Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lakewood
Gate parts and welding in Lakewood usually means one of three things: a hinge post rotted out at the base, a gate that sags until it drags, or an older operator with a control board nobody makes parts for anymore. Our Gate Parts & Welding team handles all three, and we do the welding on site in your driveway so the gate never leaves your property. Hal Gatewood has been doing this work since 2001, and the person who answers your call is the same person who will show up in Lakewood, not a call center three states away. Call (877) 610-2993 and you’ll get a live person, 24 hours a day.
Why Gatewood Fence & Gate Is Lakewood’s Preferred Gate Parts & Welding Company
Lakewood is a unique place to work on gates. The entire city was planned and built by one developer between 1950 and 1953, and that means the gate openings on original ranch homes repeat block after block. If you live in the 90712 ZIP off Del Amo Boulevard or the 90713 ZIP around Candlewood Street, the odds are good your side-yard gate rough opening is between 38 and 42 inches, with posts set in the same corner position as every other house on the street. We know that before we even pull up. That kind of local knowledge only comes from doing hundreds of repairs in Lakewood, and it’s why we can often quote a hinge post replacement over the phone based on photos you text us.
Hal Gatewood’s name is on the shop and on every invoice. There’s no faceless crew, no rotating subcontractor, no estimate that changes after the job starts. Every repair carries the 90-Day Done Right Promise in writing. If it’s not done right, one phone call brings him back. No footnotes, no fine print, no “in most cases.”
Our Gate Parts & Welding Services in Lakewood
Hinge Replacement
Hinges on a Lakewood swing gate take a beating from two directions at once. The gate’s weight pulls down, and the salt air drifting in from the Long Beach harbor accelerates rust at the weld points. We regularly find hinges that look fine from the outside but have lost half their thickness where they meet the post. For Gate Installation in Lakewood, a hinge replacement typically runs $150 to $350 per hinge, including cutting out the old weld and grinding the post clean before we weld the new hinge in place. We don’t bolt on band-aid plates unless the post is too far gone to weld, and we’ll tell you honestly when that’s the case.
Post Replacement
This is the big one in Lakewood. The marine layer hangs over the city most mornings, and the moisture sits at the base of every gate post where it meets the concrete. After 70 years of that, the bottom six inches of the post can corrode until there’s nothing left holding the gate up. We cut the post out at ground level, break out the old footing, pour a new one, and weld in fresh steel or repair the existing post if there’s sound metal to work with. A post replacement in Lakewood typically costs $400 to $900 depending on post size and footing depth, and we quote the exact number before we start. Fix the panel without the post and you’ll fix it twice.
Rail Repair
When a gate sags in the middle, the rail is usually the victim, not the cause. The hinge post shifts, the rail bends under the gate’s own weight, and then the welds start to crack. We see this constantly on original 1950s gates in the 90714 ZIP near the Lakewood Country Club and in neighborhoods around Mayfair Park. Rail repair in Lakewood runs $250 to $550, which includes welding in a new section of steel, grinding the old welds smooth, and re-aligning the gate so it swings true. The gate sags in the hinge post, not in the middle, and that is where we start.
Custom Welding
Sometimes the part you need doesn’t exist anymore. A 1953 gate with a decorative scroll someone’s kid backed into. A latch mount that was fabricated by the original builder and never reproduced. A bent drop rod that no off-the-shelf part matches. That’s what the welding rig is for. Custom welding in Lakewood starts at around $150 for small repairs and goes up from there depending on material and time. We do it in your driveway and you can watch the work happen. Most of the time the gate doesn’t even come off its hinges.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lakewood
We service and retrofit Lakewood Gate Motor & Opener systems from FAAC, BFT, Linear, and Viking. That’s important in Lakewood because so many homes still have original equipment from the 1950s and 60s, and the control boards on those older units often predate modern safety photocells. We keep common parts stocked for Lakewood customers, which means a lot of repairs get done the first trip. If you have a vintage operator with no parts available, we’ll walk you through whether a retrofit makes sense or if a new operator is the cheaper answer over the next five years. We don’t push replacement when repair is honest work.
Common Gate Parts & Welding Problems We See in Lakewood Homes
- Corrosion at the hinge post base. Salty marine air from the coast just a few miles away speeds up oxidation, and we regularly find posts that are paper-thin at the concrete line. The gate sags, binds on the driveway, and eventually stops latching.
- Obsolete control boards on 1950s-era operators. Many original Lakewood gates have operators whose control boards don’t support modern safety photocells or keypad entry. That means entrapment protection is basically non-functional. A retrofit brings the gate up to current safety standards without replacing the whole operator.
- Worn rack and pinion teeth on slide gates. The original steel gear strips on a 70-year-old Lakewood slide gate wear smooth over time. The gate starts jerking, grinding, and eventually the operator fails trying to move seized hardware.
- Latch and lock failures from misalignment. When the hinge post shifts even a quarter inch, the latch no longer lines up with the post. Homeowners tighten the latch, but the problem is in the post. We align the gate, then replace the latch if it’s been strained past saving.
Pricing for Gate Parts & Welding in Lakewood, CA
Here’s what we typically see in the Lakewood market when our Gate Parts & Welding crew writes up a quote:
- Hinge replacement: $150-$350 per hinge, welded on site
- Post replacement: $400-$900, including new footing and welding
- Rail repair: $250-$550, including weld and realignment
- Custom welding: starts at $150, quoted after we see the part
- Gate rollers and hardware: $75-$300 depending on the roller set and track condition
- Latch and lock repair or replacement: $80-$220
Every price is quoted and agreed before any work starts. There’s no trip charge inside Lakewood and no surprise on the invoice at the door. We also offer $40 off any repair over $200, a free second opinion on any written estimate you got from another company, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll give you a real number over the phone if you can send a few photos.
We Also Serve Cities Near Lakewood
Our crews work throughout the area around Lakewood, including Signal Hill, Bell, Bellflower, and Long Beach. The marine air affects gates in all of them, though Long Beach and Bellflower grew organically over decades and don’t have the same uniform 1950s gate footprints that make Lakewood repairs more predictable. If you’re right across the city line, the same crew that works Lakewood will be the one that shows up.
Serving Lakewood, CA - Our Local Coverage Area
We’re based in the Lakewood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lakewood
If the post has lost more than about a third of its thickness at the base, or if you can push a screwdriver through the metal near the concrete line, replacement is the honest answer. We’ll grind off the surface rust to inspect the steel, show you what we find, and give you both options with prices before we touch anything. In Lakewood, the marine air makes base corrosion worse than in inland cities, so we’re cautious about welding repairs onto metal that’s already compromised. Call (877) 610-2993 and we’ll inspect it for free.
Because the hinge post is moving, not the hinges. The gate sags in the hinge post, not in the middle. Decades of salt air have probably rotted the post below grade, and no amount of hinge tightening will fix a post that’s shifting in its footing. We replace the post, set a proper footing, and the sag stops for good.
Yes, in most cases. We can often mount a modern operator onto the existing gate and replace the old control board with one that supports current safety photocells and keypad entry. The retrofits we do in Lakewood are quoted as a package, and they bring a 70-year-old opening up to current safety standards with modern Gate Access Control - Lakewood features without replacing the whole gate. Call (877) 610-2993 and we’ll look at what you have.
Usually it’s the rack, especially on original 70-year-old steel gear strips that have worn smooth. The operator is working fine, but it’s fighting a rack with no teeth left. We replace the rack and often the pinion gear at the same time, which in Lakewood runs $350 to $700 depending on gate length and accessibility. Fixing it sooner is cheaper than replacing the operator after it burns out.
Yes, on the original 1950s homes the side-yard gate rough openings are almost always 38 to 42 inches wide with posts set at the same relative corner position. That means we know the post size, hinge layout, and rail dimensions before we arrive. We pre-stock the common parts and can usually templated a repair across hundreds of homes, which is why our Lakewood turnaround is faster than in neighboring cities where every opening is different.
If your gate is dragging, grinding, or listing toward the driveway, call (877) 610-2993. A live person answers, we’ll give you a real price, and the person who shows up will be someone whose name you can look up. That’s how we’ve worked Lakewood for over two decades, and that’s not changing.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lakewood with gate parts and welding since 2001.