Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Dunwoody
We handle gate parts and welding in Dunwoody the way it should be handled: on site, at your gate, with the job done right the first time. If your gate post has heaved in the red clay or a hinge is binding so hard the operator is burning out, we’ll come to you, look at what’s actually wrong, and fix it rather than selling you a gate you don’t need. Our Gate Parts & Welding team works regular hours and emergency calls across 30346, with crews who know Dunwoody’s HOA communities and office-park entries from years of being on the ground. Call (877) 610-2993 any time and you’ll get a live person on the line.
Key Takeaways
– Most gate failures in Dunwoody start at the hinge post or the track, not in the gate panel itself
– We weld on site in your driveway or at your community entrance; the gate never leaves
– 90-Day Done Right Promise stamped in writing on every job, no fine print
– Upfront pricing agreed before work starts; $40 off any repair over $200 for Dunwoody homeowners
Why Gatewood Fence & Gate Is Dunwoody’s Preferred Gate Parts & Welding Company
Gatewood Fence & Gate has been owner-operated since 2001, and Hal Gatewood’s name is on the shop and on every invoice. That means when you call about a hinge replacement in Dunwoody, you’re not talking to a dispatcher three states away. You’re talking to the person who will be there himself, or to someone on his crew who knows the job and answers to him. Our published address and license number are there for anyone to look up, because being easy to verify is part of the point.
Dunwoody is different from most of the north Atlanta suburbs, and the work here shows it. The Gate Parts & Welding in Dunwoody jobs we take tend to fall into two buckets: aging HOA community entrance gates that haven’t seen real maintenance in decades, and commercial security gates along the Perimeter Center corridor that have to work every single day. The HOA jobs especially come with layers most other cities don’t have. Board sign-off. Shared budgets. Gates that were installed when the neighborhood was platted in the 1970s and have been patched, not fixed, ever since.
Every job carries our 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. That’s not a guarantee we hedge on. It’s the whole reason the work holds up in Dunwoody’s red-clay soil.
Our Gate Parts & Welding Services in Dunwoody
Hinge Replacement
When a swing gate starts sagging or binding in Dunwoody, the problem is almost never in the middle of the gate. It’s in the hinge post. We see it constantly in older HOA communities off Mount Vernon Road and around the 1970s and 1980s subdivisions: the post has heaved in the expanding red clay, the hinges have bent or sheared, and the gate is hanging off the operator. We cut out the old hinge, weld in a new one sized for the gate’s actual weight, and set the post before remounting the panel. Most hinge replacements at a Dunwoody single-family gate run $180 to $420, and HOA entrance gates with heavier posts typically run $450 to $900 depending on the post condition.
Post Replacement
Fix the panel without fixing the post and you’ll fix it twice. That’s especially true in Dunwoody, where the expansive clay soil shifts with every wet-dry cycle through the year and slowly heaves posts out of plumb. We re-plumb the post footing, reinforce the pilaster when the brick or stone face has cracked, and weld or re-anchor the gate back to it. A typical post replacement on a Dunwoody residential driveway gate runs $350 to $800; HOA entrance posts on brick pilasters run higher, generally $700 to $1,400, because the pilaster often needs re-plumbing or reinforcement before a new operator can be properly anchored.
Rail Repair
Older slide-gate track channels on 1980s-era commercial entries along Ashford Dunwoody take a beating from Atlanta’s periodic ice storms. The channel freezes, the gate runs against it, and the rail warps until the rollers jam. We straighten or replace the rail, weld in new sections where the metal has cracked, and re-set the rollers so the gate runs square again. Rail repair on a Dunwoody office-park gate usually runs $250 to $650 depending on the length and how much rail has to be sectioned out. If the rollers themselves are shot, we replace them on the same visit.
Custom Welding
A lot of Dunwoody’s ornamental iron work was built in the 1970s and early 1980s, and the fabricators who made it are long gone. When a scroll cracks or a picket breaks loose from the frame, we weld it on site, matching the existing profile as closely as the original permits. We’ve done this work on community entrance gates off Chamblee Dunwoody Road, on driveway gates in Mount Vernon-area subdivisions, and on commercial gates serving the office parks around I-285. Custom welding on a Dunwoody ornamental gate typically runs $150 to $500 depending on the extent of the repair and the complexity of the ironwork.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Dunwoody
We service the brands Dunwoody’s older communities and commercial properties actually run: DoorKing, Viking, Ghost Controls, and Elite, among others. If your 1980s-era community gate is controlled by a DoorKing operator that hasn’t been manufactured in years, we can still source parts or plan a control board swap that keeps the mechanical side working. For newer installations, we stock common Viking and Ghost Controls components locally, which means a repair on a Dunwoody driveway gate often happens the same day we come out. On HOA entrance gates, turnaround depends on board sign-off, but the parts are usually on hand when the approval comes through.
Common Gate Parts & Welding Problems We See in Dunwoody Homes
- Red-clay heave on hinge posts and pilasters. Dunwoody’s expansive clay soil shifts dramatically through wet and dry seasons, and over thirty or forty years that movement pulls gate posts out of plumb. The result is a swing gate that binds, sags, and eventually burns out the operator trying to move it.
- Frozen and cracked slide-gate track channels. The ice storms that hit the Atlanta metro every few years freeze older track channels on commercial entries along Ashford Dunwoody, leaving rails warped and rollers jammed when the thaw comes.
- Obsolete telephone-entry and loop-detector systems. Many Dunwoody HOA communities still run original 1980s-era entry systems wired into operators that haven’t been built in decades. When the board finally authorizes a fix, the whole control board usually has to be swapped just to restore basic function.
- Pilaster cracks behind brick or stone facings. The ornamental iron on Dunwoody’s community entrances is often mounted to brick or stone pilasters that have cracked under decades of soil movement. Welding a new hinge to a failing pilaster doesn’t help; the pilaster itself has to be reinforced first.
Pricing for Gate Parts & Welding in Dunwoody, GA
Here’s what we quote on this side of Dunwoody. Hinge replacement: $180 to $420 for single-family gates, $450 to $900 for HOA entrances. Post replacement: $350 to $800 residential, $700 to $1,400 when pilaster work is involved. Rail repair: $250 to $650. Custom welding: $150 to $500. These are the ranges we give over the phone, and the number we quote is the number you pay. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Every price is agreed before work starts, in writing. Call (877) 610-2993 for an exact quote on your gate; estimates are free.
We Also Serve Cities Near Dunwoody
Our crews cover Dunwoody and the surrounding north Atlanta cities daily. If you’re in Sandy Springs, Chamblee, Doraville, or Brookhaven, the same team handles gate parts and welding there too, same 90-Day Done Right Promise, same live person on the phone. Whether you’re in Dunwoody proper or just outside the 30346 line, the job gets scheduled with someone who knows the local soil, the local HOA boards, and the local gate hardware.
Serving Dunwoody, GA - Our Local Coverage Area
We’re based in the Dunwoody area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Dunwoody
Dunwoody’s red clay expands and contracts with every wet-dry cycle, and over three or four decades that movement heaves hinge posts out of plumb. The gate panel isn’t the problem; the post supporting it is. We see it most often in the older HOA communities platted in the 1970s, where the original steel posts were never set deep enough for the soil conditions. Call (877) 610-2993 and we’ll tell you over the phone whether your gate needs a post or just a hinge; the estimate is free.
Yes. The gate itself has to stay open during the rail replacement, but the driveway doesn’t close. We section out the warped or cracked rail, weld in the new channel, and keep at least one lane open for traffic throughout. On Ashford Dunwoody entries with two lanes, we can do the job while the morning rush comes and goes. Call (877) 610-2993 and we’ll walk you through the timing.
We replace the control board and any obsolete wiring, then see if the mechanical side is worth keeping. In most Dunwoody HOA communities running 1980s-era DoorKing or Elite operators, the motor and gearbox still have life in them; it’s the board that has to be swapped. That’s a board-level repair, typically cheaper than a full operator replacement, but it requires HOA board sign-off before we start. Call (877) 610-2993 for a written quote you can take to your board.
Yes, and we check the pilaster before we weld to it. Brick and stone pilasters on Dunwoody’s older community entrances often have hairline cracks from the same red-clay movement that shifts the gate. We weld the gate to the pilaster only after the pilaster is reinforced if it needs to be. The work is done on site, with the gate kept on its hinges where practical. Call (877) 610-2993 to schedule a look.
We brace the gate, dig and re-set the post in stages, and keep the driveway passable throughout. On shared Dunwoody driveways where the gate serves two homes, we’ll schedule the work so at least one vehicle can get in and out the whole time. It takes a little longer, but it means nobody is locked out of their own driveway. Call (877) 610-2993 and we’ll work out a plan for your specific entrance.
Call Gatewood Fence & Gate for Gate Parts & Welding in Dunwoody
If your Dunwoody gate is sagging, binding, or stuck, call (877) 610-2993. You’ll get a live person, an honest opinion, and a price that’s quoted before work starts and doesn’t change at the door. Hal’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Dunwoody since 2001.