Gatewood answers his own phone at (877) 610-2993, and the person who quotes your job is the same person who shows up with a welder in the truck. If your gate is sagging, seized, or jumping its track, we’ll tell you straight what’s worth fixing and what isn’t.

Call (877) 610-2993

Why Gatewood Fence & Gate Is Union’s Preferred Gate Parts & Welding Company

We’re not a franchise outfit that sends a different tech every visit. Hal Gatewood started this shop in 2001, and his name is on every invoice. That matters in Union, where the housing stock was built in one tight window after WWII and the gate failures we see repeat block after block. A company from out of town might see a rusted hinge and quote a full gate replacement because they don’t weld on site. We see the same hinge on a Vauxhall Road split-level, a Galloping Hill Road cape, and a side street off Morris Avenue, and we fix it in the driveway.

Union customers call us because the phone rings and a person answers, not a queue. Hal or one of his crew will be there in the window promised, with a published shop address and license number anyone can verify. Our Gate Parts & Welding in Union work carries the 90-Day Done Right Promise in writing: if it isn’t right, one call brings us back. No runaround. No fine print.

We’re certified to service Gatewood’s nine brands including Linear, Viking, and DoorKing Union gate motor & opener hardware, which covers most of the original gate operators still running on Union’s older properties. And for the person who’s been burned before by a national outfit quoting one price on the phone and another at the door: our price is agreed before the first cut or weld, every time.

Our Gate Parts & Welding Services in Union

Most of what we do in Union is repair-first. A gate sags in the hinge post, not in the middle, and that’s where we start. Fix the panel without the post and you’ll fix it twice. Our Gate Parts & Welding team covers the full range, but these four services account for the bulk of our Union calls.

Hinge Replacement

Original galvanized hinge barrels on Union’s 1950s and 1960s gates seize from decades of road salt and freeze-thaw cycling. When a hinge pin snaps on a side-yard swing gate, the gate drops and the latch misses the strike. We cut out the old hinge, weld new barrels onto the original gate frame, and re-hang the panel so the operator’s safety photocell aligns without re-shimming. Typical hinge replacement in Union runs $180-$340 depending on gate weight and whether both hinges need replacement.

Post Replacement

Concrete post footings heave unevenly in Union’s freeze-thaw belt, especially on narrow shared driveways where runoff collects at the post base. A heaving post pulls the entire gate frame off-plumb, and no latch adjustment fixes that. We cut out the old footing, dig below frost line, re-set the post in concrete, and wait for the pour to cure before re-hanging the panel. In Union, a full post replacement with footing runs $450-$850 for a standard residential swing gate, more if the post is embedded in a masonry wall or carries an operator arm.

Rail Repair

Rusted-through bottom rails are common on Union’s original ornamental iron gates, especially where snow piles against the gate all winter. We cut out the rotted section, weld in new rail stock matched to the existing profile, grind the seam smooth, and re-coat the repair so it holds. Rail repair runs $150-$400 in Union, and we always tell you if the corrosion is widespread enough that patching no longer makes sense.

Custom Welding

Some repairs need a piece that was never a stocked part, and Union’s older gates are full of them: rounded corner brackets, decorative finials, custom latch plates. We weld on site from the service truck, so the gate stays in your driveway and you keep using your vehicles. Custom welding in Union starts around $150 for small brackets and runs up from there based on material and shop time. We’ll quote it before we strike an arc.

Trusted Brands We Service in Union

We’re certified on gate access control in Union for the operators and hardware most common on local properties: Linear, Viking, and DoorKing show up constantly on the original 1970s and 1980s installations along the Route 22 corridor and in residential side yards. We stock local parts for these brands so a repair doesn’t sit for a week waiting on a regional distributor. If your opener or gate hardware is a brand we don’t carry, we’ll tell you up front and point you to the right fix rather than sell you something that doesn’t match.

Common Gate Parts & Welding Problems We See in Union Homes

• Seized original galvanized hinge barrels: Decades of road salt thrown up by snowplows along Union’s side streets plus freeze-thaw cycles corrode the barrel from the inside. The pin seizes, then snaps, and the gate drops. We replace the hinge set and re-hang the panel same visit.
• Heaving concrete footings on shared driveways: Union’s narrow lots mean many side-yard gates sit on shared rights of way where runoff has nowhere to go. The footing heaves, the post tilts, and the gate drags. Re-setting the post below frost line is the only permanent fix.
• Slide-gate track channel failure on Route 22 properties: The heavy sliding security gates installed on Union’s commercial strip in the 1970s and 1980s sit on concrete-embedded bottom track channels that have heaved and cracked over decades. Rollers jump the track and bind the rack-and-pinion drive. We re-level the channel or weld in new track as needed.
• Original wrought iron gate frames rusting through at the bottom rail: Snow piles, splash-back, and decades of New Jersey weather eat the bottom rail first. We cut out and weld in new rail stock, matching the existing profile so the repair disappears.

Here’s the thing that’s specific to Union: the residential gates were installed in one compressed building boom between 1945 and 1970. That means Union’s gate technicians see the same failures across the whole town at once, and we’ve dialed in the fixes. Newer neighboring towns like Springfield or Kenilworth don’t have this same age-concentrated hardware stock, which is exactly why an outfit that works mostly in new subdivisions will misjudge a Union gate’s repair.

Pricing for Gate Parts & Welding in Union, NJ

We Also Serve Cities Near Union

Our Union crews cover the surrounding area too, including Kenilworth, Hillside, Roselle Park, and Maplewood. If you’re in one of those towns with an original iron gate that’s finally giving out, we’ll come look. Same pricing, same written promise, same person answers the phone.

FAQs - Gate Parts & Welding in Union