Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Manhattan Beach
Gate parts and welding in Manhattan Beach usually means one of two calls: a hinge that seized from salt air, or a weld that cracked on a custom steel frame. On most jobs we’re there the same day or next morning, and the price is set before we start. Hal Gatewood has been repairing gates since 2001, and the crew that shows up in Manhattan Beach knows the difference between a hinge you can save and one the ocean already ruined. Call (877) 610-2993 and you’ll get a live person, not a recording.
Why Gatewood Fence & Gate Is Manhattan Beach’s Preferred Gate Parts & Welding Company
We’re not a national outfit running crews through six counties. We’re locally owned, Hal’s name is on the shop and on every invoice, and our Gate Parts & Welding team works the South Bay every week. Manhattan Beach homeowners tend to ask the same three things: will someone actually show up, will the person know what they’re looking at, and will the price match the quote. Yes, yes, and yes.
Reviews from Manhattan Beach customers regularly mention the same thing: Hal or one of his crew showed up in the window promised, looked at the gate, and told them straight what needed fixing and what didn’t. No upsell on a post that was fine. No “you need a whole new gate” when a weld and a hinge plate would do. That’s the repair-first approach we’ve run on since 2001.
Response time to Manhattan Beach is usually same day for a seized hinge or a gate stuck open. A cracked weld on a steel frame might be next morning depending on the day, but you’ll know when we’re coming before we hang up. Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No runaround.
Our Gate Parts & Welding Services in Manhattan Beach
Hinge Replacement
Salt air off the Pacific eats hinge pins and plates faster than anything inland. In the Sand Section, we regularly replace hinges on gates that are only two or three years old because the original installer used hardware that was never meant for marine conditions. We cut out the old hinge, weld in a marine-grade replacement, and coat it so it actually holds up.
Post Replacement
A sagging gate in Manhattan Beach is almost never a gate problem. It’s the post. In the Hill Section, where a lot of homes sit on slopes with older footings, posts lean and pull out of the concrete over time. We dig out the footing, set a new post in proper concrete, weld the hinge plates back on, and the gate swings true again. Done right, not patched.
Rail Repair
Slide gates with bent or corroded rails are common in Manhattan Beach, especially on 30-foot lots where the gate has to run tight against a wall or a property line. We straighten or replace the rail, repair the rack, and get the rollers moving smooth. If the rail is too far gone, we’ll tell you that instead of wasting your money trying to save it.
Custom Welding
We weld on site. The gate stays in your driveway. We’re not hauling a 200-pound steel gate back to a shop and leaving your property open for two days. For ornamental iron gates in Manhattan Beach, we can weld in replacement pickets, repair cracked scrollwork, rebuild a snapped hinge mount, or fabricate a small section that matches the existing design. The welds get treated for salt exposure so they don’t rust through in three years.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Manhattan Beach
We service Viking, Ghost Controls, and DoorKing operators regularly, along with Elite and several other major brands. For Manhattan Beach customers, we keep common parts on the truck: hinge plates, roller assemblies, rack sections, and striker plates. That means fewer trips back and forth across the 405, and a gate that’s working again the same day instead of later in the week.
Common Gate Parts & Welding Problems We See in Manhattan Beach Homes
- Seized hinges from salt air: Original hardware on Sand Section gates seizes within two or three years. Lubrication won’t fix it. The hinge gets cut out and replaced with marine-grade steel, then the post gets checked for corrosion behind the plate.
- Hairline cracks at weld seams: Custom steel frames within a few blocks of the strand show stress cracks at welds inside 4-6 years. Salt spray gets into the micro-gaps and accelerates the failure. We grind out the crack, reweld, and treat the area.
- Sagging gate blocking a shared driveway: Tight lot footprints mean a sagging gate can block a neighbor’s only access. Post replacement has to happen without keeping the gate offline for more than a shift. We plan the job that way from the first look.
- Corroded motor housings on slide gates: The marine layer doesn’t just affect the gate. Operators near the water corrode quickly, especially LiftMaster and Viking units mounted close to the ground. Sealed housings and marine-grade fasteners make a real difference on the replacement.
Pricing for Gate Parts & Welding in Manhattan Beach, CA
Hinge replacement in Manhattan Beach typically runs $185-$380 per hinge, depending on whether it’s a welded plate or a bolt-on unit and how bad the surrounding steel is. Post replacement runs $450-$900 for a standard ornamental iron post with concrete footing in the Sand Section or Hill Section; tight access can push that toward the top of the range. Custom welding work is quoted by the job: a cracked frame repair usually runs $250-$550, while rebuilding a hinge mount or fabricating a small section might be $400-$800. Rail repair on a slide gate sits between $300 and $650. Every price is quoted and agreed before any work starts, and we don’t change the number at the door. There’s no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote – estimates are free.
We Also Serve Cities Near Manhattan Beach
Our crews work up and down the coast and into the South Bay. If you’re just north or east of Gate Parts & Welding in Manhattan Beach, we regularly run jobs in Redondo Beach, Rolling Hills Estates, Palos Verdes Estates, and Torrance. Same live answer on the phone, same 90-Day Done Right Promise.
Serving Manhattan Beach, CA - Our Local Coverage Area
We’re based in the Manhattan Beach area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Manhattan Beach
Because the original installer used non-marine-grade hardware and the salt air off the Pacific destroys it. Hinges on gates within a few blocks of the strand in the Sand Section seize up or corrode through in two to three years, especially if they’re galvanized steel instead of true marine-grade stainless or coated steel. We replace them with hardware meant for coastal conditions, and we check the plate and the post behind the hinge before welding anything back on. Call (877) 610-2993 and we’ll tell you if your hinge can be saved or if it’s already too far gone.
Almost always yes. We weld on site in Manhattan Beach, so the gate stays on its hinges in the driveway while we grind out the crack, reweld the seam, and treat the area for salt exposure. Removing the gate is only necessary if the frame is twisted or the crack runs through a structural mount point, and even then we brace it in place during the work so your property isn’t left open overnight.
Sealed bearing rollers with stainless or coated hardware. Standard rollers with open bearings get packed with salt and sand within a year or two near the water, and then the gate starts binding and hanging up. We replace rollers, check the rail for salt crust and pitting, and adjust the rack so the gate runs smooth instead of grinding. The job usually takes under two hours.
Nine times out of ten it’s the post, not the gate. A gate sags in the hinge post, not in the middle, and that’s where we start. If the post is cracked, leaning, or the footing has shifted on a sloped Hill Section lot, we set a new post in fresh concrete, weld the hinge plates back on, and the gate hangs right. You only need a new gate if the frame itself is twisted or the hinge mounts have torn out past the point where welding makes sense. We’ll show you exactly what we’re seeing before we touch anything.
Yes, if it’s set up as a compact slide configuration and the rail and rollers are matched to the available width. We’ve done this repeatedly in the Sand Section off narrow rights-of-way where a swing gate simply won’t fit. The keys are low-profile track, proper post anchoring, and a motor sized for the gate weight, not the lot width. If you’re not sure what fits, call (877) 610-2993 and we’ll measure and give you a written price before any work starts.
What Manhattan Beach’s Salt Air Does to Gate Hardware
Manhattan Beach sits directly on the Pacific, and the marine layer doesn’t just fog the windows. It carries salt-laden air that attacks ferrous metal year round. Hinges, pivot pins, weld seams, striker plates, and motor enclosures all corrode faster here than they do a few miles inland in Torrance or Gardena. We see gate operators and springs that might last 10-12 years in Hawthorne showing serious degradation in 4-6 years in the Sand Section, just blocks from the waterline.
This is the part that surprises people who move here from somewhere the air doesn’t eat steel. A wrought-iron gate on a $4 million Manhattan Beach rebuild can look brand new from the street while the hinge pins inside are rusting to dust. The housing stock here doesn’t help: high-value custom and semi-custom homes, many of them teardown-rebuilds from the last two decades, with automated driveway gates, ornamental iron pedestrian entries, and tight lot footprints that push swing arcs and slide configurations right to the edge. Locals call it the “beach tax” on gate calls: the original installer used inland hardware, and now the gate needs work two or three years later.
We replaced the hinge post and welded a new rack and pinion on a sliding gate in the Sand Section off a narrow right-of-way where a swing gate simply wouldn’t fit. The original operator was a LiftMaster that had corroded so badly the motor housing was seizing, and the track rollers were binding on salt-crusted rails. After cutting out the old post footing and welding in marine-grade steel, the gate now cycles quietly even with the marine layer rolling in nightly. That’s the difference between hardware that survives Manhattan Beach and hardware that doesn’t.
Call Gatewood Fence & Gate for Gate Parts & Welding in Manhattan Beach
If your gate is sagging, seized, cracked, or just making a sound it didn’t make last week, call (877) 610-2993. You’ll get a live person who can talk you through what you’re seeing and give you a straight idea of what it’ll take. Estimates are free, the price is set before we start, and every job carries the 90-Day Done Right Promise in writing. Serving Manhattan Beach zip codes 90266 and 90267, from the Sand Section up through the Hill Section.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Manhattan Beach since 2001.