Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Camas
Gate parts and welding in Camas is different work than it is ten miles west. The wind coming through the Columbia River Gorge loads gates sideways for days at a time, and hillside lots settle posts out of plumb in ways flat-ground gates never see. If your gate is sagging, dragging, rattling in the wind, or the hinges are tearing out of the post, we can usually have it repaired same week, often same day. Hal Gatewood has been doing this since 2001, and the person who answers your call is the person who stands behind the work. Reach us at (877) 610-2993.
Why Gatewood Fence & Gate Is Camas’s Preferred Gate Parts & Welding Company
We’re the Gate Parts & Welding shop that repairs before we replace. That matters in Camas, because a gate on a Prune Hill slope or an east-facing lot off Lake Road can fail in ways a flat-lot gate in Vancouver simply does not. We weld on site, in your driveway, so the gate never leaves your property. If a hinge post has settled, we set a new one deeper and true. If a weld has cracked, we grind it, re-weld it, and gusset it so the same failure doesn’t come back in the next east-wind event.
Local reputation builds slowly and dies fast. Ours is built on showing up when we say we will, quoting a price before any work starts, and backing every repair with the 90-Day Done Right Promise in writing. Every call to Camas gets answered by a live person, 24/7. Not a voicemail. Not a call center three states away. Hal’s name is on the shop, the address is published, and the license number is there for anyone to look up.
Our Gate Parts & Welding Services in Camas
Here is the work we do most often for Camas homeowners, and what it typically involves on the ground here.
Hinge Replacement
Hinge replacement in Camas is rarely just swapping hardware. On Prune Hill and other hillside subdivisions, a gate that sags usually has a hinge leaf pulling out of a post that has settled or a frame that has racked from Gorge wind. We install heavy-gauge hinges with through-bolts where the post can take them, or we weld barrel hinges directly to steel frames. On wood gates, we use longer hardware and reinforce the hinge stile so the screws are not doing all the work. Same-day hinge work is common, and the job is quoted before we start.
Post Replacement
A gate sags in the hinge post, not in the middle. That’s where we start on every Camas post replacement. Hillside freeze-thaw cycles soften the soil around posts on sloped lots, and a post that was set 20 years ago in wet clay has often settled a half inch out of plumb. We dig the old footing out, set a new steel post in deeper concrete with added gusset plates when wind load calls for it, and hang the gate true. On shared driveways and rights of way, we keep the work tight to the post so vehicle access stays open while we work.
Rail Repair
Steel gate rails in Camas crack. The repeated lateral stress from Gorge east winds flexes the frame where the top rail meets the hinge stile, and a crack that starts as a hairline turns into a gate that folds. We cut the cracked section out, sleeve and weld in new material, and add a gusset plate at the stress point. On aluminum gates, we clean, prep, and weld with the correct filler so the repair does not corrode from the inside out through wet winters.
Custom Welding
When a gate frame is too far gone for a patch, we build a new one to fit the existing opening and operator. Custom welding in Camas often means matching an ornamental iron pattern on a 90s-era hillside home, or reinforcing a sliding gate on a tight lot where a swing gate was never going to fit. We measure, fabricate, and weld on site. The finished frame is primed and painted before it’s hung, and the operator is recalibrated to the new gate weight. We also handle smaller custom work: drop rods, cane bolts, latch plates, and hinges for odd-width openings.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Camas
Our shop works on nine major gate brands, and for Camas customers that matters because we stock the common wear parts locally. We regularly maintain and repair operators from Linear, Viking, and Ghost Controls, along with FAAC, BFT, DoorKing, and the others we carry. If your automatic gate is off its travel limits, stripping, or refusing to close against the wind, we diagnose the operator and the mechanical gate as one system. Most parts for these brands are on the truck or one day out, which means we are rarely waiting on a shipment to finish a Camas job.
Common Gate Parts & Welding Problems We See in Camas Homes
- Gorge wind racking on east-facing gates. A single bad east-wind week in November can strip hinge screws from softwood posts, shear hinge bolts on steel frames, and knock operators out of travel-limit calibration all at once. This cluster failure is a Camas signature, and flat-terrain Clark County gates rarely see it.
- Hillside post settlement and gate drag. Sloped lots on the Prune Hill corridor settle posts over time, which pulls the gate out of plumb and drags on the latch side. The fix is a new, deeper footing and re-hanging the gate true, not shimming the hinges and hoping.
- Wet-winter wood rot at post bases. Older downtown Camas homes and cedar privacy-fence gates on hillsides rot at the post base from moisture that never fully dries between rains. Wind-loading accelerates hinge tear-out once the wood softens.
- Sliding gate hardware failures on tight lots. Where a swing gate will not fit, sliding gates take the full sideways force of the wind on their rollers and rack. We see bent drop rods, stripped rack mount bolts, and rollers that have chewed through their track.
Pricing for Gate Parts & Welding in Camas, WA
We Also Serve Cities Near Camas
We regularly drive to Washougal, Mill Plain, Orchards, and Barberton for the same gate parts and welding work we do in Camas. If you are just outside town and wondering whether we cover your road, call us. We will tell you straight. And yes, we serve all of Camas, from the Prune Hill ridgeline down to the flats by the paper mill.
Serving Camas, WA - Our Local Coverage Area
We’re based in the Camas area and offer Gate Installation in Camas, and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Camas
Why does my Camas gate keep sagging after the hinge post was replaced once?
Because the post footing was not set deep enough for Camas soil on a slope, or the post was installed without accounting for Gorge wind load. We see this constantly. Freeze-thaw softens hillside soil, wind racks the frame, and a post that was set shallow works loose within a season or two. We set replacement posts deeper, add gusset plates where the wind calls for it, and hang the gate so it closes without bind. Call (877) 610-2993 and we will tell you what the last repair missed.
Do your welded repairs hold up against the east wind on Prune Hill?
Yes, when the repair is designed for the load. On a shared driveway near Prune Hill, we rebuilt a wind-racked steel slide gate after the Gorge winds stripped the hinge post anchors and threw the gate off its rollers. We installed a new hinge post with a deeper footing, re-aligned the rack and pinion drive, and added a sacrificial shear bolt so the post survives the next east-wind event instead of the gate frame. That is the difference between a weld that holds and a weld that fails. We design for the wind, not just the repair.
Can you replace just the drop rod and latch on my sliding gate without changing the gate operator?
Yes. Drop rods, cane bolts, and latches are independent of the operator, and we replace them all the time without touching the motor. If the wind bent your drop rod or the latch no longer seats, we can fabricate and install a new one same day in most Camas neighborhoods. The operator stays set; only the mechanical hardware changes.
What is the minimum clearance you need to work on a gate between my house and the neighbor’s fence?
About 18 to 24 inches on the hinge side, and we can work with less if we can reach the hinges from the front. Tight side-yard gates on older downtown Camas lots are part of the job. We bring compact welders and work close quarters without tearing out the neighbor’s fence or your house wall.
Do you keep pedestrian access open while welding a new gate frame?
Yes. On shared driveways and any gate that serves foot traffic, we keep the pedestrian path open while we weld. If we are pulling the gate off its hinges for a full rebuild, we set a temporary panel or leave a clear walkway so your family and neighbors are not locked out. A gate repair should not shut down your driveway any longer than it has to, and for us it does not.
Contact Gatewood Fence & Gate for Gate Parts & Welding in Camas
If your gate is sagging, rattling in the east wind, or the hinges are tearing out of the post, call us at (877) 610-2993. We answer live, 24/7. The estimate is free, the price is written before any work starts, and the 90-Day Done Right Promise means one call brings Hal back. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Camas and Clark County since 2001.