Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Morrow
Gate parts and welding in Morrow usually means one of two jobs: a residential driveway gate that’s sagged on hinges so old they’ve rusted through, or a commercial slide gate off the I-75 South corridor that’s run so many cycles its track anchors have cracked loose from the concrete. We handle both, and we do the welding on site so your gate never leaves your property. Hal Gatewood has been fixing gates since 2001, and our Gate Parts & Welding team serves Morrow with a live person answering every call, day or night. If your gate is binding, dragging, or refuses to close, call (877) 610-2993 and we’ll tell you over the phone what we think is wrong before we ever roll a truck.
Key Takeaways
- Hinge replacement on older Morrow homes typically runs $180-$420 per hinge set, including on-site welding and alignment.
- Post replacement with a new footing poured above the red clay line usually costs $380-$750 per post.
- We answer the phone 24/7 with a live person, not a voicemail.
- Every job carries the 90-Day Done Right Promise in writing.
- We service the commercial slide gates along the I-75 corridor that most residential-only companies won’t touch.
Why Gatewood Fence & Gate Is Morrow’s Preferred Gate Parts & Welding Company
Morrow homeowners and property managers call us because we actually show up and we don’t push replacement when a repair makes more sense. Hal’s name is on every invoice. His address is published. Anyone can look up our license. That matters in a small city like Morrow, where word travels fast and a bad job follows a company for years. We’ve rebuilt gates off Maddox Road, worked the apartment complex entrances near Mount Zion Road, and handled Gate Installation in Morrow for automated slide gates at freight yards along Jonesboro Road. When you call, you get a person who knows Morrow, not a phone tree.
Our 90-Day Done Right Promise is stamped on every work order. If the gate acts up again within 90 days, one call brings us back. No runaround, no fine print. Morrow customers regularly use our free second opinion on written estimates from other companies, and plenty take the $40 off any repair over $200. Seniors and veterans always get 10% off, permanently. And if you’re inside Clayton County, there’s no trip charge.
Our Gate Parts & Welding Services in Morrow
Hinge Replacement
Most of the residential gate failures we see in Morrow’s 1970s-1990s brick ranch neighborhoods are hinge failures. The original ornamental steel gates on these homes have been soaking up Clayton County humidity for decades, and the hinge pins rust-seize until the gate binds every time the operator pushes it. We cut the old hinges off, weld new heavy-barrel hinges in place, and align the gate so it swings clean. On homes in the 30260 and 30287 zip codes, hinge replacement typically runs $180-$420 per hinge set. Fix the hinge before the sag bends your frame, and you avoid a much bigger bill later.
Post Replacement
Morrow’s red clay soil is the quiet killer of gate posts. When spring rains saturate the clay, it swells and shifts the post. When summer drought hits, the clay shrinks and the post settles crooked. Over a few years, that cycle pulls the post out of plumb and the gate starts dragging. We cut the old post at the footing, pour a new footing set above the clay line where it can drain, and weld the gate back to a post that’ll hold. Post replacement in Morrow usually falls between $380 and $750, including concrete, welding, and disposal. A gate sags in the hinge post, not in the middle, and that’s where we start.
Rail Repair
Rail damage on older driveways gates usually traces back to a hinge or post that was failing long before anyone noticed. Once the gate sags, the rail takes strain it was never designed for, and welds start cracking at the corners. We cut out the damaged section, weld in new steel, and reinforce the corners so the rail doesn’t fail again. If the post is still bad, we tell you so. Fix the panel without the post and you’ll fix it twice. Rail repair in Morrow averages $220-$480 depending on how much steel needs replaced.
Custom Welding
When a gate from the 80s has a broken decorative picket or a miter joint splitting open, you can’t just order a new panel. We weld the repair on site, matching the original pattern so the patch doesn’t look like a patch. We also build custom steel reinforcement braces for gates that were never designed for an operator, which is common on older Morrow homes where owners added automation to a gate built in 1985. Custom welding work in Morrow runs $150-$600 based on the scope, and we quote the number before any torch lights up.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Morrow
Our team is factory-certified to work on nine major gate brands, and for Morrow properties we most often service Morrow Gate Motor & Opener units from FAAC, BFT, Linear, and Viking on both residential and commercial sites. We keep common FAAC and BFT control boards, Linear receiver boards, and Viking motor capacitors in the truck for faster turnaround. If a board is obsolete, we’ll tell you straight and show you retrofit options that keep your existing gate and poles. No stocking fee, no upsell.
Common Gate Parts & Welding Problems We See in Morrow Homes
- Rust-seized hinge pins on original ornamental steel gates. Decades of Clayton County humidity weld the pin to the barrel, and the gate eventually stops swinging. The fix is cutting the old hinge off and welding on a new set.
- Heaved or cracked slide gate track anchors in the industrial parks off I-75 South. Red clay swells under the concrete pads, and passing truck vibration shakes the anchors loose. We re-anchor the track and weld reinforcement plates to keep it from walking.
- Obsolete single-button operators on 1970s-era residential gates. These old boards don’t meet modern entrapment standards and often can’t be repaired because parts were discontinued before most Morrow homes changed owners twice. We retrofit them with safety photocells and current operator logic.
- Latch and lock failures caused by post shift. The gate swings true mechanically, but the latch won’t catch because the post has drifted a few degrees out of plumb. Repairing just the latch buys you six months. Replacing or resetting the post fixes it.
Pricing for Gate Parts & Welding in Morrow, GA
Here’s what you can expect to pay in Morrow, based on work we’ve done in the area:
- Hinge replacement: $180-$420 per hinge set, including welding and alignment
- Post replacement (residential, standard 4″-6″ steel post): $380-$750 per post, including concrete, welding, and cleanup
- Rail repair: $220-$480 depending on length and whether we’re adding reinforcement
- Custom welding (pickets, corner cracks, bracing): $150-$600 based on scope
- Commercial slide gate track re-anchoring: $600-$1,400 depending on track length and how many anchors need rebuilt
The quote you get on the phone is the price you pay when we leave, unless we uncover something structural we couldn’t see. If that happens, we stop, show you, and get written approval before any extra work starts. No trip charge inside Clayton County, and every estimate is free. Call (877) 610-2993 for an exact number on your gate.
We Also Serve Cities Near Morrow
Beyond Morrow, our Gate Parts & Welding crew regularly handles jobs in Forest Park, Irondale, Riverdale, and Conley. Same local pricing, same 90-Day Done Right Promise, and the same live person on the phone whenever you call.
Serving Morrow, GA - Our Local Coverage Area
We’re based in the Morrow area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Morrow
The tracks crack because Morrow’s red clay soil expands and contracts with rain and drought, while the constant vibration from heavy trucks on the I-75 South corridor loosens the concrete pads anchoring the track. We fix this by re-anchoring the track, welding reinforcement plates over the cracked sections, and setting new anchors deeper than the clay line. Call (877) 610-2993 if your dock gate is dragging off its track.
Yes, in most cases we can keep your existing gate and poles and add Gate Access Control - Morrow features like a current operator with photocell safety edges and auto-reverse logic. The older the gate, the more likely it needs hinge and leveling work first. We’ll check the hinges, post plumb, and gate balance before we recommend the retrofit, because putting a new operator on a binding gate burns out the motor. Call for a free site check.
Sag usually starts at the hinge post, not the panel. Rusted hinge pins and a post that’s shifted in the red clay let the gate drop, and welding in a sag correction plate helps only if the post and hinges are sound. If the post is rotted at the footing, a panel repair buys you a year at best. That’s why we start every sag repair by checking post plumb and hinge wear. We rebuilt exactly this kind of gate on a 1980s brick ranch off Maddox Road, where the hinge post had rotted at the footing and the gate needed a new post, new hinges, and a sag plate to swing clean.
Red clay swells when wet and shrinks when dry, so a post footing poured at ground level will shift over time in Morrow. We set new footings above the clay line with drainage gravel beneath them, which keeps the post stable through wet springs and dry summers. A standard residential post replacement in Morrow runs $380-$750, and we’d rather do it right once than come back in two years.
We’re certified to service FAAC, BFT, Linear, Viking, LiftMaster, DoorKing, Elite, Ghost Controls, and Mighty Mule. For the distribution centers and freight yards along the I-75 corridor, we most often repair FAAC and BFT slide operators, Linear receiver boards, and Viking motor capacitors. If your operator runs hundreds of cycles a day and it’s taking longer to close, call (877) 610-2993 and we’ll diagnose it before it locks out your trucks.
Call Gatewood Fence & Gate for Gate Parts & Welding in Morrow
A gate that won’t close isn’t an inconvenience. It’s a hole in your fence, a liability for your property, and a repair that only gets more expensive the longer it waits. We weld on site, we quote before we work, and we answer the phone around the clock. Hal Gatewood’s name is on the shop and on every invoice. If you’re in Morrow, call (877) 610-2993 for a free estimate on hinge replacement, post replacement, rail repair, custom welding, or a commercial slide gate that’s been eating track anchors. We’ll tell you what’s wrong, what it costs, and when we can be there.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Morrow with gate parts and welding since 2001.