Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Selden
When a gate post rots at the frost line in Selden, the gate doesn’t just sag, it stops latching. That means a Town of Brookhaven pool code violation for a lot of homeowners here, because most Selden yards with in-ground pools were built between the 1960s and 1980s, and those original gates are now 40 to 60 years old. We fix the gate in your driveway, not at some remote shop. On-site welding means the panel stays put, the hinge gets rebuilt in place, and the gate works before the inspector shows up. Call (877) 610-2993 and Hal Gatewood’s crew will get eyes on it fast.
Why Gatewood Fence & Gate Is Selden’s Preferred Gate Parts & Welding Company
Gatewood Fence & Gate has been locally owned and owner-operated since 2001. Hal Gatewood’s name is on the shop and on every invoice. That’s a different kind of accountability than a corporate outfit that changes its estimate at your door. When we quote a price in Selden, that’s the price. Every job carries the 90-Day Done Right Promise in writing, and a live person answers our phone around the clock, not a voicemail and not a call center three states away.
Selden homeowners have a particular problem: aging pool gates and the code requirements that come with them. We’ve welded hundreds of hinge plates, reset dozens of posts along Boyle Road and Middle Country Road, and rebuilt roller assemblies on slide gates off Hawkins Avenue. The person who shows up is background-checked and uniformed, and if the fix doesn’t hold, one call brings us back at no charge. No runaround, no fine print.
We don’t replace what can be repaired. A sagging gate in Selden is usually a post problem or a hinge problem, not a panel problem. Fix the panel without the post and you’ll fix it twice. We’d rather weld a bracket than sell you a whole new gate you don’t need.
Our Gate Parts & Welding Services in Selden
Post Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. Selden’s sandy glacial outwash soil drains fast but heaves with every winter freeze, so posts set 40 years ago lean a little more each spring. When the post is out of plumb, the latch misses the strike and the gate won’t self-close. We cut out the rotted section at the frost line, pour a new concrete footing below the heave zone, and reset the post straight. Most residential post replacements in Selden run $350 to $800 depending on depth and concrete work.
Hinge Replacement
Worn lift-off hinges on old pool gates let the gate drag on the concrete. That bends the rail, stresses the welded corners, and eventually the gate stops swinging at all. We carry heavy-duty adjustable hinges for chain-link, wood privacy, and ornamental steel gates, and we weld reinforcement plates where the old screw holes have wallowed out. If the hinge post itself is sound, hinge replacement in Selden typically runs $180 to $420.
Rail Repair
A bent bottom rail on a 1970s chain-link gate is usually a symptom of a bad hinge, not a cause. We straighten or replace the rail, weld the corner joints where the original factory weld has cracked, and rehang the gate so it swings level. For Selden’s older ranch and split-level properties, rail repair often means working with galvanized pipe that’s rusted thin from decades of freeze-thaw cycles. Rail repairs usually land between $220 and $500.
Custom Welding
Some gates weren’t built to code when they were installed, and some just need a part nobody manufactures anymore. We fabricate latch strikes, hinge brackets, and reinforcement plates in the driveway. On a split-level off Boyle Road, we pulled a 1970s chain-link pool gate where the original hinge post had rotted two feet below grade. The homeowner had already bought a new latch, but the gate still wouldn’t self-close because the post leaned three inches out of plumb. We cut the old post at the frost line, poured a new concrete post footing below the heave zone, rehung the gate on reinforced hinge brackets, and welded a spacer plate onto the latch strike so the Town of Brookhaven compliance check passed that same week. Custom welding jobs in Selden start around $150 and run up from there based on what we’re fabricating.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Selden
We’re certified to service nine major gate brands, and in Selden we work on a lot of legacy Viking and DoorKing equipment installed when these homes were built. Older Elite operators show up on commercial gates along Middle Country Road. We stock common hinge parts, boards, and safety edges for Selden jobs, which means we’re not waiting on a distributor in another state. Whether it’s a Viking operator on a pool gate or a DoorKing slide gate off Hawkins Avenue, our Gate Parts & Welding team can usually get the right part in hand within a day or two.
Common Gate Parts & Welding Problems We See in Selden Homes
- Hinge posts rotted at the frost line: Original 1960s to 1980s gate posts set in Selden’s sandy soil wick moisture every winter. The post rots two feet down, the gate sags, and the self-latching mechanism misses the strike by an inch or more - a direct Town of Brookhaven code violation.
- Worn lift-off hinges dragging gates on concrete: Old pool gates with deteriorated hinges scrape the patio, bending the rail. Left long enough, the welded corner joint snaps and the gate has to be re-welded or replaced.
- Obsolete control boards in legacy operators: Pre-UL 325 openers without safety photocells fail in ways a retrofit can’t always fix. A homeowner’s attempt to mount a new opener on a rusted post usually ends up misaligned, triggering the loop detector every time a car passes.
- Post heave throwing alignment off every spring: The freeze-thaw cycle in Selden shifts shallow-set posts enough that gates pass inspection in September and fail in April. This is the single most common pool gate call we get, and it’s fixable without replacing the entire gate.
Pricing for Gate Parts & Welding in Selden, NY
Here’s what honest pricing looks like in Selden’s market. Hinge replacement runs $180 to $420. Rail repair lands between $220 and $500. Post replacement with new concrete below grade runs $350 to $800. Custom welding starts around $150 for a simple bracket and goes up for larger fabrication. These are real ranges, not bait. The price is quoted and agreed before any work starts, and you get it in writing. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. If another company gave you a written estimate, bring it to us for a free second opinion. Call (877) 610-2993 for an exact quote, estimates are free.
| Repair Type | Typical Selden Price Range |
|---|---|
| Hinge replacement | $180 - $420 |
| Rail repair | $220 - $500 |
| Post replacement with concrete | $350 - $800 |
| Custom welding / fabrication | $150 - $600+ |
We Also Serve Cities Near Selden
If you’re in Centereach, Coram, Farmingville, or Port Jefferson Station, we make the short drive every week. The same Gate Parts & Welding in Selden crew that handles pool gate compliance here covers the surrounding area too, with the same pricing and the same 90-Day Done Right Promise.
Serving Selden, NY - Our Local Coverage Area
We’re based in the Selden area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Selden
Your gate post has heaved. Selden’s sandy glacial outwash soil drains fast but freezes hard in winter, and the freeze-thaw cycle shifts shallow-set posts a little more each season. By April the post is out of plumb enough that the self-latching mechanism misses the strike by an inch or more, which fails Town of Brookhaven pool barrier rules. The fix is resetting the post below the frost line with new concrete, not adjusting the latch. Call (877) 610-2993 and we’ll tell you if the post needs concrete work or just a manufactured hinge realignment.
Hinges first, welding second. A gate sags in the hinge post, not in the middle. If the panel is straight, the problem is almost always worn hinge pins and a post that’s started to lean. We replace the hinges with heavy-duty adjustable ones and add welded reinforcement plates if the old screw holes have wallowed out. Fix the panel without checking the post and you’ll fix it twice. Call (877) 610-2993 for an on-site opinion, and remember the free second opinion applies if you already have a written estimate.
Sometimes, but not always. Pre-UL 325 control boards lack the circuitry to drive modern safety photocells, and mounting a new board on a rusted post creates alignment problems that trip the loop detector. If the operator is Viking, DoorKing, or Elite we may be able to bring it up to Town of Brookhaven standards with retrofit parts. If the board is obsolete and the post is rotted, replacement is cheaper than fighting it. We’ll tell you straight which one applies, and the price is agreed before any work starts. Call (877) 610-2993.
Worth saving means the post is still plumb, the concrete at the base isn’t cracked and lifting, and the steel isn’t rotted through at ground level. We check all three. If the post leans more than half an inch out of plumb or you can see rust crumbling at the soil line, it needs to be cut off and reset with new concrete below the frost line. That’s the only way to pass a Town of Brookhaven pool gate inspection next spring. Call (877) 610-2993 and we’ll give you an honest read in one visit.
A swing gate fails at the hinges and the post; a slide gate fails at the rollers and the track. On Selden’s older properties, swing gates are usually chain-link or wood privacy gates hung on 40-year-old posts, and they sag and miss the latch. Slide gates are more common on wider driveways off Middle Country Road, and they pick up debris in the track, wear the rollers flat, and snap the guide brackets. We diagnose both the same way: find where the wear started, not where it ended up. Call (877) 610-2993 for a free estimate, and we’ll quote you an exact number before any work begins.
Contact Gatewood Fence & Gate for Gate Parts & Welding in Selden
If your gate won’t latch, drags on the ground, or the post is leaning after another Long Island winter, call (877) 610-2993. We answer live, 24/7. We’ll schedule a time, show up in a window we actually keep, and quote you a price you can hold us to. The name is on the shop, the phone is answered by a person, and the work carries a 90-Day Done Right Promise in writing. For Selden pool gates, spring inspection season approaches fast, and a gate that passed in September may fail in April. We’d rather fix the post before the inspector finds it than after.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Selden with on-site gate repair since 2001.