Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Firestone
Gate parts and welding in Firestone, CO usually means one of three things: a hinge post that has rotated in its footing, a builder-grade operator that stripped its gears after one good wind season, or a gate that was installed manual and now needs a motor. We fix all three in your driveway, with the gate staying put. Hal Gatewood has been running Gatewood Fence & Gate since 2001, and when you call (877) 610-2993, you get a live person, not a recording. Our crews know Firestone’s streets, its HOAs, and the specific way its gates fail. We’re not guessing from a map.
Why Gatewood Fence & Gate Is Firestone’s Preferred Gate Parts & Welding Company
Most gate repair companies want to sell you a new gate. Hal would rather fix the one you have. That’s the whole point of our Gate Parts & Welding operation: weld on site, replace only the part that actually failed, and stand behind it. Our 90-Day Done Right Promise is printed on every invoice. If it isn’t right, one call brings Hal back. No runaround.
Firestone homeowners deal with wind load that most front-range towns never see. A gate that sags after two seasons wasn’t built wrong by accident; it was built to a spec that couldn’t handle 60 mph gusts from the west. We see the same stripped gearboxes, the same sheared hinge bolts, the same rotated posts, block after block, because the builders used the same hardware everywhere. Hal’s crew has been through these neighborhoods enough to know which gates will fail before they do. That’s not marketing. That’s 29 years of doing this work with his name on the shop.
Every call is answered by a person, 24 hours a day. Not a voicemail, not an overseas call center. Hal’s cell number is on the invoice. If you want to look a person in the eye before they touch your gate, his shop address is published, along with his license number. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Our Gate Parts & Welding Services in Firestone
Hinge Replacement
A sagging gate is almost never a sagging gate. It’s a hinge failure, or a hinge post that has moved. In Firestone’s post-2005 neighborhoods, we regularly find hinge posts set in shallow footings that let the post rotate under repeated downslope wind. The gate then drags on the driveway and tears up the operator’s rack and pinion. We cut out the old hinge, weld in a new reinforced hinge with a longer leaf, and reset the post in a deeper concrete footer so it stays plumb. Hinge replacement on a Firestone driveway gate typically runs $225-$480, depending on gate weight and post condition.
Post Replacement
This is the repair that separates a real fix from a patch job. Fix the panel without the post and you’ll fix it twice. In Firestone, the open high-plains exposure means a gate post acts like a sail lever every time the wind kicks up. Posts installed during the 2005-2020 buildout were often set in 18 to 24 inches of concrete, which is fine for a fence post and useless for a 300-pound gate. We cut the old post at the base, core out the footing, and set a new, heavier post in a full-depth concrete pour, then weld a reinforcement plate at the top rail. Post replacement in Firestone usually lands between $380 and $750, including the new post, concrete work, and re-hanging the gate.
Rail Repair
Top and bottom rails take the twist load when a gate is racked by wind or by a hinge that’s come loose. We see cracks at the weld joints, rust-through on ornamental steel, and rails bent so far the gate binds. We fix rails by cutting out the damaged section and welding in new steel, then re-aligning the gate so it swings true. On a Firestone steel gate, rail repair is typically $180-$360. If the damage is structural enough that the gate is compromised, we’ll tell you straight, and we’ll quote the replacement before we start.
Custom Welding
Some gates need more than a part swap. A 14-foot brick-column swing gate with a decorative arch, or a custom driveway gate that was fabricated by a shop that no longer exists, needs someone who can weld to the gate you already own. Hal has been welding on site since 2001, and that’s not a sideline, it’s the core of how we keep gates out of the landfill. Custom welding jobs in Firestone typically start around $250 for a single reinforcement repair and run up from there depending on steel footage, gussets, and whether we’re fabricating a bracket or filler piece on the truck or in the shop. We quote it before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Firestone
We’re certified to service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers nearly every gate opener installed in Firestone’s HOA communities, from entry-grade swing arms to the heavier commercial slide operators. We keep common FAAC and Linear replacement parts on the truck, including rack sections, limit switches, and safety photocells, so most Firestone repairs happen in one visit rather than two. If you’ve got a Viking operator that’s starting to hesitate, or a BFT board that throws error codes after a hard freeze, we can usually diagnose it on the spot. You don’t want to wait a week for a part when your gate won’t close at night.
Common Gate Parts & Welding Problems We See in Firestone Homes
- Rotated hinge posts from wind load. Firestone sits flat and open with no windbreaks between the town and the foothills. Every downslope event pushes on your gate like a lever, and the shallow footings common in 2000s tract builds just let go. The gate sags, the latch stops catching, and the operator starts fighting itself.
- Stripped plastic gearboxes in builder-grade operators. We find the same failure across entire cul-de-sacs. Subfreezing nights followed by 55-65°F afternoons make the gears brittle, then the next 60 mph gust strips the teeth. The gate locks mid-swing or creeps off its limit. Half the time, the operator wasn’t heavy enough for a gate that size to begin with.
- Missing or undersized conduit runs. A lot of Firestone’s post-2005 homes got a gate installed manual, no conduit run, no low-voltage line, no plan for automation. When you decide to add a keypad or a motor, there’s no power at the gate. We trench a proper line, lay the conduit for both line voltage and low-voltage controls, and wire it to code.
- Freeze-thaw fatigue at welds and pivot points. Metal expands and contracts every time Firestone swings 40 degrees between night and afternoon. Over a few winters, you get micro-cracks at the weld toes and the pivot pins start wallowing out their holes. Left alone, a top rail crack turns into a snapped gate. Caught early, it’s a 20-minute weld repair.
Pricing for Gate Parts & Welding in Firestone, CO
Here’s what we actually charge, because you should know before you call.
- Hinge replacement: $225-$480
- Post replacement (with deeper concrete footing): $380-$750
- Rail repair / crack welding: $180-$360
- Custom welding / reinforcement: $250+ depending on steel and scope
- Operator swap (builder-grade to heavier unit, installed): $650-$1,400 depending on brand and gate size
- New power/conduit run to an unpowered gate: $400-$900 typical for a residential trench
What changes the price: gate weight, post condition, whether you’re in a gated community with a longer service path from the truck, and whether the operator or rail needs a heavier replacement. We don’t show up and change the number. Every price is quoted and agreed before any work starts, in writing. If you’ve got another written estimate, bring it. Hal will give you a free second opinion, and if it’s a repair over $200, you’ve already got $40 off our price. There’s no trip charge anywhere in Weld County. Seniors and veterans always get 10% off.
We Also Serve Cities Near Firestone
Our Gate Parts & Welding crews run through Firestone every week, and we also cover Frederick, Fort Lupton, Erie, and Lafayette. If your property is a couple minutes outside Firestone, don’t assume that’s a dealbreaker. The same truck that’s in your neighborhood covers those towns too. We know Firestone and the surrounding area because our technicians are local, not driving up from a hub an hour away.
A Wind Event We All Remember
Last March, we got called to a home in the Barefoot Lakes community off Colorado Boulevard after a windstorm left a decorative steel driveway gate hanging off its top hinge. The builder-grade operator had stripped its internal gear, and the hinge post had rotated in its footing. We reset the post in a deeper concrete pour, welded a reinforcement plate at the top rail, and swapped the operator for a heavier LiftMaster with a safety photocell. Came back the next week to do three neighbors with the same damage. That’s Firestone. When one gate goes down, the cul-de-sac follows.
Serving Firestone, CO - Our Local Coverage Area
We’re based in the Firestone area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Firestone
Firestone’s master-planned communities built between 2005 and 2020 share nearly identical swing-gate operator specs, so one hard winter or one severe wind season shears the same gears across a whole cul-de-sac within weeks of each other. We absolutely do bulk repair runs. If three or four neighbors on the same block need operator swaps, hinge post resets, or weld repairs, we schedule them together. It cuts the trip time and keeps the cost per gate down. Call (877) 610-2993 and tell us how many gates are down. We’ll quote it straight.
Most of those gates have no conduit and no power run, because the original build never anticipated automation. You’ll need a trench from the nearest exterior outlet or panel to the gate post, conduit for line voltage and low-voltage controls, and often a deeper post or a reinforcement plate to handle the operator’s torque. We do all of that: trench, wire, post work, operator, safety photocells, keypad. Plan on the power run and conduit being the part that adds the most labor.
The top hinge, almost always. A 60 mph gust hitting a 300-pound gate torques the top hinge first, whether it shears the bolt or pulls the post out of plumb. Once the top hinge goes, the gate hangs off the bottom hinge and the whole panel rakes. We replace top hinges with a longer leaf and a heavier pin, and we check the post’s footing at the same time. If the post moved, the hinge will fail again no matter how good the hinge is.
Yes, you can run a trickle-charge line to a solar opener, and in Firestone’s winter, you’ll probably want to. Solar panels underperform here from November through February, with short days, low sun angle, and freeze-thaw temps that sap battery capacity. A direct line keeps the opener reliable when the panel can’t keep up. We can also add a low-voltage run just for battery maintenance while the panel carries the daytime load. Every lot is different. We’ll look, measure, and quote it free.
Walk out and watch it open from the street side. Look for the gate dragging at the bottom of its arc, which means the hinges or the post have already started to move. Listen for a hard chatter or a grinding noise from the operator, which means the plastic gears are stressed from the cold. Check the latch. If it’s not catching squarely, something in the structure shifted. If you see any of that, call us before the next wind event finishes the job. A $40 visual check is cheaper than a snapped post.
Call Gatewood Fence & Gate for Gate Parts & Welding in Firestone, CO
If your gate is starting to sag, dragging, or making a noise it didn’t make last year, don’t wait for the next Chinook wind. Call (877) 610-2993. You’ll get a live person, not a voicemail. We’ll come out, look at the gate, and give you a written price before we touch it. Free estimates, no trip charge in Weld County, and $40 off any repair over $200. If you’re over 65 or a veteran, that’s another 10% off. Hal’s name is on the invoice, and the 90-Day Done Right Promise means he’ll be back if it isn’t right. Firestone deserves a gate company that fixes things properly, not one that swaps in a new problem.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Firestone and Weld County since 2001.