Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Sunset
If your gate in Sunset is sagging, dragging, or won’t close after the last storm, the fix usually comes down to one thing: getting the right parts welded by someone who understands Miami-Dade codes, not just someone with a truck and a welder. Gate parts and welding in Sunset mean hinge replacements, post resets, custom rail repairs, and ground-level corrosion fixes on gates that have been standing since the 1980s. Hal Gatewood has been welding and repairing gates since 2001, and the work happens at your driveway, not some warehouse across the county. Call (877) 610-2993 and a live person picks up, day or night.
Why Gatewood Fence & Gate Is Sunset’s Preferred Gate Parts & Welding Company
Sunset homeowners see a lot of gate repair companies come and go. Ours has been under the same name, same phone number, and same owner since 2001. Hal Gatewood’s name is on the shop and on every invoice, and the address is published for anyone who wants to look it up. Around Sunset, people recognize the truck and they know the person who shows up won’t be a subcontractor three counties away. When a gate stops working on SW 72nd Street or near Sunset Park, the response comes from our Miami office, with crews that work this corridor every week.
Reviews from Sunset customers keep pointing at the same things: the person on the phone knew what a pivot sleeve was, the crew showed up in the window they gave, and the quote matched the bill. We follow the same rule on every job in the 33173 ZIP: the price is quoted and agreed before any work starts, then it’s written down. Every repair carries our 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back. No runaround, no fine print.
Our Gate Parts & Welding Services in Sunset
Most gates in Sunset don’t need replacing. They need the right part welded back on, a post reset, or a hinge that actually fits. That’s what we do. Here are the four jobs we handle most in this area.
Hinge Replacement
Sunset’s older ornamental iron gates lean on hinges that were installed thirty or forty years ago, many of them set into concrete columns that have since cracked or shifted. We replace hinge pins, weld new hinge plates, and reset the alignment so the gate swings true instead of scraping the driveway. Hinge replacement on a single swing gate in Sunset typically runs $220-$490, depending on gate weight and whether the post needs reinforcement.
Post Replacement
In Sunset, the failure usually starts underground. Clay-heavy soil holds water, the water table sits high, and ground-level steel corrodes from the inside out. A post that looks fine above ground can be rusting through below it. We dig out the old footing, weld or set a new post, and pour a proper concrete base that will hold in saturated soil. Post replacement in Sunset generally costs $380-$750 for a standard residential swing gate post.
Rail Repair
Hurricane gusts bend top rails and crack weld joints at the hinge post, and every rail repair in Sunset has to match Miami-Dade NOA wind-load ratings. We cut out the damaged section, weld in matching material, and grind it smooth before repainting. A typical ornamental iron rail repair in Sunset runs $180-$350, and we match the finish so the patch doesn’t stand out like a Band-Aid.
Custom Welding
Sometimes the part doesn’t exist anymore, or it existed once and the manufacturer stopped making it. We weld custom brackets, hinge plates, gussets, and rail sections on site, in your driveway, so the gate never leaves your property. Custom welding work in Sunset starts around $150 for small brackets and runs up from there based on materials and time. We’ll tell you the price before the welder strikes an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Sunset
We service and carry parts for the operators and hardware Sunset homeowners actually have: Viking, Ghost Controls, and DoorKing show up constantly in the 33173 ZIP. If your gate motor is older and the manufacturer has moved on, we can usually find a compatible part or fabricate a bracket that makes it work. That’s the difference between a repair and a replacement sale. For our full Gate Parts & Welding team, the goal is to keep your existing gate functioning, not to sell you a new one.
Common Gate Parts & Welding Problems We See in Sunset Homes
- Wind-load damage on solid infill gates. Sunset sits squarely in Miami-Dade’s wind zone, and solid-panel gates catch storms like a sail. We regularly see top rails bowed, weld joints cracked, and hinges pulled out of the post after a hurricane or strong tropical storm passes through. Repairs have to match NOA wind-load ratings, which is a code requirement that doesn’t apply one county north in Broward.
- Ground-level corrosion at the pivot sleeve. Sunset’s clay-heavy soil and high water table trap moisture at the base of iron gates. The sleeve that holds the pivot pin rusts through from the inside even when the paint job looks intact, and the whole gate starts to lean or seize. We probe that area first on any pre-2000 iron gate in this ZIP.
- Shifting post footings after heavy rain. A week of tropical downpours saturates the soil under gate posts, and footings that were poured shallow in the 1980s shift. The gate drags, the latch misses, and the operator strains until it burns out. We reset the post with a deeper footing and proper drainage so it stays put.
- Failed operators running on degraded wiring and seals. South Florida humidity eats rubber seals, capacitors, and low-voltage wiring faster than any northern climate. Operator failures in Sunset are often electrical, not mechanical, and diagnosing that correctly saves you from replacing a motor that just needed a new capacitor and a sealed junction box.
Pricing for Gate Parts & Welding in Sunset, FL
Gate parts and welding in Sunset are priced by the job, not by the hour, and you’ll hear the number before we start. Hinge replacements land between $220 and $490. Post replacements run $380 to $750 including new concrete. Rail repairs are usually $180 to $350. Custom welding starts at $150 for small fabrications. If the repair exceeds $200, take $40 off. Seniors and veterans get a standing 10% discount on every job. Estimates are free, and there’s no trip charge inside the county.
We Also Serve Cities Near Sunset
Our crews cover the surrounding communities, including Olympia Heights, Westwood Lake, Richmond Heights, and Kendale Lakes. The same NOA-compliant parts, the same on-site welding, and the same 90-Day Done Right Promise apply to every job. For residents throughout Miami-Dade, we’re the local Gate Parts & Welding in Sunset crew that shows up when we say we will.
Serving Sunset, FL - Our Local Coverage Area
We’re based in the Sunset area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Sunset
Yes, in most cases it does. Miami-Dade’s post-Hurricane Andrew Notice of Acceptance requirement applies to structural gate hardware replacements in the 33173 ZIP, so a hinge post or gate roller job that changes the gate’s structural hardware typically requires a permit and an NOA-compliant part. We handle the paperwork and confirm product approval before we start, then quote the permit fee as a line item. It’s a Sunset-specific requirement that neighboring Broward County doesn’t impose. Call (877) 610-2993 and we’ll tell you whether your job needs it.
Because the post shifted in saturated soil. After heavy rain, Sunset’s clay-heavy ground turns soft, and older footings poured in the 1980s can settle unevenly enough to throw the gate off its swing plane. The gate then drags at the latch side or binds at the bottom hinge. We reset the post, correct the hinge alignment, and the gate swings like it did when it was first hung.
Yes, and that’s the norm in Sunset. A cracked rail or a busted weld joint is a localized failure, not a reason to replace a perfectly good gate. We cut out the damaged section, weld in matching material, and grind the joint flush. The repair matches Miami-Dade’s NOA wind-load requirements, so it’s not a cosmetic patch. It’s a structural fix.
Most operators made by Viking, Ghost Controls, and DoorKing have a manual release, usually a keyed cylinder or a pull handle on the operator arm or motor housing. Turn the key or pull the release, then push the gate by hand along its normal swing path. Don’t force it if it binds; that’s often a sign the post shifted or the hinge is failing, and forcing it can bend the rail. If the gate won’t move freely after the release, call us at (877) 610-2993 and we’ll come check it.
If the keypad beeps and the operator hums but the gate doesn’t move, the track or the rollers are the likely culprit, especially after a storm pushed debris or the gate frame absorbed a hard gust. A bent track or a seized roller stalls the motor and can burn it out if it keeps trying. We diagnose the track, rollers, and operator together, because replacing the motor without fixing the track just burns out the next one.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Sunset since 2001.