Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Firestone
A new gate installation in Firestone, CO typically runs $3,800 to $11,500 depending on gate type, automation, and site prep. Most driveway gate work takes one to three days once materials are on hand, and we quote every Firestone job in writing before the first hole gets dug. Call (877) 610-2993 and you’ll get a live person, not a voicemail tree.
We work in Firestone’s HOA communities every week. Booth Farms, St. Vrain Ranch, Barefoot Lakes, Mountain Shadows, the neighborhoods off Colorado Boulevard. We know the builder-grade operators that came with these homes, we know the post footings that never got deep enough, and we know what a 60 mph Chinook wind does to both. That changes how we install. Hal Gatewood has been putting gates in for over two decades, and a big part of that work now happens right here in Firestone. The name is on the shop, the shop is down the road, and the person who answers the phone is the one who signs the invoice.
Why Gatewood Fence & Gate Is Firestone’s Preferred Gate Installation Company
Firestone homeowners tend to call us after someone else’s gate has already failed once. That’s not a complaint; it’s how most of our local relationships start. Hal has been owner-operating Gatewood Fence & Gate since 2001, and he answers the phone himself. When you call about a Gate Installation, you are speaking to the person who will stand in your driveway and look at your post footings. That matters in a community like Firestone where so much housing stock was built in the same decade, by the same builders, to the same spec. We see the same failure modes on the same streets, and we know what to do about them before the wind season hits again.
Our reputation in Firestone comes from doing work that stays done. We publish our address. We stamp a 90-Day Done Right Promise in writing on every invoice. We don’t hide behind a call center three states away. When a Firestone customer calls at 9:30 on a Saturday night because a gate won’t close and the dog is loose, Hal or one of his crew picks up. These are the things that build trust in a town where the person at the hardware store knows your name.
Our Gate Installation Services in Firestone
We install and automate every common gate type in Firestone. The three we do most here are swing gates, driveway gates, and pedestrian gates, and each has its own local quirks.
Swing Gate Installation in Firestone
Swing gates are the most common driveway gate in Firestone’s post-2000 HOA neighborhoods, and they are also the gate most likely to fail from wind. We install single and double swing gates with operators spec’d for sustained downslope gust loads, not just the gate’s weight. A standard single swing gate with automation runs $4,200 to $7,800 in Firestone. We set hinge posts in deep footings with rebar cages, because we have pulled too many shallow posts out of Firestone clay after freeze-thaw cycles.
Driveway Gate Installation in Firestone
A new driveway gate in Firestone should account for wind loads and vehicle frequency before anything else. We handle ornamental steel, aluminum, and wood hybrid driveway gates, and we size the operator for the actual use case: a household with three drivers and regular deliveries needs a heavier cycle rating than a weekend-use secondary driveway. We also handle the power run and conduit. Many Firestone homes were built without any provision for gate automation, and we’ll get into that more below.
Pedestrian Gate Installation in Firestone
Pedestrian gates in Firestone usually serve HOA amenities, side yards, or access paths alongside a driveway gate. A well-installed pedestrian gate with a magnetic lock or keypad entry for Firestone runs $1,600 to $3,400. We set these with the same post-depth standards as driveway gates; a pedestrian gate that drags after two winter freeze-thaw cycles is a post problem, not a hinge problem.
Adapting to Firestone’s Wind and Weather
Firestone sits on flat, open terrain with no windbreak between the town and the foothills. That means Chinook downslope events hit the area with sustained gusts that routinely exceed 60 mph. In some of the newer developments off WCR 24 west of I-25, entire blocks share the same exposure. We account for this in every gate we install: heavier post footings, operators with higher torque ratings, reinforced hinge plates, and wind-rated hardware. A gate installed to Denver standards simply will not hold up in Firestone.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Firestone
We are certified to service and install nine major gate brands, and we keep the most relevant parts on the truck for Firestone jobs. For the builder-grade communities here, we commonly replace underbuilt LiftMaster operators with heavier-duty FAAC and Viking units. For more modern systems, we work with Linear, DoorKing, Ghost Controls, and others. Hal has been inside thousands of these operators since 2001, and he will tell you the truth about which ones hold up in Weld County wind. When a Firestone gate fails, we fix it in the driveway with on-site welding; we don’t haul it back to a shop for a week. Repair before replace. That’s the whole philosophy.
Common Gate Installation Problems We See in Firestone Homes
- Builder-grade swing operators stripped by wind. Entire cul-de-sacs in Firestone were built with the same entry-level swing gate operators. After one severe Chinook season, we routinely find the same stripped-gear failure in a dozen homes at once. The operator was simply never spec’d for 60 mph gusts.
- Hinge posts rotating in shallow footings. Original post footings in many Firestone communities were cut shallow to speed construction. Freeze-thaw cycling in the clay soils slowly works the post loose until the gate sags and stops latching. A sagging hinge post means the footing failed, not the panel.
- No UL 325 entrapment protection. Many early-2000s HOA spec gates were installed without safety photocells or loop detectors. Code has changed since then, and communities are noticing. If an automatic gate in Firestone lacks entrapment protection, it is not just a code violation; it is a safety problem.
- No power or conduit to the gate location. This is the big one for Firestone. Builders rarely ran electrical to the driveway line, so automating a manual gate usually means trenching and a proper power pull. We quote the electrical run in writing before we start.
Pricing for Gate Installation in Firestone, CO
Honest numbers for Firestone, as of March 2026:
- Swing gate, single, without automation: $2,600 to $4,800
- Swing gate, single, with automation (heavier-duty operator): $4,900 to $7,800
- Driveway gate, double swing with automation: $7,500 to $11,500
- Pedestrian gate with keypad or maglock: $1,600 to $3,400
- Power/electrical run from panel to gate: $1,100 to $3,200, depending on distance and trenching conditions
We quote every Firestone job in writing before work starts, and the price does not change at installation unless the scope changes and we agree on the change first. No trip charge inside Weld County. Free second opinion on any written estimate. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 and describe your gate; we’ll tell you straight what it will cost.
We Also Serve Cities Near Firestone
Our gate installation crew works throughout the surrounding area. We regularly handle projects in Firestone plus Frederick, Fort Lupton, Erie, and Lafayette, which means scheduling for Firestone properties is flexible and we can coordinate multiple quotes in a single drive. If you live in one of those nearby towns and need a gate installed or automated, call the same number: (877) 610-2993.
Serving Firestone, CO - Our Local Coverage Area
We’re based in the Firestone area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Firestone
The hinge post fails because the original footing was too shallow for Firestone’s freeze-thaw cycle and wind loading. A gate sags in the post, not in the middle, and when the post rotates just half a degree, the whole gate goes out of level. We set new deep footings with rebar cages and correct the sag before re-hanging the gate. If your gate has started dragging at the latch, the next step is a post inspection, not a new hinge. Call (877) 610-2993 and we’ll look at it.
Yes, and we do it regularly in Firestone. Many homes built during the 2005-2020 buildout never had power run to the gate line. We handle the trenching, conduit, wire pull, and a dedicated GFCI circuit to the operator, plus the operator itself and all safety devices. We quote the electrical run as a separate line item so you see exactly what that part costs. An automation conversion with a new power run in Firestone typically lands between $3,800 and $6,900, depending on distance and operator choice.
Yes. UL 325 compliant entrapment protection is a code and safety requirement for automatic gate operators, including the gates in Firestone’s HOA communities. Older gates installed before the current standard often lack photocells or monitored safety edges. We install both, and we insist on compliance even if the HOA has not flagged it yet. An automatic gate without entrapment protection is an injury waiting to happen.
We recommend operators with higher torque ratings and heavier-duty gear assemblies for Firestone, specifically for swing gates. In the field, we have had strong results with FAAC and Viking swing gate operators in Firestone’s wind exposure, replacing stripped builder-grade LiftMaster units. The operator matters, but so does the installation: proper post depth, a solid mounting plate, and correct travel limits are what keep an operator alive through multiple Chinook seasons. Hal will tell you which operator fits your gate and your exposure, and he will stand behind it with the 90-Day Done Right Promise.
Because the homes were built at the same time, by the same builder, with the same operator. In post-2000 HOA communities, one spec went into every home on the street. After a single severe wind season, a dozen homes on the same cul-de-sac can show the same stripped gear or sheared arm. That’s a pattern we see in Firestone more than anywhere else on the northern Front Range. It also means we can often schedule neighborhood-level repairs efficiently and quote honestly. If two of your neighbors need the same operator, that’s not a coincidence; it’s the spec. Call (877) 610-2993 and we’ll help sort it out.
Call Gatewood for Firestone Gate Installation
If you need a new gate, automation, or just a straight answer about the gate you already have, call (877) 610-2993. Hal Gatewood or one of his crew will answer. No dispatch queue, no voicemail, no call center. Ask for a free estimate for your Firestone home and we’ll set a time that works for you. We quote in writing, we weld on site, and every job carries the 90-Day Done Right Promise. If it isn’t done right, we make it right. That’s the whole deal.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Firestone and nearby communities since 2001.