Gate Parts & Welding in Eastchester - Made to Measure, Written Price

Fast, Reliable Gate Parts & Welding Across Eastchester

If your swing gate in Eastchester is binding, sagging, or refusing to close square against the post, the problem usually isn’t the motor. It’s the post footing, a hinge that’s been rusting since the Eisenhower administration, or a weld that finally let go after forty winters of frost heave. We’re Gatewood Fence & Gate, and our Gate Parts & Welding crew has been fixing exactly these problems in Eastchester for years, on-site in your driveway, without hauling your gate off to some shop. Call (877) 610-2993 and Hal will tell you straight what’s wrong and what it’ll cost before we touch a thing.

Why Gatewood Fence & Gate Is Eastchester’s Preferred Gate Parts & Welding Company

Hal Gatewood started this business in 2001 because he got tired of seeing gates torn out and replaced when a solid repair would’ve done the job for a quarter of the price. That’s still how we operate in Eastchester. When you call, a live person picks up. Not a voicemail, not a phone tree. You’ll talk to someone who knows the difference between a hinge that needs rebuilding and one that needs replacing. And you’ll see the same face on the job that you’d see if you walked into the shop.

Eastchester homeowners tell us the same thing every week: another company quoted a motor replacement, and we fixed it by re-plumbing the post. A gate sags in the hinge post, not in the middle, and that is where we start. Every job we do in Eastchester carries our 90-Day Done Right Promise in writing. If it’s not done right, we make it right, one call brings Hal back. No runaround.

Scheduling and dispatch for Eastchester work is coordinated from our New York City office, but the crew that shows up lives in Westchester and knows these neighborhoods. We answer 24/7 at (877) 610-2993.

Our Gate Parts & Welding Services in Eastchester

Eastchester’s housing stock puts real demands on a gate repair company. These are 1940s to 1960s colonials and split-levels, many still running their original wrought iron. Concrete footings have shifted over decades. Hinges have rusted from road salt. The village code adds its own pressure. Here’s what we cover.

Hinge Replacement

Original wrought iron hinges on Eastchester’s older gates aren’t something you swap for a $30 zinc-plated hinge from a box store. They’re rebuilt. We heat, hammer, and re-shape the barrel, press in new pins, and re-weld the strap where decades of swing cycles have cracked it. A rebuilt hinge on a 1960s Eastchester gate will outlast a modern replacement that was never sized for the weight. Typical hinge rebuilding in Eastchester runs $180-$320 per hinge, depending on size and rust damage.

Post Replacement

This is the job that separates a real gate repair outfit from a parts-swapper. In Eastchester, a leaning post isn’t just a cosmetic problem. The village requires automatic gates to stay a specific distance from public sidewalks, often under 18 inches. Frost heave pushes a post a half-inch out of plumb, and now your gate’s swing arc clips the sidewalk or refuses to close fully. That’s a code violation waiting for an inspection. We dig out the old footing, set a new concrete base below frost line, plumb and re-anchor the post, and weld a new hinge plate if the old one has wallowed out. Post replacement in Eastchester typically runs $450-$900 including concrete and labor, more if the post is set in masonry that needs cutting back.

Rail Repair

Bottom rails on Eastchester’s older iron gates rot from the inside out. Snow sits on them, road salt splashes up, and the welds at the stile connections rust through. We cut out the bad section, weld in new steel matched to the original profile, and grind it smooth so the repair disappears under paint. Chasing rail rot with touch-up paint and hope doesn’t work. A typical rail repair runs $220-$480 depending on how far the corrosion has traveled.

Custom Welding

Some Eastchester gates were built to match the house, and that means fiddly ornamental work: scrolls, finials, a monogram medallion, or a latch plate that was never a standard size. We weld on-site with portable MIG and stick equipment, so your gate never leaves the property. Need a custom mounting plate for a Ghost Controls opener on an odd-sized post? We fabricate it in place. Custom welding in Eastchester generally runs $120-$250 per hour plus materials, and most single-repair jobs land in the $180-$400 range.

Trusted Brands We Service in Eastchester

We’re certified on nine major gate operator brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Eastchester we see a lot of LiftMaster swing operators on the older homes and Ghost Controls or Viking units on newer retrofits. We keep common parts stocked for Eastchester calls: drive gears, limit switches, control boards, receiver modules, and hinge bearings. That means we’re not waiting on a warehouse in Ohio when your gate is stuck open at 8pm. If we need a DoorKing or Elite part we don’t have on the truck, we source it same-day from local distributors.

Common Gate Parts & Welding Problems We See in Eastchester Homes

Fix the panel without the post and you’ll fix it twice. That’s the Eastchester story in one line. Here’s what we consistently find:

• Frost heave on 1950s post footings. Eastchester’s mid-century homes were built before anyone thought about pouring footings below Westchester’s frost line. Thirty to forty freeze-thaw cycles a winter slowly tilt posts out of plumb, binding the gate and overloading the operator. The motor isn’t failing. The post moved out from under it.
• Road salt eating iron hardware. Eastchester’s public works crews salt the streets and sidewalks all winter. That salt spray lands on your gate’s hinges, latch bolts, and the exposed ends of low-voltage wire. Original wrought iron will corrode within a single season if it isn’t protected. We see gates that still look decent from the street but have hinges that are paper-thin at the weld.
• Compact lot setbacks causing sidewalk conflicts. Many Eastchester gates sit just feet from a public sidewalk. Post tilts a half-inch, and the gate’s arc now sweeps over the sidewalk edge or won’t latch because the geometry changed. The village notices. Homeowners get a letter. Then they call us.
• Operators burning out from arc changes. A gate weighs a lot more than the motor thinks it does when the swing arc changes by even a half-inch. The motor works harder, pulls more amps, and dies young. Homeowners blame the motor. We re-plumb the post instead.

Pricing for Gate Parts & Welding in Eastchester, NY

We Also Serve Cities Near Eastchester

Our Gate Parts & Welding in Eastchester service area reaches Tuckahoe, Wykagyl, Bronxville, and Scarsdale. We’re familiar with the setback rules and lot conditions in each, and the same crew that works Eastchester handles those calls too. No subcontractors, no strangers. Same truck, same tools, same 90-Day promise.

FAQs - Gate Parts & Welding in Eastchester

Why does my Eastchester swing gate keep burning out its operator every winter?

Because the hinge post has moved. Frost heave pushes Eastchester’s shallow 1950s concrete footings out of plumb, and the gate’s swing arc changes just enough to overload the drive motor. Fix the footing and the next motor will last. Call (877) 610-2993 and we’ll check the post before anyone sells you another operator.

Can you weld original wrought iron hinges on a 1960s Eastchester gate, or do I need full replacement?

We can rebuild original wrought iron hinges in most cases. We heat and re-shape the barrel, press in new pins, and re-weld the strap to the post plate. Full replacement is only necessary when rust has reduced the hinge body to flakes. We’ll show you the hinge and explain why it can or can’t be saved before any work starts.

How close to the sidewalk can my swing gate legally operate in Eastchester?

Eastchester’s village code requires automatic gates to maintain a specific setback from public sidewalks, often under 18 inches. That means a half-inch of post tilt can put your gate out of compliance. If your gate’s arc now sweeps over the sidewalk edge or the gate won’t latch square, get it checked before the village does.

Does Eastchester’s road salt really affect my slide gate rollers?

Yes. Salt spray kicks up from plowed streets and sidewalks and settles on the roller track and bearings. Unprotected steel rollers rust, seize, and then grind flat spots on the track. We replace rollers with sealed-bearing units and treat the track for salt exposure. A $220 roller replacement beats a $600 track rebuild any winter.

Can you add a solar gate opener to a driveway in Eastchester?

We can. Eastchester lots are compact but some driveways sit far enough from the house that running conduit gets expensive or messy. A solar-charged Ghost Controls or Viking operator with a battery bank handles that cleanly. We’ll come out, measure the gate, and give you a written price for the panel, operator, and install before any work begins. Call (877) 610-2993 for a free measure.

Call Gatewood Fence & Gate for Gate Parts & Welding in Eastchester

Show me the gate closing on its own and I’ll show you where it’s failing. That’s Hal’s rule, and it applies to every Eastchester gate we look at. If your gate sags, scrapes, or won’t latch, call (877) 610-2993. A live person answers, day or night. We’ll schedule a visit to Eastchester, put eyes on the post and hinges, and give you a free estimate. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.

Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Eastchester, NY with on-site gate repair and welding since 2001.