Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Burke
A new driveway gate in Burke runs roughly $2,800 to $7,500 installed, and a swing gate operator with power run adds $1,900 to $4,200 on top. Most Burke installs take one to two days once materials are on hand, though Burke Centre jobs with Architectural Review Board approval pending can stretch the schedule. If you’re in zip 22009 or 22015 and your gate is sagging, dragging, or still manual, Gate Repair - Burke is what you need-call (877) 610-2993 and Hal will tell you straight what it’ll cost before anything gets ordered.
We work Burke hard because Burke is where the HOA rulebook meets the clay soil, and both of them fight a sloppy gate install. Our Gate Installation crew has reset more racked posts and matched more ARB profiles in Burke Centre than we can count. When you call, a live person answers. Not a menu. Not a voicemail.
Why Gatewood Fence & Gate Is Burke’s Preferred Gate Installation Company
Hal Gatewood opened this shop in 2001 and put his name on it. That matters in a place like Burke, where the person who quotes the job is the same person who shows up with the welder. We don’t sub out the work and we don’t send a salesman who’s never touched a hinge. Hal is on the phone, on the site, and on the invoice.
Burke homeowners call us for one reason more than any other: a national outfit already came out, quoted one price, and tried to charge another at the door. That doesn’t happen with us. The price we agree on before we start is the price on the bill when we finish, and it’s in writing. Every job carries the 90-Day Done Right Promise, stamped plainly, not buried. One call brings us back.
We answer the phone 24 hours a day, seven days a week. A live person. If a gate drops off its track on a Sunday night in Burke Centre, you get Hal or someone from his crew, not a recorded voice telling you to call back Monday.
Our Gate Installation in Burke Services
We install and automate gates all over Burke, from the colonials off Burke Lake Road to the townhome clusters near the VRE station. Here’s what we handle most:
Driveway Gate
Most Burke driveways in the older sections were built for manual gates, which means no power, no conduit, and posts set in the original builders’ footings. We install the gate and the operator, run the power properly, and set the posts deep enough that Piedmont clay won’t shove them out of plumb in two winters. A driveway gate in Burke typically runs $3,200 to $7,500 installed, depending on width and operator type.
Swing Gate
Swing gates are the most common style in Burke, and the most common failure is a hinge post that’s been heaving for thirty years. We don’t bolt a new panel onto a leaning post and call it Gate Parts & Welding - Burke done. The post gets reset first, then the gate hangs level and closes clean. If you’re going from manual to automatic, we spec an operator with enough duty cycle for daily use, not a bargain unit that burns out by the second winter.
Double Gate
Double driveway gates in Burke Centre’s larger sections usually hold two full panels, often with the original wrought-iron-look aluminum from the late 1970s or early 1980s. Replacing one panel often means matching the profile of the other, and Burke Centre’s covenants don’t give you much wiggle room on that. We source profile-matched material so the ARB signs off the first time. Double gate installs generally run $4,500 to $7,500 before the operator.
Pedestrian Gate
Smaller walk gates don’t get the same attention as driveway gates, but they fail just as often when the post shifts and the latch stops lining up. We install and weld pedestrian gates throughout Burke’s townhome sections, including matching styles required by the cluster’s covenants. Expect $900 to $2,200 for a typical pedestrian gate, post reset and latch work included.
Trusted Brands We Service in Burke
We’re certified on nine major gate brands, and the ones that show up most on Burke driveways are FAAC, BFT, and Linear. We stock common parts for these locally, so a Burke repair doesn’t wait on a warehouse three states away. LiftMaster operators are everywhere in Burke Centre too, especially on homes where a builder or a previous owner automated the gate years ago. When we install, we recommend the brand that fits the gate and the duty cycle, not the brand we happen to have left over on the truck.
Common Gate Installation Problems We See in Burke Homes
- Racked hinge posts on 30-to-45-year-old gates. The original ornamental aluminum and wood gates in Burke’s master-planned sections are decades past their expected service life. Posts set in the original concrete footings have shifted with every freeze-thaw cycle, and no new latch or hinge will hold until the post is reset.
- Operator installed without fixing the gate first. A sagging 1980s gate will bind and strip the operator’s gears within a season or two. We fix the gate before we hang an operator on it, because fixing it afterward costs more.
- Generic aluminum panels that fail ARB review. In Burke Centre’s older clusters, the covenants are specific about profile, material, and color. A big-box panel that looks “close enough” gets flagged, and the homeowner eats a second install plus new materials.
- Dead operators mid-winter from shallow conduit. Burke’s clay soil shifts enough through freeze-thaw that a shallow, undersized conduit run cracks and shorts. We run schedule-80 conduit at proper depth, or we tell you honestly if a different power path makes more sense.
One story from this spring. Our crew was on a double driveway gate in Burke Centre, an original from the early 1980s. The builder-grade hinges had sagged over 35 years, and the posts were racked enough that the gate dragged on the concrete. We reset both posts in new footings, corrected the sag, hung a LiftMaster swing operator, and ran fresh conduit for the operator and a safety photocell. The ARB’s final walk-through passed without a note. That’s the job done the way it should’ve been done the first time.
Pricing for Gate Installation in Burke, VA
Here’s what Burke homeowners can expect to pay, based on the work we’ve done from the Fairfax County line up through Burke Centre and down toward the Springfield border.
| Service | Typical Range in Burke |
|---|---|
| Pedestrian gate install (material + labor) | $900 - $2,200 |
| Single swing gate install | $2,800 - $5,500 |
| Double driveway gate install | $4,500 - $7,500 |
| Swing gate operator + power run | $1,900 - $4,200 |
| Sliding gate install (track or cantilever) | $3,500 - $8,500 |
| Post reset (per post, incl. concrete) | $400 - $900 |
We quote every Burke job before work starts, and that number doesn’t move. No trip charge inside the county. $40 off any repair over $200, and seniors and veterans get 10% off permanently. You’ll also get the 90-Day Done Right Promise in writing on every job. Call (877) 610-2993 for an exact quote, it’s free and it comes from a person who will be the one doing the work.
We Also Serve Cities Near Burke
If you’re just outside Burke, we work the surrounding communities too: Kings Park West, Fairfax, Springfield, and Merrifield. Same crew, same 90-Day Done Right Promise, same live person on the phone. Wherever you are in the area, Burke is home turf for us, so you’re not getting a stranger.
Serving Burke, VA - Our Local Coverage Area
We’re based in the Burke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Burke
Yes. In most Burke Centre clusters, adding an automatic opener counts as a modification that requires Burke Gate Access Control Architectural Review Board approval, and the covenants typically require the work to match the cluster’s approved equipment and finishes. We know the Burke Centre ARB workflow and can help you assemble the application, and we’ll spec equipment that fits the community’s standards so you’re not standing in front of the board twice. Call (877) 610-2993 and we’ll talk you through what your cluster’s rules actually say.
In nearly every case we see in Burke, the dragging is a hinge-post problem, not a panel problem. The original posts were set in the builders’ concrete footings, and Piedmont clay heaves through freeze-thaw cycles until the post inches out of plumb. The gate panel settles, the hinge bind, and it drags. Fix the post first and the gate hangs right. Put a new panel on the old post and you’ll fix it twice.
Usually not, and we’ll tell you that before you spend the money. Burke Centre’s older sections have mature tree canopy that shades a lot of driveway space, and a solar opener that gets three hours of weak sun a day will leave you with a dead battery and a gate that won’t move. We’ll evaluate your specific lot. On most Burke properties, running power is the honest answer, even though it costs more upfront.
We set the swing on an uphill plane so gravity helps keep the gate closed, and we adjust the hinge placement so the panel doesn’t drag as it arcs downhill. Some townhome driveways in Burke need a modified post set or an inline stop to keep the gate from swinging into the street. We handle the slope on site, and the set is level before the operator ever gets bolted on. Call (877) 610-2993 and we’ll come measure, free.
If you want the gate to open automatically when a car pulls up, yes, you need a loop detector cut into the driveway. If you only want a remote or keypad, it’s optional. On Burke driveways where the first few feet are asphalt over clay, we cut the loop carefully and seal it against water intrusion, because a cracked seal lets moisture in and the loop stops reading in the first hard freeze. We’ll lay out the options and the cost before we start, not after.
Contact Gatewood Fence & Gate for Gate Installation in Burke
If you’re in Burke and your gate is dragging, sagging, manual, or just ugly, call Hal at (877) 610-2993. You get a live person, a straight answer, and a written quote that doesn’t move. Free estimates, no trip charge inside the county, and the 90-Day Done Right Promise on every job, in writing. The name is on the shop. The shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate.