Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Burke
Gate parts and welding in Burke, VA usually means one of three things: a post that has shifted out of plumb, a hinge that finally gave out on a 35-year-old gate, or a homeowner who wants Gate Installation - Burke automation added to a gate that was built manual. Most jobs run $180 to $650 and we handle them the same week. Hal Gatewood has been fixing gates since 2001, and his crew knows Burke’s neighborhoods: the sprawling sections of Burke Centre, the colonials off Burke Lake Road, the townhome clusters near the VRE station. If your gate drags, sags, won’t latch, or the operator just stops mid-swing, call (877) 610-2993 and a live person answers. Not a voicemail. Not a call center.
Why Gatewood Fence & Gate Is Burke’s Preferred Gate Parts & Welding Company
We show up in the window we promise. That matters in Burke, where a broken gate is also an HOA violation waiting for a letter. Homeowners here have dealt with national companies that quote one number on the phone and a different one at the door. Hal doesn’t work that way. The price is quoted and agreed before any work starts, in writing, and the 90-Day Done Right Promise says plainly: if it’s not right, we come back and make it right. No hedge language, no fine print.
Our Gate Parts & Welding crew carries profile-matched aluminum rail and iron-look pickets on the truck because we know Burke Centre’s covenants require it. We’ve worked clusters off Oak Green Drive, sections near Lake Braddock, and the older townhome pods where original late-80s gates are all hitting end of life at the same time. Hal’s name is on the shop and on every invoice. You can drive to the shop and look him in the eye if you want to. That’s the oldest accountability there is.
Burke homeowners call us because we weld on site. The gate stays in your driveway. We don’t haul it off, we don’t swap parts that don’t need swapping, and we don’t sell you a replacement when a repair is the right call. That fix-first approach matters in Burke more than most places, because the ARB paperwork and covenant compliance add a layer of friction that a sloppy company just skips, leaving you to deal with the violation notice.
Our Gate Parts & Welding Services in Burke
Hinge Replacement
Hinge replacement in Burke is rarely just a hinge swap. On the original ornamental aluminum gates in Burke Centre’s older sections, the lower hinge post has usually heeled out of its 1980s footing, which means a new hinge on the old post lasts about one freeze-thaw season before it sags again. We check the post first. Runs $120 to $280 per hinge depending on profile matching and whether the post needs resetting.
Post Replacement
This is the big one in Burke. The Piedmont clay under Fairfax County heaves in winter and shrinks in summer, and posts set in the original builders’ concrete footings rack out of plumb year after year. We cut the old post at the base, weld a new one at proper depth with a footing that actually reaches below the frost line, and rehang the gate so it swings true. A typical post replacement in Burke runs $350 to $750 including concrete and profile-matched steel or aluminum. If the post is racked, new hinges alone won’t hold. That’s not opinion; that’s what we see every spring on gates from Burke Lake Road up to 22015.
Rail Repair
Aluminum rail corrodes at the weld joints, especially where road salt from Burke’s winter treatment program sits against the lower rail. We cut out the bad section and weld in matching profile aluminum, then re-finish so the repair doesn’t look like a patch. Rail repairs run $90 to $200 per joint. In Burke Centre clusters with iron-look aluminum covenants, this is the difference between passing ARB inspection and getting flagged.
Custom Welding
When the exact profile for a 1987 Burke Centre gate isn’t sold anywhere anymore, we fabricate it. We’ve cut and re-welded matching rail sections, rehung sagging pickets, and built adapters for operators on gates that were never meant to carry one. Custom welding jobs in Burke run $200 to $600 depending on the complexity, and we show you what we’re doing before sparks fly. No mystery work.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Burke
We’re certified to service nine major gate brands, and the ones we see most on Burke properties are LiftMaster, Viking, and DoorKing. If your builder put in a Ghost Controls or Elite board, we handle those too. We stock common Gate Access Control in Burke replacement boards, safety edges, photocells, and remotes for Burke homeowners, which cuts the wait down to days instead of weeks. You don’t need a whole new operator because a board failed. You need a board, which costs a fraction of what some companies quote.
Common Gate Parts & Welding Problems We See in Burke Homes
- Builder-grade operators dying early. Developers in Burke’s newer sections install entry-level motors that were never meant to fight clay-driven post movement. After two or three winters, the gate binds against the post, the motor overdraws, and the board fries. A sturdier operator plus a properly set post fixes what the builder’s choice created.
- Retrofitting automation onto manual gates, done wrong. We see this constantly: a homeowner wants an opener added to a gate built manual, and the previous quote didn’t mention conduit runs. Exposed wire fails Fairfax County inspection, and rain trips the safety photocells. Real automation requires a conduit run and proper power. We plan for it, and we handle the run.
- Post footings that were too shallow from day one. Original Burke Centre construction from the late 1970s and early 1990s used footings that don’t reach below the expansive clay line. The result is a gate post that racks out of plumb a little more each year until the gate drags a 2-inch groove in the concrete and the latch stops lining up.
- ARB profile mismatches. A homeowner replaces a damaged panel with a generic big-box aluminum panel, and the Burke Centre Architectural Review Board flags it because the profile doesn’t match the cluster’s approved iron-look design. The gate has to come back down. We know this workflow and pre-match the profile before we weld anything.
Pricing for Gate Parts & Welding in Burke, VA
| Service | Typical Range in Burke |
|---|---|
| Hinge replacement (per hinge) | $120 - $280 |
| Post replacement (with new footing) | $350 - $750 |
| Rail repair (per joint) | $90 - $200 |
| Custom welding job | $200 - $600 |
| Operator board replacement | $180 - $450 |
These are real numbers for Burke’s market. What moves a job within the range: whether the post needs resetting, whether the profile has to be fabricated, and whether ARB paperwork is involved. Every job gets a written quote before work starts. You know the number, you agree to the number, and that’s the number on the invoice. We offer $40 off any repair over $200, a permanent 10% discount for seniors and veterans, and no trip charge inside the county. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Burke
If you’re outside Burke proper, we also run crews to Kings Park West, Fairfax, Springfield, and Merrifield. The same crew, the same 90-Day Done Right Promise, the same live-answer phone. Gate Parts & Welding in Burke is our core service area, but we’re on the road all week along Braddock Road and the Fairfax County Parkway.
Serving Burke, VA - Our Local Coverage Area
We’re based in the Burke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Burke
Yes. Burke Centre’s Architectural Review Board must sign off on any gate modification that changes profile, material, or color. Hinge replacement that matches the existing hardware typically does not require new approval, but post replacement often does because the new post or panel must match the cluster’s approved iron-look aluminum. We walk you through the paperwork and pre-match the profile so the ARB has nothing to flag. Call (877) 610-2993 and we’ll tell you exactly what your cluster requires before we touch a torch.
Because the hinge was never the real problem. The lower hinge post is racking in its original 1980s footing, pushed out of plumb by Burke’s expansive clay. Replace the hinge without resetting the post and the gate sags again within a year. We start at the post, set it in a footing that reaches below the frost line, and then hang the hinges. That sequence is the only one that holds. Call (877) 610-2993 to have us look at the post before you spend another dollar on hinges.
Yes, and it usually requires a conduit run for power and safety edges. Builders rarely leave an empty conduit under the driveway, so the wire has to go in properly, which means cutting a chase, laying conduit, and patching. We handle the full Burke Gate Motor & Opener retrofit: weld the operator mount, run the power, install the safety photocells and edges, and program the opener, usually a LiftMaster or DoorKing. Budget $600 to $1,400 depending on the gate and the run distance. Call (877) 610-2993 for a free measurement and written price.
Only if the new panel matches the profile approved for your cluster or section. Burke Centre’s older covenants specify a wrought-iron-look aluminum profile, and a generic big-box panel will not pass. We stock and source profile-matched material, so the welded panel looks like it belongs on the gate. We also handle the paperwork. Most ARB applications for a profile-matched repair clear review without issue. Call (877) 610-2993 if you want us to verify your cluster’s requirement first.
Sometimes it is, sometimes it isn’t. If the gate binds on a post that has shifted, the operator hits resistance and reverses as a safety response. That’s a post alignment problem, and welding alone won’t fix it. If the gate swings free but still reverses, the issue is usually a photocell alignment, a safety edge, or a board going bad. We diagnose it on site, show you the exact cause, and quote the fix before we do anything. Call (877) 610-2993 and we’ll get it sorted, usually the same week.
Key Takeaways for Burke Homeowners
- Post problems cause most gate failures in Burke, not hinge or latch problems. Fix the post first.
- ARB approval is required for most gate modifications in Burke Centre. We handle it.
- Profile-matched welding passes covenant inspection. Generic panels do not.
- Pricing is quoted and agreed before work starts. No surprises at the door.
- Hal has been owner-operated since 2001. His name is on the shop and every invoice.
If your gate is dragging, sagging, or just won’t close, call (877) 610-2993. A live person answers, 24/7. We’ll give you a straight answer, a written price, and a time we’ll be there. We’ve fixed gates in Burke Centre, off Burke Lake Road, and through every zip from 22009 to 22015. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Burke since 2001.