Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lake Worth
Gate parts and welding in Lake Worth costs between $175 and $2,800 depending on what failed. Most repairs run $275 to $650 for hinge and post work, while full post replacement with custom welding lands between $900 and $2,800. We can usually have someone to your driveway within 24 to 48 hours, and the price you hear is the price you pay before we ever pick up a welder. Call (877) 610-2993 and you’ll get Hal Gatewood or one of his crew, not a voicemail.
We know what the salt air off the Lake Worth Lagoon does to gate iron after a few South Florida summers. Our Gate Parts & Welding team has been cutting out rusted posts, re-welding sagging panels, and replacing failed operator boards across 33460, 33461, 33462, and 33463 since long before the current wave of HOA gate overhauls started stacking up.
Why Gatewood Fence & Gate Is Lake Worth’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and his name is on every invoice. When a Lake Worth HOA calls about a gate dragging across pavers or a control board that died after a storm, the person who answers is the same person you’ll see holding a welding torch in your driveway. No dispatch queue in another state. No call center script.
Our customers in Lake Worth keep calling back because we fix the post before we weld the panel. That sounds obvious, but most national outfits weld a patch over a rotten footing, collect the check, and disappear. Then the gate sags again in eight months and you’re paying twice. Our crew resets the post, welds it square, and the gate stays put. We back every job with the 90-Day Done Right Promise, in writing, no fine print.
We’ve done post replacement and hinge work at communities along Hypoluxo Road, inside 33462 subdivisions off Lake Worth Road, and at older bungalow lots east of I-95 in the 33460 corridor. A live person answers 24/7, and there’s no trip charge inside Palm Beach County. $40 off any repair over $200, plus a permanent 10% discount for seniors and veterans.
Our Gate Parts & Welding Services in Lake Worth
Post Replacement
In Lake Worth’s western neighborhoods, gate posts rot at the hinge post footing. Decades of standing water, salt spray, and lawn irrigation saturate the concrete collar, rust creeps up the base, and the whole gate starts leaning. We cut out the failed section, remove and replace the footing, and weld in a new galvanized or powder-coated post. Welding the panel without resetting the post is the most common waste of money we see. A typical post replacement in Lake Worth runs $400 to $1,100 depending on depth, fence material, and whether the post supports a heavy estate gate or a light walk gate.
Hinge Replacement
Hinges are the first casualty of salt air and rain. We see it constantly in Lake Worth’s gated communities: the hinge pin seizes, the leaf cracks, and the gate starts binding or popping on the operator. We replace hinges with marine-grade stainless or coated steel meant for Florida coastal conditions, then re-align the gate so the operator isn’t fighting an off-square panel. Hinge replacement in Lake Worth typically runs $175 to $450 per hinge, including removing and re-welding the leaf. Packing a gate with cheap hardware store hinges is a false economy we refuse to install.
Rail Repair
Slide gates in Lake Worth’s older industrial and warehouse stretches take a beating from coral-rock dust, rain, and long daily cycles. The rail wears, the carrier wheels slop, and the gate starts chattering. We straighten, reinforce, or replace rails and rollers, then re-level the gate so the operator isn’t burning through its limit switches. Rail repair work in Lake Worth usually lands between $300 and $900 depending on rail length and whether we’re replacing the carrier assembly or just rebuilding what’s there.
Custom Welding
Sometimes the gate you have is the gate you want, and it just needs surgery. We do on-site custom welding at the gate, not in a shop three towns over. That means cutting out a cracked picket, reinforcing a failing corner, building a new mounting plate for an operator, or fabricating a custom bracket for a keypad you want moved. We don’t haul your gate away unless it’s truly beyond saving. Custom welding in Lake Worth typically runs $200 to $1,200 depending on the extent, and Hal will look you in the eye and tell you if a new panel is actually the smarter money. The repair-first call is his default.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lake Worth
We service and stock parts for the operator brands installed in dozens of Lake Worth HOA communities: DoorKing, Linear, and Viking are the common ones on older build-out systems, and we carry replacement control boards for the Linear and Elite units that went into the 1995-2005 gated developments. We also work on LiftMaster and Ghost Controls builds from more recent retrofits. Having boards on the truck matters here because a single Lake Worth thunderstorm can knock out a control board and leave an entire community’s front gate stuck open or closed. We don’t want you waiting a week on a part that we should have had yesterday.
Common Gate Parts & Welding Problems We See in Lake Worth Homes
- Rusted hinge post footings from salt spray and standing water. Western Lake Worth HOAs near the lagoon and Intracoastal see the worst of it. The gate sags, the operator groans, and the panel drags across pavers. Fixing the panel alone is a band-aid; the post has to be reset.
- Failed control boards after summer lightning storms. Palm Beach County gets near-daily summer strikes, and a close hit on a western Lake Worth community takes out the operator logic board before the surge protector reacts. We stock replacement boards for the Linear and Elite models still running on dozens of those properties.
- Missing conduit and power runs in older east-of-I-95 lots. Homes built in the 1920s through 1960s along the Lake Worth urban core rarely have conduit buried for a future automatic gate. Adding automation means trenching, pulling wire, and welding a mounting plate onto existing iron.
- Worn slide gate rails and carrier wheels on high-traffic commercial entrances. Lake Worth’s older commercial corridors along Dixie Highway and Lake Worth Road see slide gates cycling hundreds of times a day. Rails wear, wheels slop, and the gate starts binding. Rebuilding the rail is cheaper than replacing the entire operator.
Pricing for Gate Parts & Welding in Lake Worth, FL
We quote every Lake Worth job upfront, before any work starts. You’ll hear the number over the phone, and it won’t change when the crew shows up. Here’s the Lake Worth market reality: hinge replacement runs $175 to $450 per hinge, rail repair lands between $300 and $900, custom welding typically costs $200 to $1,200, and post replacement is the big-ticket job at $400 to $2,800 depending on depth, materials, and access. We don’t pad the hours. We don’t “find” problems that aren’t there. If another company gave you a written estimate, bring it to us and we’ll give you a second opinion for free. Seniors and veterans always save 10%, and any repair over $200 automatically takes $40 off. Call (877) 610-2993 for an exact quote on your gate.
We Also Serve Cities Near Lake Worth
We handle the same gate parts and welding work for neighbors in Greenacres City, Lake Worth Corridor, Palm Springs, and Lantana. If you’re just outside the Lake Worth line, you still get the same on-site welding, the same no-trip-charge policy, and the same live person answering the phone. Our Lake Worth customers often refer us to HOA friends in the surrounding communities, and we’re glad to come out.
Serving Lake Worth, FL - Our Local Coverage Area
We’re based in the Lake Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lake Worth
Lake Worth sits next to the Intracoastal Waterway and the Lake Worth Lagoon, so the air carries salt that accelerates corrosion on hinge pins, lock hardware, and post footings. Combined with 60+ inches of annual rain and heavy UV exposure, painted steel can oxidize through standard coatings in five to seven years. The fix is marine-grade stainless hinges, sealed or galvanized post footings, and powder-coated components that won’t fail in two seasons. Call (877) 610-2993 and we’ll inspect your gate for free.
Yes. We’ve worked on multiple master-planned HOA communities in the 33449 and 33467 ZIP codes where original gates from the 1995-2005 build-out are hitting replacement age simultaneously. One crew handles the post resets, hinge replacements, and custom fabrication in sequence, and the HOA gets one written price before the first torch lights. We coordinate with your management company so access roads stay open and residents aren’t locking out. Call (877) 610-2993 to schedule a walk-through.
We have to see the post before we answer that. In Lake Worth’s western communities, a sagging gate is usually a post failure at the footing, not a panel problem. If the weld is cracked but the post is still square and solid, we’ll weld and reinforce. If the post has rotted or shifted at the base, re-welding the panel is a temporary fix and we’ll tell you that before taking your money. Post replacement in Lake Worth runs $400 to $2,800, and the welded panel goes back on the new post. Call (877) 610-2993 for a free assessment.
Yes, it’s a common job in Lake Worth’s older neighborhoods east of I-95. We trench and run the necessary electrical conduit from your panel to the gate, install the operator mounting plate, and weld it to the existing iron. We handle the whole power run ourselves so you’re not coordinating between an electrician and a welder. The full installation including conduit, operator, and safety edges typically runs $1,800 to $6,000 depending on distance and access. Call (877) 610-2993 for a written quote.
Lightning strikes in Palm Beach County hit close enough to gate operator control boards that the surge jumps through the power feed and fries the logic. We see it most often in western Lake Worth HOA communities where operators from the 1995-2005 build-out are still running original boards. We custom-install surge protection and ground the operator correctly, and we stock replacement boards for the Linear, Elite, and DoorKing units still most common in those communities. If your gate operator moves but won’t respond to the board, that’s a classic storm hit. Call (877) 610-2993 and we’ll come out.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lake Worth since 2001.