Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Morrow
Gate installation in Morrow, GA typically runs $1,200 to $6,800 depending on whether you’re hanging a residential driveway gate or a commercial slide gate on the I-75 South corridor. We’re Gatewood Fence & Gate, and we’ve been installing and repairing gates since 2001. Hal Gatewood owns the company, his name is on the shop, and the person who answers when you call (877) 610-2993 is a live human being, not a phone tree. If you live off Maddox Road, over by Clayton State, or in one of the brick-veneer ranch neighborhoods near Morrow Lake, we know what your gate posts are sitting in. That matters more than most people realize.
Why Gatewood Fence & Gate Is Morrow’s Preferred Gate Installation Company
Morrow has a gate problem most suburbs don’t. This city sits squarely on the I-75 South commercial corridor in Clayton County, which means automated slide gates at distribution centers and freight yards run through hundreds of open-close cycles a day. That’s a completely different wear pattern than a residential gate in neighboring Forest Park that cycles maybe six times daily. We learned this the hard way years ago, before we started working out of our Atlanta shop and sending crews into Morrow regularly. The concrete pads anchoring commercial slide gate tracks here crack and heave because the red clay underneath swells when it rains and shrinks when it doesn’t, and the constant vibration from loading dock truck traffic doesn’t help.
For Morrow homeowners, the pattern is different but just as predictable. The residential stock in the 30260 and 30287 zip codes is mostly 1970s through 1990s brick-veneer ranches with original ornamental steel gates. Clayton County humidity has been rusting those hinge posts for decades. We show up and find the gate sagging, the post seized, and an operator arm that snapped because it was fighting a bind nobody fixed at the source. We’re the Gate Installation company that pulls the post, sets a new footing, and welds on site, so the gate never leaves your driveway. Our Morrow customers get the 90-Day Done Right Promise in writing on every job. If it’s not right, Hal comes back himself. One call does it.
Our Gate Installation Services in Morrow
Driveway Gate Installation
Driveway gate installation in Morrow runs $2,400 to $6,800 for a typical residential swing or slide setup, including operator, safety edges, and post footings. In the 1970s-era neighborhoods off Maddox Road and around Morrow Lake, we’re usually replacing a rusted ornamental steel gate or retrofitting an old single-button operator with a modern UL 325-compliant system. We quote the price before any work starts. You sign off on it, we do the work, and the invoice matches the quote.
Pedestrian Gate Installation
Pedestrian gates in Morrow apartment complexes and older homes typically run $800 to $2,200 installed. These are usually lightweight steel or aluminum gates with code-compliant latches and closers. We see a lot of these paired with driveway gates, especially on corner lots where foot traffic cuts through from the street side. If the gate is for a pool enclosure or any regulated access point, we install to code with self-closing hinges and proper latch height.
Sliding Gate Installation
Sliding gate installation in Morrow’s industrial parks off I-75 South is the heaviest work we do here. These gates run 20 to 40 feet, cycle constantly, and sit on track systems that Clayton County’s red clay wants to move. A new commercial slide gate with operator and reinforced track anchors runs $4,500 to $15,000 depending on duty cycle and panel weight. We over-engineer the track footings because we’ve pulled enough cracked anchors out of this corridor to know what’s coming. For residential slide gates, expect $2,800 to $5,500. We weld on site, which means your gate never gets hauled to a shop.
Swing Gate Installation
Swing gate installation in Morrow usually costs $1,800 to $5,500 for a residential double or single swing setup. The hinge post is where everything lives and dies. In Morrow’s clay, a post set shallow will shift within two or three seasons. That’s why we dig footings below the frost line, set the post in concrete, and wait for it to cure before hanging the gate. A gate sags in the hinge post, not in the middle, and that is where we start. Security gate installation, especially for the older apartment complexes and storage yards around the 30260 corridor, is another piece of this. Those jobs often include keypad entry or access control boards, and we service or install all of it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Morrow
We’re certified to service and install nine major gate operator brands, and for Morrow’s mix of residential and industrial work, we lean on the ones that hold up. FAAC and BFT make operators that handle high-duty-cycle commercial slide gates, which is exactly what the I-75 South distribution centers need. Linear makes residential swing and slide operators that are common on Morrow’s older ranch homes, and Viking builds access control components we pair with security gates. We keep common parts stocked for these brands, which means when a Morrow gate goes down on a Tuesday, we’re not waiting a week on a shipment to get it running. Certified to work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Common Gate Installation Problems We See in Morrow Homes
- Rust-seized hinge posts on 1970s-1990s ornamental steel gates. Clayton County humidity gets inside the hinge barrel, rust welds it, and the gate starts dragging. We cut out the old hardware, set fresh hinges, and re-hang the gate with sag correction rather than replacing the whole panel.
- Outdated single-button operators that lack entrapment protection. We regularly pull operators off Morrow homes that predate UL 325 photo eye and edge sensor requirements. Those are safety hazards, and retrofitting them with modern photocells is cheaper than waiting for the gate to close on a car or a person.
- Shifted posts from expansive red clay. Morrow’s soil swells in spring rains and shrinks in summer drought. Posts set too shallow drift out of plumb, and the gate binds. We fix this with deeper footings and sometimes helical piers on the worst lots.
- Cracked slide gate track anchors on the I-75 South corridor. Heavy truck vibration plus clay movement loosens the concrete pads that hold commercial track systems. We regularly find the track floating and the rollers burning out against it. The fix is re-anchoring the pad with deeper steel reinforcement, not just tightening bolts.
Pricing for Gate Installation in Morrow, GA
Residential gate installation in Morrow runs $1,200 to $6,800. Pedestrian gates start around $800. A standard single swing driveway gate with a Linear operator and safety photocells lands between $2,400 and $4,200. Double swing gates run $3,500 to $5,500. A commercial slide gate on the I-75 South industrial corridor starts around $4,500 and can exceed $15,000 for heavy-duty, high-cycle systems with access control. What affects the price: gate width and weight, whether the existing posts can be saved, operator duty cycle, and whether we need to run power to the gate. We give you a written quote before any work starts, and the price doesn’t change at the door. Estimates are free. Call (877) 610-2993 and we’ll come measure. No trip charge inside Clayton County.
We Also Serve Cities Near Morrow
We work throughout Clayton County and the surrounding area. If you’re in Forest Park, Irondale, Riverdale, or Conley, you’re inside our service territory, and we know the roads well enough to give you an honest arrival window. The same crew that handles Gate Installation in Morrow covers these nearby cities, with the same written promise and the same live person on the phone. No call center, no runaround.
Serving Morrow, GA - Our Local Coverage Area
We’re based in the Morrow area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Morrow
The clay underneath the concrete pad expands and contracts with rainfall, and the vibration from heavy trucks at adjacent loading docks works the anchor bolts loose over time. We fix it by cutting out the cracked pad, drilling deeper steel reinforcement into stable soil, and re-pouring with rebar tied into the new track anchors. If your gate is drifting or the track is bouncing, call (877) 610-2993 before the rollers burn out and the repair gets more expensive.
Yes, in most cases. If the operator itself is still functional and the gate frame is sound, we can add UL 325-compliant photocells and safety edges without replacing the whole system. The real question is whether the hinge posts are rust-compromised. If they are, retrofitting the operator without fixing the posts means you’ll be back in the same spot in a year. We’ll tell you honestly which path is cheaper over five years.
The clay swells when it’s saturated and shrinks when it dries, which puts lateral pressure on post footings. We dig below the active soil zone, use concrete with proper drainage gravel at the base, and let the footing cure fully before hanging the gate. On lots where the clay is especially expansive, we recommend helical piers. This is not a corner you cut in Morrow, and it’s why we don’t set posts shallow to save time.
If the operator is a single-button model that predates UL 325 entrapment standards, replacement is almost always cheaper than patching it. The boards are obsolete, parts are scarce, and the safety upgrade alone justifies the cost. When the motor, board, and limits all need replacing, you’re within $200 to $400 of a brand-new operator with a warranty. We’ll show you the numbers side by side and let you decide. Estimates are free at (877) 610-2993.
Rust-seized hinge posts. The ornamental steel gates on 1970s to 1990s brick-veneer ranches have been sitting in Clayton County humidity for decades, and the hinge barrels corrode from the inside. The gate starts dragging, the operator arm strains, and eventually something snaps. We replace the hinges, correct the sag, and set the posts properly if they’ve shifted. Fixing the panel without the post and you’ll fix it twice.
If you’re in Morrow and your gate is sagging, stuck, or simply old enough that you’re not sure it’s safe, call (877) 610-2993. We’ll come out, look at what you have, and give you a straight answer. We do free estimates, we stand behind our work with the 90-Day Done Right Promise, and seniors and veterans always get 10% off. Hal Gatewood’s name is on the shop and on every invoice. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Morrow and Clayton County since 2001.