Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Loomis
Gate parts and welding in Loomis usually means one of three things: a hinge post that has heaved out of plumb, a weld that cracked at the hinge post, or an operator that quit because acorns and oak limbs jammed the track again. Hal Gatewood has been fixing those exact problems since 2001, and he does the welding right in your driveway so the gate never leaves your property. If you’re off Val Verde Road, up in the Loomis Basin horse country, or over by the 95650 corridor, call (877) 610-2993 and a live person answers. Not a voicemail. Not a call center. Hal or his crew will be on the phone, and they’ll tell you straight what the repair will take.
Our Gate Parts & Welding team works on ornamental iron driveway gates, heavy steel pipe swing gates, slide gates on gravel drives, and the operators that run them. Loomis is different from Rocklin or Roseville. Here, one property often has both an automated iron entry gate and a livestock gate in the back forty. We service both, same trip, same truck.
When Welding Makes Sense vs. When Replacement Is Cheaper
Here’s the honest math. A cracked weld on a 1-inch square tube frame on an ornamental driveway gate in Loomis typically costs $180 to $320 to grind out, re-weld, and reinforce with a gusset plate. That gate is worth $2,500 to $6,000 new. Welding is the obvious answer. But a rusted-through gate frame where the bottom rail has turned to lace? Welding patches onto compromised steel runs $400 to $700, and you’ll be back in two years doing it again. At that point a new gate panel makes more sense, and we’ll tell you that before you spend a nickel.
The same logic applies to wood hinge posts on 1970s ranch gates. If the post is sound and only slightly out of plumb, we can sometimes re-set it. If the clay-loam soil has heaved it six inches and the wood is punky at grade, replacing the post is the only repair that lasts. Hal doesn’t upsell. He’ll show you the rot, show you the cost both ways, and let you decide with your eyes open.
Why Gatewood Fence & Gate Is Loomis’s Preferred Gate Parts & Welding Company
Hal Gatewood’s name is on the shop, his address is published, and his license number is right there for anyone to look up. He has been at this since 2001. Loomis homeowners tend to appreciate that because most of them have already been burned once by a company that quoted one price on the phone and charged another at the door. Hal quotes a price before the work starts, writes it down, and stands behind it with the 90-Day Done Right Promise: if it’s not done right, one call brings him back, no runaround, no fine print. It’s stamped in writing on every job.
Calls are answered by a live person 24 hours a day, 7 days a week. Not a dispatch queue. Not a chatbot. You call, a human picks up. For Loomis, that matters when a gate won’t close at 10 p.m. and the horses are in the front pasture. We coordinate scheduling from our Sacramento office, but crews serve Loomis locally, so the person who shows up knows the roads and the soil. Our crew members are background-checked and uniformed, and Hal’s certification list covers nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. $40 off any repair over $200, no trip charge inside the county, and a free second opinion on any written estimate are part of how we work. Seniors and veterans get a permanent 10% discount. No haggling needed.
Our Gate Parts & Welding Services in Loomis
Hinge Replacement
Loomis gate hinges fail in a predictable way. The clay-loam soil in the foothill parcels expands through wet winters and contracts through 100°F summers, which tilts hinge posts out of plumb. Then the gate’s full weight hangs on the top hinge, the leaf fatigues, and the gate drags. Hinge replacement in Loomis typically runs $150 to $350 per hinge depending on the gate’s weight and the hinge style, and that includes welding on new barrel or strap hinges and shimming the gate so it swings true. We do not replace a hinge without first checking the post. Fix the panel without the post and you’ll fix it twice.
Post Replacement
This is the job Loomis calls us for most often, and it’s where our local experience matters. Many 1970s-era ranch properties out toward the Loomis Basin have heavy steel pipe gates hung on telephone-pole-diameter wooden posts set in concrete. The decomposed-granite soil underneath lets the concrete footer rock over years, so the post leans and the gate sags. Post replacement in Loomis runs $450 to $900 for a standard 4×4 or 6×6 wood post with a concrete footer, and $600 to $1,200 for heavy steel pipe posts on equestrian gates. The sequence matters: pull the old post, dig the footer deeper, set the new post in fresh concrete, then repack and compact the DG around the base before any weld or hinge adjustment. Skip the DG step and the repair won’t survive one rainy season. Our crew knows to check footer integrity first because that’s what the soil here demands.
Rail Repair
Bottom rails on Loomis gates take the worst abuse. Ranch gates get bowed by livestock pushing against them. Ornamental gates get hit by mowers and gravel kicked up from driveways. A bowed or cracked bottom rail can be sectioned and replaced without rebuilding the whole gate panel. Rail repair in Loomis runs $200 to $400 for most ornamental gates and $300 to $550 for heavy pipe rail on livestock gates, including grinding the old weld points, fitting the new section, and re-welding with proper penetration. We do custom rail fabrication at our shop and on-site welding, so the gate stays in your driveway.
Custom Welding
Sometimes the right fix is making a part that doesn’t exist anymore. We do custom welding for Loomis gates that were fabricated decades ago by a welder who retired before cell phones existed. Cracked scrollwork, missing finials, broken latch plates, damaged gate frame corners: we cut out the bad steel and weld in new material, matching the profile and paint-ready finish. Custom welding on Loomis ornamental gates typically runs $250 to $600 depending on the amount of fabrication and whether we need to jig the gate to keep it square. Hal has welded on gates off Sierra College Boulevard, up toward Penryn and Newcastle roads, and across the Loomis Basin. His crew is certified to service Viking, Ghost Controls, and DoorKing openers, and they weld to match those systems’ mount points.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Loomis
We stock common replacement parts for Loomis customers running Ghost Controls openers on long gravel driveways, Viking operators on slide gates, and DoorKing systems on rural entry gates. We also service LiftMaster, FAAC, BFT, Linear, Elite, and Mighty Mule. Because we keep parts on the truck, most Loomis gate repairs get done in one visit. When an operator is beyond repair, we’ll tell you plainly, then quote a retrofit rather than a band-aid.
Common Gate Parts & Welding Problems We See in Loomis Homes
- Heaved hinge posts on 1970s-era ranch gates. The clay-loam soil here expands and contracts enough to tilt treated 4×4 and 6×6 posts out of plumb over 20 to 40 years. Welding the gate frame won’t fix a leaning post; the post has to be reset or replaced, and the decomposed granite around the footer repacked.
- Acorns and blue-oak limbs jamming slide gate tracks. Loomis parcels are full of valley oaks and blue oaks. After every wind event, acorns roll into rack-and-pinion tracks and strip the gears on older LiftMaster and Viking operators. We clear the debris, inspect the rack, and replace stripped gears before they wreck the motor.
- Fatigued wrought-iron welds at the hinge post. Loomis swings from 100°F summers to freezing winter nights. That cycle makes steel expand and contract, and every cycle stresses the same weld point: where the gate’s full weight loads onto the hinge. Cracks there grow fast, so if you see a hairline crack at the hinge post, get it welded before the gate drops.
- Rust through on the bottom rail of ornamental gates. Near-zero humidity in summer doesn’t save the bottom rail from winter rain and irrigation overspray. We see Loomis gates where the bottom rail has rusted through from the inside while the rest of the gate looks fine. We cut out the section and weld in a new rail.
Pricing for Gate Parts & Welding in Loomis, CA
Here are the actual ranges for typical gate welding and parts repairs in Loomis right now:
- Hinge replacement: $150 to $350 per hinge
- Wood post replacement with concrete footer: $450 to $900
- Heavy steel pipe post replacement (equestrian gates): $600 to $1,200
- Cracked weld repair with gusset reinforcement: $180 to $320
- Bottom rail section replacement: $200 to $400
- Custom welding and fabrication: $250 to $600
- Slide gate track clearing and gear replacement: $200 to $450 for most operators
- Safety sensor retrofit on an existing operator: $275 to $500 per set
What changes the price is the gate’s weight, how much fabrication the job needs, and whether we’re dealing with a wood post that has rotted below grade. Every price is quoted and agreed before any work starts. You’ll never see a surprise on the invoice. Estimates are free, and we give a free second opinion on any written competitor estimate. Call (877) 610-2993 and we’ll talk through your gate over the phone, then schedule a visit if you want eyes on it.
We Also Serve Cities Near Loomis
Our Gate Parts & Welding in Loomis service area also takes us out to Rocklin, Granite Bay, Roseville, and North Auburn. If you’re just over the county line or down the hill in Placer County, we’ll head your way. The same upfront pricing, the same 90-Day Done Right Promise, and the same live person on the phone. Call (877) 610-2993 and tell us where you are.
Serving Loomis, CA - Our Local Coverage Area
We’re based in the Loomis area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Loomis
Because in Loomis, the sag is almost never in the frame. It’s in the post. The clay-loam soil under most 1 to 5-acre parcels expands in winter and contracts in summer, which rocks the post footer out of plumb. A gate sags in the hinge post, not in the middle, and that’s where we start. Welding the frame square again without fixing the post means you’ll have the same sag next spring. Post replacement or re-setting with repacked decomposed granite around the footer is the repair that lasts. Call (877) 610-2993 and we’ll diagnose it over the phone, then confirm on site.
Yes. Most pre-2016 operators around Loomis were installed before UL 325 entrapment protection became the standard on the residential side, so they lack photo eyes and proper edge sensors. We can retrofit an existing LiftMaster, Viking, Ghost Controls, or DoorKing operator with new safety photocells and contact edges, usually for $275 to $500 per set installed. If the operator’s control board is too old to accept modern sensors, we’ll quote a retrofit kit before we ever suggest a full replacement. Call (877) 610-2993 for a free safety assessment.
Yes, and it’s one of the most common jobs we do in the 95650 zip code. Those 1970s ranch gates were built with treated posts that have been in Placer County clay-loam soil for 40 to 50 years, and many have heaved or rotted at grade. We pull the old post, dig the footer deeper, set a new post in concrete, and repack the decomposed granite around the base before welding the hinges. Post replacement runs $450 to $900 for most ranch gate posts. Call (877) 610-2993 and we’ll give you a written price before any work starts.
We do on-site welding for cracked scrollwork, broken hinge welds, bent frame rails, failed latch plates, and rust-through on bottom rails. Our crew welds in the driveway so your gate never leaves the property, and we match the original profile so the repair doesn’t look like a patch. Typical ornamental gate welding in Loomis runs $180 to $600 depending on how much steel needs to be cut out and replaced. Hal Gatewood has been welding these gates since 2001, and his crew carries gear for both MIG and stick work so the weld matches the original material. Call (877) 610-2993 for a quote.
Yes, and it’s a recurring call out here every fall. Loomis parcels are thick with valley oaks and blue oaks, and acorns roll into rack-and-pinion tracks after every wind event, jamming the gate and stripping gears on older LiftMaster and Viking operators. We clear the track, inspect the rack for wear, replace stripped gears, and often add a simple brush seal to keep the worst of the debris out. Track clearing and gear replacement runs $200 to $450 for most Loomis slide gates. Call (877) 610-2993 and mention the oak debris; we’ll bring the right parts on the first trip.
Call Gatewood Fence & Gate for Gate Parts & Welding in Loomis
If your Loomis gate is sagging, cracked, jammed, or just won’t stay closed, call (877) 610-2993. Hal Gatewood’s name is on the shop, his crew is background-checked and uniformed, and every job carries the 90-Day Done Right Promise in writing. You won’t get a call center. You’ll get a live person, a straight answer, and an upfront price before any work begins. Free estimates, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. The shop’s down the road, and the name’s on the door. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Loomis since 2001.