Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lynn
If you’re searching for gate parts and welding in Lynn, MA, you’re probably looking at a hinge that’s seized solid from harbor air, or a post that’s heaved out of plumb over three decades of New England winters. We’re Gatewood Fence & Gate, and we fix those exact problems every week across Lynn’s triple-decker blocks and waterfront streets. Hal Gatewood has run this shop since 2001, and when you call (877) 610-2993, a live person answers. Not a recording, not a queue. On-site welding means your gate stays in your driveway while we work on it, and every job carries our 90-Day Done Right Promise in writing.
Why Gatewood Fence & Gate Is Lynn’s Preferred Gate Parts & Welding Company
Lynn gates fail differently than gates in Peabody or Saugus. Salt air off Lynn Harbor eats at exposed steel year-round, and frost heave pushes old concrete footings around every winter. We’ve been correcting those two forces since long before the national outfits started selling gate services door-to-door. Hal Gatewood personally walks every Lynn job before quoting, and his published address and license number are easy to verify. The name is on the shop, and the shop is down the road; that’s the oldest accountability there is.
Our Lynn customers keep our schedule full, and their reviews tell you what to expect. We answer live around the clock, and for repair work inside Lynn we can typically get a crew to your street the same day you call. When we show up in your driveway off Lynn Shore Drive or on a side street near Flax Pond, it’s Hal or one of his background-checked crew members, in uniform, with the parts the job needs loaded in the truck. We’ve serviced gates within a mile of Lynn Common, down along the harbor in the 01902 zip, and up the hill toward Wyoma Square in 01905. The same team, the same promise, every time.
Our Gate Parts & Welding Services in Lynn
We carry the parts that actually survive on the Lynn coast, and we weld on site rather than hauling your gate off to some shop. Here’s how that applies to the most common repairs we handle in this city.
Hinge Replacement in Lynn
Most swing gates in Lynn hang on original cast iron hinges that have been soaking in salt air since the first Bush administration. Once those hinges seize, the gate gets forced open and closed until the hinge itself cracks or tears from the frame. We stock galvanized and stainless hinge sets sized for older ornamental iron gates, and we can weld replacement hinge sleeves directly onto the existing panel when the original mounting points have rotted away. A typical hinge replacement in Lynn runs $180 to $340 per pair, installed, depending on the weight of the gate and whether we’re replacing just the hinge or also repairing the frame behind it.
Post Replacement in Lynn
A sagging gate in Lynn is rarely just a sagging gate. The hinge post has usually moved, because the concrete footing poured around it 60 or 70 years ago has cracked from decades of salt-saturated freeze-thaw cycling. We dig out the old footing, set a galvanized steel schedule 40 post deeper than the original, add gravel drainage so water can’t pool at the base, and pour a new footing that won’t heave the first winter. Most post replacements in Lynn run $450 to $900 depending on depth, access, and whether we need to match an existing fence line. We price the job before any work starts, and that price is the price.
Rail Repair in Lynn
Chain-link gates on older Lynn triple-deckers fail at the pipe joints long before the chain-link fabric itself gives out. The bottom rail takes the most abuse: standing water, road salt tracked in from the street, and harbor air working on galvanized pipe that was never meant to last 50 years. We cut out the corroded section, weld in new pipe, and brace the frame so the gate hangs straight again. When the rail is too far gone, we reframe the entire gate around the existing fabric where the fabric is still sound. Expect $200 to $450 for a typical rail repair, less when it’s caught early.
Custom Welding in Lynn
Lynn’s housing stock predates standard gate widths by a few decades. Rear-yard gates on early-1900s triple-deckers on narrow lots often sit in openings that were built for horse-cart access or coal delivery, and no off-the-shelf panel fits cleanly. We take measurements on site, fabricate the frame in our shop, and weld the final assembly in your driveway. Custom gate fabrication in Lynn runs $600 to $1,800 depending on size, material gauge, and whether you want ornamental scrollwork to match an existing Victorian-era fence. We’ll give you a written price before we touch a piece of steel.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lynn
We’re certified to service the opener and operator brands you already have on your gate: LiftMaster and FAAC on most residential swing systems, plus BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule where Lynn homes have been retrofitted. If you’ve got a Ghost Controls slide operator that’s been fighting rust on the rack, or a Viking swing arm that’s dragging a post-less hinge, we can diagnose it. We keep common boards, limit switches, and safety edge components for these brands in our service trucks, so a repair in Lynn doesn’t mean waiting a week for a part to show up from a warehouse in Ohio.
Common Gate Parts & Welding Problems We See in Lynn Homes
- Hinge posts heaved out of plumb: Salt-saturated soil near Lynn Harbor expands harder during freeze-thaw cycles than dry inland soil. A post that looked straight in October can be 2-3 inches out of line by March, dragging the gate across the driveway threshold and popping the latch.
- Cast iron hardware seized solid: We regularly remove hinges and latches on L Street and Eastern Avenue homes where the original hardware hasn’t moved in a decade. Once salt air works past the paint and into the pin tolerances, the metal fuses. The fix is cutting out the old hinge and welding in new stainless, not drilling and hoping.
- Rusted chain-link rails snapping at the joints: Original rear-yard gates on Lynn triple-deckers were built with thin-gauge galvanized pipe. After 40-50 years of harbor air and standing moisture at the bottom joint, the pipe fails from the inside out. One good shove and the rail gives.
- Gate operators struggling against moving posts: A LiftMaster or Ghost Controls operator can’t fix a hinge post that’s drifting. When a Lynn gate stops closing or reverses mid-cycle, the first thing we check is whether the post is still plumb. Half the time, the operator is fine and the concrete underneath isn’t.
Pricing for Gate Parts & Welding in Lynn, MA
Here’s a straight answer on cost, because you deserve one before you make the call. Hinge replacements run $180 to $340 per pair. Post replacement with a new galvanized steel post and deeper footing runs $450 to $900. Rail repair on a chain-link gate runs $200 to $450. Full custom fabrication of a new gate frame runs $600 to $1,800. What moves the number within those ranges: access to the post, depth of the existing footing, weight of the gate, and whether we’re working with ornamental iron or basic chain-link. Every price is quoted and agreed to in writing before any work starts. We don’t change the number at the door. Right now: $40 off any repair over $200, no trip charge inside Lynn, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and Hal will come out to look at the gate in person.
We Also Serve Cities Near Lynn
Our Gate Parts & Welding crews work up and down the North Shore every week. You’ll see our trucks in South Peabody, Swampscott, Saugus, and Revere as well as here in Lynn. If you’re a few minutes outside the city line, call anyway; chances are we’re already scheduled on your street later this week.
Serving Lynn, MA - Our Local Coverage Area
We’re based in the Lynn area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lynn
Lynn’s hinge posts fail faster because salt-saturated soil from harbor air accelerates freeze-thaw expansion near the surface. Water, salt, and repeated freezing loosen the top few inches of concrete footing, and each winter cycle heaves the post a little further out of plumb. Peabody and Saugus sit inland enough that their soil doesn’t carry the same salt load, so their footings stay tighter longer. Fix is the same either way: deeper footing, gravel drainage, and a galvanized post. If your gate in Lynn is dragging, call (877) 610-2993 for a free site look.
In most 01901 homes along the waterfront blocks, we can weld a new hinge sleeve directly onto the existing panel even when the original hinge has rotted away. The key is checking the frame’s remaining wall thickness first. If the steel still has structural integrity behind the rust, we grind it back to bare metal and weld in fresh stainless. If the frame’s been rusted thin in the hinge zone, we’ll tell you before we start. Crews run through the 01901 zip weekly, and we’re usually there the day you call for repair work.
Use galvanized steel on a replacement gate frame anywhere within a mile of Lynn Beach. Galvanized steel’s zinc coating sacrifices itself to the salt air before the underlying steel can corrode, and a properly hot-dipped galvanized frame near the shoreline will outlast painted steel by a decade or more. The paint fails first at the corners and weld seams, and once moisture gets trapped under the paint, the tube rusts from the inside out. We specify hot-dipped galvanized on every salt-exposed gate we build in Lynn. The upfront cost is maybe 20% more, and it lasts about twice as long.
The gate’s moving hardware fails before the operator does, and the rack usually goes first. On a slide gate with a Ghost Controls or LiftMaster operator near the water, the rack teeth and the V-track pick up salt and freeze in winter, and the drive gear chews through the coating on the rack within a few seasons. Once bare steel is exposed at the gear contact points, the operator works harder to move the gate, the safety edges trigger more often, and eventually the rack fails. We replace racks and tracks multiple times per year in the high-density rental corridors near Lynn’s waterfront.
We dig out the old footing by hand when we have to, because most Lynn triple-decker side yards won’t fit a mini-excavator. The 1950s concrete usually breaks apart with a sledge and a digging bar, and then we go deeper than the original, add a gravel drainage layer at the bottom, set a galvanized schedule 40 post, and pour a new footing with rebar. On narrow lots where the old gate post sits tight to a foundation wall, we’ll often shift the post six inches if it gets better soil. That’s a normal Lynn gate job for us; we’ve done hundreds like it. Call (877) 610-2993 and Hal will come measure it himself.
Get Your Lynn Gate Fixed Right - Call Now
If you’ve got a gate in Lynn that’s dragging, sagging, rusted shut, or fighting its operator, call us. Hal will come out, look it over, and hand you a written price before any work starts. Salt air and frost heave aren’t going to give your gate a pass next winter. The earlier we catch a failing post or a seized hinge, the less you pay. Call (877) 610-2993 for a free estimate, and if another company already quoted you, bring us their written estimate. We’ll give you a free second opinion on it. Hal Gatewood’s name is on the shop, and he’ll be the one standing in your driveway.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate.