Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Fremont
Gate parts and welding in Fremont usually come down to one question: fix the post or replace the whole gate. Most of the time we repair what’s there. A typical hinge replacement runs $160-$290, a new galvanized gate post runs $280-$520, and custom on-site welding starts at about $145 for the first hour. We’re Hal Gatewood’s crew, we’ve been fixing gates since 2001, and we’ll weld in your driveway so the gate never leaves your property. Call (877) 610-2993 and a live person answers, any hour.
Why Gatewood Fence & Gate Is Fremont’s Preferred Gate Parts & Welding Company
Fremont is not one market. It’s four ZIP codes with very different gate problems. The western edge along the bay in 94555 eats steel hardware alive. Mission San Jose in 94539 runs on HOA clocks. Central Fremont in 94536 and 94538 is where we see the 1960s and 70s wrought-iron originals finally giving up. We know the difference because we work all of them, every week.
When a Fremont customer calls, they get Hal or someone who works directly for him. Not a phone tree. Not an out-of-town dispatcher who’s never seen a bay breeze rust a gate post in five years. Our reputation here is built on showing up when we say we will and fixing the gate without inventing work. Every job carries the 90-Day Done Right Promise in writing.
Pricing is quoted and agreed before any work starts. That’s a promise, not a sales line. Seniors and veterans get 10% off, always. And if you have a written estimate from another company, we’ll give you a free second opinion.
Our Gate Parts & Welding Services in Fremont
Hinge Replacement
In Fremont’s bay-side neighborhoods, the hinge is rarely the whole problem. Salt air creeps into the weld where the hinge meets the post, and rust does what rust does. We cut the old hinge off, clean the post, and weld on a new one with stainless hardware. If the post itself is too far gone, we’ll tell you before we touch the torch. A hinge that’s just tired can often be replaced for $160-$290, with the gate held true while we work.
Post Replacement
This is the repair that separates a fix from a redo. Gate panels sag because posts rot at the footing, not because the panel bends. In Fremont’s 94555 and western 94536, bay air accelerates this by years. We dig out the old post, set a new galvanized post in concrete, and weld it proper. A typical post replacement here runs $280-$520 depending on depth and what the old concrete looks like. We don’t swap the gate if the gate’s fine.
Rail Repair
Bottom rails on Fremont’s older wrought-iron gates tend to rot from standing water and road splash. When a top or bottom rail separates, we weld it back in place and often add a reinforcing plate so it doesn’t happen again. On HOA-spec tubular steel gates in Ardenwood and Warm Springs, we match the profile so the repair doesn’t stand out. Rail repair keeps the panel square and keeps the gate off the ground.
Custom Welding
Some Fremont gates are not stock. They’re custom-built for a specific opening, or they’ve been modified three times since 1972. We weld on site, in the driveway, with portable equipment that handles both steel and aluminum. If a bracket needs to be fabricated, we fabricate it. If a latch needs to reach a different post, we weld it where it belongs. And since our Gate Parts & Welding work all happens at your property, you can watch the gate get fixed and ask questions while it happens.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Fremont
We service and weld parts for Gatewood’s certified brand line, including Ghost Controls, DoorKing, and Elite. When a Fremont gate has a Ghost Controls arm with a cracked mounting tab or a DoorKing loop detector that’s corroded through, we can weld the bracket, replace the part, or rewire the run, all on site. We stock common parts for these brands in our service vehicles, so a Fremont job usually doesn’t wait on a shipment.
Common Gate Parts & Welding Problems We See in Fremont Homes
- Salt-corrosion at hinge posts and welds. In 94555 and western 94536, gate posts rot at the footing within 5-7 years, not the 15-20 you’d get inland. Our crew sees this constantly; it’s the number one welding call on the bay side.
- Slide gate rollers that seize. Marine particulate mixes with grease on HOA-spec tubular steel gates in Ardenwood, and the rack strips or the roller bearings seize. If the motor isn’t grinding yet, a roller rebuild usually saves the whole operator.
- Mission San Jose HOA delays making problems worse. A bad hinge or loop issue can sit for weeks while an HOA architectural committee mulls it over. Meanwhile the gate panel warps or the post rotates. We quote with that lag built in, so the customer knows the real cost of waiting.
- Photocell and loop detector faults from gate movement. When a Fremont gate sags just half an inch, the safety photocells fall out of alignment and the gate reverses or refuses to close. Fixing the post or hinge usually fixes the “electronic” problem too.
Pricing for Gate Parts & Welding in Fremont, CA
In Fremont, a hinge replacement runs $160-$290. Post replacement runs $280-$520 for a typical driveway gate. Rail repair runs $140-$340 depending on how much weld we need to lay. Custom welding time is $145 for the first hour and $110 for each hour after. The quote includes everything: labor, parts, and any prep. You’ll know the price before we start and it won’t change at the door. If the gate needs a part we don’t carry, we’ll tell you the part cost up front, not after the fact.
We Also Serve Cities Near Fremont
Most of our Fremont work comes from referrals in Newark, Union City, Hayward, and Fairview. If you’re in one of those towns, or anywhere nearby, the trip is short and we don’t charge a trip fee inside the county. Fremont is the core of our service area, but we’re on the road in all the neighboring towns most days.
Serving Fremont, CA - Our Local Coverage Area
We’re based in the Fremont area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Fremont
Because Fremont’s bay-side ZIPs get direct marine airflow off San Francisco Bay, and that air carries salt particulate that settles on unpainted steel. The salt accelerates galvanic corrosion where the hinge post meets the concrete footing, which is where moisture already collects. In 94555 and western 94536, a painted steel post can fail in as little as 5-7 years. Inland cities like Pleasanton don’t get that same salt load. Galvanized posts with stainless fixings last far longer here. Call (877) 610-2993 for an on-site assessment and a quote that won’t move.
Yes, if it’s a repair to existing hardware and you’re not changing the gate’s appearance. Welding a new hinge onto the same gate panel in the same position is a repair, not an architectural change. However, Mission San Jose HOAs handle this inconsistently. Some want written notice of any structural work. We’ve done hinge swaps in 94539 without review, and we’ve waited three weeks for a committee. We’ll help you figure out exactly what your HOA requires so you don’t get a fine over a hinge. Call (877) 610-2993 and we’ll walk you through it.
Usually the roller track and bearings go first. Marine air gets into unsealed bearing housings on tubular steel gates, and the grease turns into a grinding paste. The motor then draws more current and burns out prematurely. That’s why we inspect rollers and rack teeth before touching the operator. Fixing the rollers first often saves the motor entirely. Call (877) 610-2993 for a free estimate on slide gate repair in Ardenwood or anywhere in 94555.
Yes, absolutely. A weld repair that changes the gate’s angle by even half an inch will throw off the safety photocell alignment and the loop detector’s field. The gate will start reversing for no reason or refuse to close. That’s why we re-check sensors after every weld. If you have a Ghost Controls, DoorKing, or Elite operator, we’ll make sure the gate works with it, not against it. Call (877) 610-2993 and we’ll schedule it.
On the bay-side of Fremont, painted steel is a losing bet. Salt air finds every pinhole in the paint and starts eating the steel underneath. Galvanized steel is coated in zinc, and zinc corrodes sacrificially instead of the steel. For posts set in concrete near 94555 or western 94536, galvanized with stainless steel hinges is the specification that actually lasts. We’ll quote both options honestly, but our recommendation for bay-facing homes is galvanized every time. Call (877) 610-2993 for an exact quote.
Contact Gatewood Fence & Gate for Gate Parts & Welding in Fremont
If your Fremont gate is sagging, binding, or rusting through, call (877) 610-2993. A live person answers. We’ll schedule a time, show up in the window we promised, and quote the job in writing before any work starts. No trip charge inside the county. $40 off any repair over $200. And the 90-Day Done Right Promise is stamped on every invoice: if it’s not done right, we make it right. One call, and you’ll see a name you can verify. Hal’s name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Fremont since 2001.