Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lyndon
If your Lyndon driveway gate sags, binds, or won’t open after the last freeze, you need a welding repair that actually holds. Gatewood Fence & Gate has been fixing ornamental iron gates and automatic openers since 2001, and we do the welding right in your driveway so the gate never leaves your property. A live person answers our phone 24/7 at (877) 610-2993, and every job carries our 90-Day Done Right Promise in writing. We know Lyndon’s older gates because we’ve repaired hundreds of them across the 40222 ZIP.
Why Gatewood Fence & Gate Is Lyndon’s Preferred Gate Parts & Welding Company
Hal Gatewood’s name is on the shop, the invoice, and every weld we make in Lyndon. That’s the oldest accountability there is. We’ve been locally owned and owner-operated since 2001, and our crew works the eastern Jefferson County suburbs every week, so we’re not learning your neighborhood from a GPS on the day of the call. When a Lyndon homeowner off La Grange Road or near Westport Road needs a hinge post cut out and reset, the person who shows up knows what clay soil does to a footing and how to set the new post so it stays put.
We repair first and replace only when replacement is the honest cheaper answer. That’s not a slogan; it’s how we bid every job. If another company quoted a whole new gate and we can fix the rail and hinges for a third of the cost, we’ll tell you. The 90-Day Done Right Promise means if something isn’t right, one phone call brings Hal back. No runaround, no fine print.
Lyndon customers call us for a few simple reasons: a live person picks up around the clock, the price quoted is the price on the invoice, and we don’t swap parts that don’t need swapping. We’re certified to service DoorKing, Viking, Linear, and Ghost Controls operators, which matters when a legacy control board from the 1990s finally gives out after one freeze-thaw cycle too many.
Our Gate Parts & Welding Services in Lyndon
Here’s what we actually do on gates across Lyndon. These four services cover most of what goes wrong with iron driveway gates in the 40222 ZIP.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. On Lyndon’s older wrought iron gates, the hinges are usually the original equipment from when the house was built, and decades of ice weight and freeze-thaw cycling have wallowed out the pin holes and cracked the weld at the post. We cut off the old hinge, grind the post clean, and weld on a new barrel hinge or strap hinge sized to carry the gate’s actual weight, then re-hang the panel so it swings level without dragging.
Post Replacement
Jefferson County clay heaves every winter, and Lyndon’s original gate posts from the 1950s through the 1980s were often set in shallow footings that were undersized even for their day. When a post leans or shifts, the gate binds against the latch post and the opener motor fights the load until something fails. We cut out the old post and footing, dig deeper, set the new post in concrete, and weld a fresh hinge plate. If the rail is still sound, the gate stays.
Rail Repair
Freezing rain in Lyndon drops ice onto ornamental iron panels and bends the top rail, especially where mature hardwoods hang over long private driveways. A bent top rail throws the whole gate out of square, so the pickets twist and the latch stops lining up. We straighten the rail cold when we can, weld in a reinforced section when we can’t, and occasionally add a diagonal brace if the panel has been racking for years. The fix is invisible, and the gate hangs straight again.
Custom Welding
Some repairs aren’t a replacement part; they’re a weld that has to be made on site, matched to the original iron. We weld cracked rails, broken scrollwork, snapped hinge plates, and torn operator brackets. Our truck carries a welder and the right stock to match most Lyndon-era gate profiles, so the patch doesn’t look like a patch. When the original section is too far gone, we fabricate the replacement piece in place rather than hauling the gate to a shop across town.
Beyond these four, we also handle gate rollers, latches and locks, and full automation retrofits for older gates. For the full service list, see our Gate Parts & Welding page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lyndon
Lyndon’s older automatic gates often run on operators that haven’t been made in years: DoorKing boards, early Viking swing arms, Linear control panels, Ghost Controls sets from the mid-2000s. We’re certified on nine major gate brands, and because we stock common parts locally rather than ordering everything from a distributor, a failed control board on a Lyndon gate can often be replaced same-visit. If the board is obsolete and no longer manufactured, we’ll tell you straight and show you the retrofit options, including adding modern UL 325 entrapment protection that the original system never had.
Common Gate Parts & Welding Problems We See in Lyndon Homes
Every week brings the same calls from across Lyndon. If any of these sound like your gate, call us before the next freeze makes it worse.
- Top rail bent by ice weight. Freezing rain loads ornamental iron panels with ice, and the top rail bends before the hinges give. On a 1950s Lyndon gate with old hardware, one ice storm can leave the panel twisted and the latch a half-inch out. We straighten or reinforce the rail and re-align the hinges in a single visit.
- Hinge post leaning from clay soil. Expansive clay under Lyndon heaves every winter. A post that looked plumb in August can lean a full inch by March, binding the gate against the latch post and stalling the opener motor. The fix is cutting out the old footing and setting a new post deeper in concrete, not shimming the hinges.
- Obsolete control board dead after freeze-thaw cycles. Legacy operators from DoorKing, Viking, and Linear fail most often after repeated cold snaps, when the board’s capacitors and relays have seen too many expansion cycles. We carry replacements and retrofits, including modern entrapment protection for older systems.
- Worn hinge barrels and cracked welds. Decades of opening and closing work-harden the steel until the hinge pin holes egg out and the weld at the post cracks. You’ll hear it before you see it: a groan or a click at the hinge point. We replace the hinge and re-weld at the post, and the gate hangs like it did when it was hung.
Pricing for Gate Parts & Welding in Lyndon, KY
Here’s what gate welding work actually costs in Lyndon. A basic hinge replacement on a standard driveway gate typically runs $180-$340, depending on whether we’re replacing one hinge or a full set and whether the post weld needs rebuilding. Post replacement in Lyndon’s clay soil, including cutting out the old footing, setting the new post in concrete, and re-hanging the gate, usually lands between $550 and $1,100 depending on post size and whether the driveway has concrete to cut through. Rail repair and straightening runs $150-$450, more if we’re welding in a reinforced splice. The price is quoted and agreed before any work starts, and it doesn’t change at the door.
We offer $40 off any repair over $200, no trip charge anywhere in Jefferson County, and a permanent 10% discount for seniors and veterans. If another company handed you a written estimate, bring it to us for a free second opinion.
We Also Serve Cities Near Lyndon
We run the same trucks and the same crew through the neighborhoods around Lyndon, including Saint Matthews, Douglass Hills, Middletown, and Buechel. If you’re just across the line, we’ll come to you the same way, with the same 90-Day Promise. See Lyndon for what we fix most often in the 40222 ZIP specifically.
Serving Lyndon, KY - Our Local Coverage Area
We’re based in the Lyndon area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lyndon
Because the hinge post has moved in the clay, not the panel. Lyndon’s expansive soil heaves with every freeze-thaw cycle, and a post set in a shallow footing sixty years ago will shift a little each winter until the gate binds against the latch post. The fix is resetting the post deeper in concrete, not adjusting the hinge. Call (877) 610-2993 and we’ll come check the post before you spend money on opener repairs.
Lyndon’s 40222 ZIP sits under a mature hardwood canopy, and long private driveways mean gates sit directly beneath ice-loaded limbs. When freezing rain hits, ice accumulates on the tree branches, then drops onto the gate below, bending the top rail in a single storm. Combine that with hardware that’s already 30-50 years old, and Lyndon sees rail damage spikes that Saint Matthews or Middletown see less often. We weld and reinforce those rails on site.
Yes, in most cases. A legacy DoorKing, Viking, or Linear operator that predates modern safety standards can often be retrofitted with photo eyes, contact edges, and a new control board that meets current UL 325 requirements. We’ll tell you honestly whether the existing motor and arm are worth keeping or whether a full operator replacement is the smarter spend. Estimates are free at (877) 610-2993.
When the frame itself is rusted through in multiple places, or when the post is so deeply deteriorated that a new post plus rail reinforcement plus hinge replacement totals close to 70% of a new gate’s cost. We give you both numbers on the spot: the weld repair price and the replacement price. Fix the panel without the post and you’ll fix it twice, so if the post is gone, replacement is often the honest cheaper fix.
First, don’t force it with the opener motor. If the gate is loaded with ice or the rail is bent, forcing the motor burns out the gearbox or the control board. Disconnect the operator arm if you can safely reach the release, clear ice weight from the panel with a rubber mallet, and call us at (877) 610-2993. We’ll come out, assess the rail, hinges, and post, and quote the repair before any work starts.
How Lyndon’s Freeze-Thaw Cycle Turns Small Gate Wear into Big Repairs
Louisville’s position in the Ohio Valley ice storm corridor means Lyndon gets freezing rain more often than Cincinnati to the north or Nashville to the south. That’s the single biggest reason gates in the 40222 ZIP fail differently than gates in neighboring markets. Each freeze-thaw cycle moves the clay soil under the hinge posts. Each ice event loads the ornamental iron panel with weight the original 1960s hinges were never built to carry. The posts lean, the top rail bends, and the opener motor burns itself out fighting the misalignment. By the time you notice a sag or a bind, the underlying weld at the hinge post has likely been failing for years.
On one Lyndon property off La Grange Road, our techs found a 1970s swing gate whose hinge post had shifted in the clay-heavy soil after repeated freeze-thaw cycles. The gate was binding hard against the latch post. We cut out the old post footing, reset a new hinge post in concrete, and welded reinforcement plates to the original rail. Then we replaced the worn LiftMaster gate operator’s control board so the gate swings smooth and level again. That’s the Lyndon job in one visit: soil, ice, old hardware, and a weld that holds.
That’s also the distinction that keeps this page honest. Some companies will tell you the gate is beyond saving and sell you a whole new one. Others will weld a patch and ignore the post. We do neither. We tell you when welding saves money, and we tell you when replacement is the cheaper long-term answer. If the post is sound and the rail can be repaired, we save the gate. If the frame is rusted through and the post is leaning, a new gate costs less than three years of patchwork. You get to decide with real numbers in front of you.
If your Lyndon gate is binding, bent, or dead after the last freeze, call us at (877) 610-2993. A live person answers. We’ll give you a straight answer and a written price before any work starts, and the 90-Day Done Right Promise stands behind every weld we make in Lyndon.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lyndon since 2001.