Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Leon Valley
Gate parts and welding in Leon Valley usually come down to one question: can the gate be fixed where it stands, or does it need full Gate Installation - Leon Valley? Most of the time, we fix it right in your driveway. A hinge replacement on a typical Leon Valley wrought iron gate runs $185-$320. A post that has heaved out of plumb costs $340-$680 to cut out, re-set, and weld back square. Call (877) 610-2993 and Hal or one of his crew will give you a straight answer, an honest price before any work starts, and a 90-Day Done Right Promise in writing on every job.
We’ve been welding and repairing gates in Leon Valley long enough to know the 78240 zip code street by street. The ranch-style homes off Poss Road, the 1970s subdivisions along Evers, the corner lots off Bandera Road where the clay never stays still. That local knowledge matters because a gate that sags on one side of Leon Valley is usually failing for the same reason it is failing on the other: the soil under the posts is moving.
Why Gatewood Fence & Gate Is Leon Valley’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001 and his name is still on the door. Not a franchise. Not a middleman. A local owner who answers the phone at 3 a.m. when a gate will not close and a dog is loose. Leon Valley customers call direct and get a live person, 24 hours a day, 7 days a week. No voicemail. No call center three states away.
Our Gate Parts & Welding team has spent years driving the streets of this small, fully enclosed city surrounded by San Antonio. We know where the 1960s ranches sit on postage-stamp lots with shallow footings, and we know which ones have original wrought iron that is now 40 to 60 years old. That is the real story of gate repair in Leon Valley: the town is not building many new gates. The town is holding onto old ones, and the old ones need attention every few years as the clay under them swells and shrinks.
Every job we finish in Leon Valley carries the 90-Day Done Right Promise. If it is not done right, one call brings Hal back. No runaround, no arguing about who is at fault. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.
Our Gate Parts & Welding Services in Leon Valley
Hinge Replacement
Most wrought iron swing gates in Leon Valley do not fail in the middle of the panel. They fail at the hinge post. After 40 or 50 years of Bexar County clay heaving the footing up and down, the post tips 2 or 3 inches off vertical, the hinge pins wear unevenly, and the gate no longer reaches the latch striker. We replace the hinge pins, re-set the post, and weld the bottom rail square so the gate swings true. A hinge replacement with post realignment typically runs $285-$420 in the 78240 zip code.
Post Replacement
The shallow footings used in Leon Valley’s original 1960s and 1970s construction were not built for Texas clay. They were built for somewhere with stable soil. That is why so many gate posts, especially on ranch-style homes between Bandera and Evers, lean a little more every wet-dry cycle. When a post has rot or a cracked weld at the base, or the lean has gotten past what can be shimmed, we cut out the old footing, pour a deeper reinforced base with a gravel drainage collar, set the post plumb, and weld the gate back to it. Post replacement in Leon Valley runs $340-$680 depending on the gate weight and the condition of the surrounding concrete.
Rail Repair
Bottom rails on aging wrought iron gates take the worst of the heat. A hard freeze, like Winter Storm Uri in February 2021, cracks a welded joint overnight. Then the summer sun, with heat indexes above 105°F in this northwest San Antonio corridor, expands the steel until the panel drags on the driveway. We cut out the fatigued section and re-weld it in place, on site, so the gate never leaves your property. Rail repair and re-welding typically runs $150-$310 per rail, and on most Leon Valley gates there are two or three worth checking while we are there.
Custom Welding
Not every fix is a replacement part. On a lot of Leon Valley ranch-style homes, the original ornamental iron has scrollwork that no parts catalog carries anymore. When a scroll cracks or a decorative picket breaks off at the weld, we fabricate the replacement on site and match the old profile. Custom welding work in Leon Valley is billed at $95-$135 per hour plus materials, and the quote is agreed before the welder strikes an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Leon Valley
If your Leon Valley Gate Motor & Opener quits after a cold snap or a summer heat run, we service the brands most common on 78240 driveways: Viking, Ghost Controls, and DoorKing are the three we see most on the residential gates around Bandera and Evers. We also carry a rotating stock of Limit and LiftMaster hinge pins, roller assemblies, and latch hardware. If we do not have the part on the truck, we can usually have it in hand same week. The welding work we do right on site, right where your gate hangs.
Common Gate Parts & Welding Problems We See in Leon Valley Homes
- The gate swings fine but will not latch. This is the classic Leon Valley failure. The hinge post has tilted 2 to 3 inches off vertical because the Vertisol clay underneath heaved during a wet-dry cycle. The gate still moves, but the latch striker is now out of reach. Adjusting the latch alone will not fix it; the post must be re-set.
- The bottom rail cracked at the weld after a hard freeze. February 2021 hit every old weld in the 78240 zip code hard. Cold contracts the steel, the old weld pops, and the gate panel loses its structural triangle. When summer comes, the panel drags and sags worse every month.
- A track-mounted slide gate binds halfway open. The operator post and the rack and pinion track have shifted out of alignment because the clay under each footing is moving at a different rate. The gate will keep binding until both posts are checked and the track is re-leveled.
- Hinge pins are pitted and worn from 40 years of Texas heat cycling. On original 1960s and 1970s gates, the pins were never meant to last this long. The steel fatigues, the pins wear into an oval, and the gate starts to ride lower and lower until it scrapes the driveway apron.
Pricing for Gate Parts & Welding in Leon Valley, TX
Hinge replacement in Leon Valley typically runs $185-$320. Post replacement runs $340-$680 depending on gate weight, footing depth, and how much concrete has to come out. Rail repair or re-welding runs $150-$310 per rail. Custom ornamental welding is $95-$135 per hour plus materials. A full wrought iron gate rebuild, including both hinge posts, panel straightening, and re-welding, usually lands between $700 and $1,200 on a Leon Valley ranch-style home.
What moves the number is the soil. A gate off Poss Road sitting on shallow 1960s footings will need deeper excavation and a gravel drainage collar to keep the new post from tilting again. That is more labor than a simple hinge swap, and it is worth every dollar because it prevents the same repair in two years. Every quote is written down and agreed before work starts. There is $40 off any repair over $200, no trip charge inside Bexar County, and a free second opinion on any written estimate from another company. Seniors and veterans always get 10% off.
Call (877) 610-2993 and we will give you an exact number before we touch a wrench.
We Also Serve Cities Near Leon Valley
Our crews serve Gate Parts & Welding in Leon Valley daily, and we run the same trucks to Lackland Air Force Base, Alamo Heights, Terrell Hills, and surrounding San Antonio neighborhoods. If you’re on the edge of Leon Valley and are not sure whether you’re in our service area, call and ask. A live person answers, day or night.
Serving Leon Valley, TX - Our Local Coverage Area
We’re based in the Leon Valley area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Leon Valley
Because the hinge post is moving, not the latch. Leon Valley’s Vertisol clay swells and shrinks through every wet-to-dry season, and on the shallow footings common in 1960s and 1970s construction, that heave tips the post 2 to 3 inches off vertical. Your gate swings fine, but the post that anchors the strike side has moved. A latch adjustment masks the problem for a season. Re-setting the post, ideally with a deeper base and a gravel drainage collar, is the fix that lasts. Call (877) 610-2993 and we’ll check the post, not the latch, first.
Yes, in most cases we can. The old ornamental iron on Leon Valley ranches, especially the scrollwork and pickets, is usually thicker than anything sold at a big-box store today. If the frame is still solid, we cut out the fatigued rails, straighten the panel, weld in new matching steel, and replace the hinge pins. You keep the original look and the gate stays in your driveway the whole time. If the panel is too far gone, we will tell you straight and quote a replacement that matches the original profile. Free estimate, written down before any work starts.
The hinge post footing is the problem. On 78240 homesites, especially the platted streets from the 1960s and 70s, the original posts were set in concrete that is too shallow, often 18 to 24 inches, while the Vertisol clay around them heaves 2 to 3 inches every season. Welding the sagging bottom rail reinforces the panel, but the post keeps moving, and eventually the panel pulls the repair apart. We fix it by excavating the old footing, setting the post in a deeper reinforced base with a gravel drainage collar, and only then re-welding the gate. Repair the post without the panel and you are chasing half the problem. Repair the panel without the post and you will fix it twice.
Yes. Leon Valley has some acreage-style entrances, especially along the edges of the city and on larger lots that back up to Huebner Creek, where running conduit from the house to the gate is not practical. We install solar-powered operators, most commonly Ghost Controls or Viking units, with a panel sized to the gate’s cycle count and a battery bank that holds through the short winter days. The quote includes the operator, solar kit, mounting hardware, and the post inspection, and the price is agreed before we start. Call (877) 610-2993 for a free site visit and a written estimate.
We set the posts deeper than the original construction, wrap the base in a gravel drainage collar so water does not sit against the concrete and swell the surrounding Vertisol clay unevenly, and we use a heavier gauge hinge assembly than what the 1960s builders installed. On a Leon Valley automatic gate with Gate Access Control in Leon Valley, we also level the operator post independent of the gate post so a small shift in one does not throw the rack and pinion out of alignment. The combination costs a little more up front, but it stops the every-two-years reset cycle that plagues shallow footing gates in the 78240 zip code.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Leon Valley since 2001.