Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Banning
Gate parts and welding in Banning comes down to one thing most people don’t think about until a hinge snaps: the San Gorgonio Pass wind loads your gate endures every single day. We stock and weld the parts that actually hold up here. A typical hinge replacement in Banning runs $180-$340, and a cracked post that needs resetting or replacing usually falls between $350 and $750 depending on what the existing footing looks like. If your gate is sagging, scraping the driveway, or the operator just stopped, call (877) 610-2993 and we’ll get eyes on it fast.
Why Gatewood Fence & Gate Is Banning’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and he’s been fixing gates in the Pass long enough to know exactly what the wind does to a hinge over two or three seasons. When we show up in Banning, we’re not guessing at which parts will last. We’re choosing them based on where your gate sits relative to the wind corridor, how old your block pilasters are, and whether the last guy used residential-rated hardware on a gate that needed commercial-duty. That’s the difference between a repair that holds and one you’ll be calling about again next spring.
Homeowners in Banning keep our number because Hal’s name is on the shop, the shop is a real place you can drive to, and the person who answers the phone is a person. A live person, 24 hours a day, not a voicemail or a call center three states away. When you call about a gate that won’t close off San Gorgonio Avenue or over in the older grid streets near downtown, you get a straight answer about when we can be there and what it’ll cost.
Every job we do in Banning gets the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Hal back. No runaround, no arguing about what was said on the phone. The price you’re quoted is the price on the invoice, agreed before any work starts.
Our Gate Parts & Welding Services in Banning
Our Gate Parts & Welding team handles the repair-first work that keeps your existing gate in service. We don’t push replacements when a weld and a hinge will do. Here’s what we do most often in Banning.
Hinge Replacement
Banning wind is relentless on hinges. A wrought iron gate on a block pilaster off Sunset Avenue or Wilson Street can develop hairline cracks in the mortar joints after just a few Santa Ana events. The gate leaf drops, binds on the driveway apron, and the operator starts working twice as hard. We replace hinges with wind-rated units sized for double the lateral load a typical hinge sees, and we through-bolt them into the block or steel post, not just lag them into the face. A hinge replacement in Banning typically runs $180-$340 per hinge depending on the weight of the leaf and whether we’re welding the new barrel to the gate frame.
Post Replacement
This is the one Banning homeowners don’t see coming. The post looks fine from the driveway, but the wind has been working the base in its footing for years. When we pull the post, the concrete’s cracked through and the lag bolts are loose in rotten or shattered block. We dig the old footing, set a new post in a 4-foot-deep concrete pour, and through-bolt the hinge tabs so wind load transfers through the post and into the ground, not into a few screws. Post replacement on a Banning residential gate usually runs $350-$750, more if we need to rebuild a block pilaster rather than just reset the steel.
Rail Repair
Wrought iron rails fail at the mid-rail weld. That’s where wind-induced vibration concentrates flex, and over two or three windy seasons in the Pass, the weld fatigues and snaps. The gate panel ends up hanging by one hinge, racked and twisting. We cut out the failed section, weld in new rail matched to your existing steel profile, and grind it clean before repainting. Rail repair in Banning typically runs $150-$350 per rail. If the frame has racked badly, we may need to square the panel on the truck and re-weld the corner joints while we’re at it.
Custom Welding
Sometimes the fix isn’t a part you can order. A gate built for a different house, a shared driveway with an odd setback, or a frame that’s been modified once already. We weld on-site in your driveway. Custom welding for Banning gate repairs generally runs $120-$250 per hour including setup and cleanup, and we’ll give you a fixed number before we strike the first arc. We’ve rebuilt hinge barrels, extended gate panels, fabricated new bracket assemblies, and converted worn slide gate tracks welded together from bent stock.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Banning
We service and install parts for the operators we see most often on Banning gates: Viking, Linear, Ghost Controls, and DoorKing. We know these machines and we know how they fail in the Pass. Consumer-grade operators that do fine 15 miles west in low-wind neighborhoods burn out their motors fighting the near-daily gusts here. On residential installations in Banning, we regularly upsize to commercial-duty specs because the wind load demands it. We keep common boards, gearbox bits, and safety edges in stock for fast turnaround on Banning calls, and we’re certified to work on all nine major brands we service.
Common Gate Parts & Welding Problems We See in Banning Homes
- Hinge posts cracking at the block pilaster. The wind works the mortar joints until hairline cracks spread through the block. The gate leaf drops, the latch stops lining up, and the operator starts grinding. We reset or replace the post and through-bolt everything.
- Slide gate rollers pitting and flattening. Wind-driven grit off the Pass acts like sandpaper on rollers and track. Once a roller flattens, the gate jumps the track and shears rack and pinion teeth. We replace rollers and inspect the rack for stripped sections on every Banning slide gate call.
- Wrought iron rails snapping at the mid-rail weld. Vibration concentrates flex at the weld joint until fatigue cracks propagate through. By the time you see it, the panel’s hanging and racked. We weld in a new rail section and reinforce the joint.
- Operators burning out early. A motor sized for a light residential gate in a calm neighborhood dies quickly against 40 mph sustained winds, 100-plus days a year. We spec operators for the load, not the gate width, and we add safety edges and photocells so the gate never fights a person.
Pricing for Gate Parts & Welding in Banning, CA
Here’s what Banning homeowners can expect. Hinge replacement runs $180-$340 per hinge. Post replacement sits between $350 and $750 for a typical residential gate, more if the block pilaster itself needs rebuilding. Rail repair lands at $150-$350 per rail. Custom welding is $120-$250 per hour with a fixed quote upfront. Slide gate roller replacement runs $220-$480 depending on the track and rack condition. Everything is quoted and agreed before any work starts, and you get the price in writing. Seniors and veterans get 10% off permanently, any repair over $200 takes $40 off, and if you have a written estimate from another company, we’ll give you a free second opinion. No trip charge inside the county. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Banning
If you’re outside Banning proper, we run the same crew and the same 90-Day Done Right Promise to Beaumont, Cherry Valley, Calimesa, and San Jacinto. The Pass wind doesn’t respect city limits, so neither do we. Whether you’re just over the line or deeper into the corridor, Banning is ground zero for wind-rated gate work, and we treat every nearby stop with the same care as a call down the street from the shop.
Serving Banning, CA - Our Local Coverage Area
We’re based in the Banning area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Banning
Your Banning swing gate hinges should be rated for at least double the lateral load a typical residential hinge carries, because sustained 40 mph winds with gusts over 60-80 mph multiply stress far beyond what a calm-climate hinge ever sees. We use commercial-duty hinge barrels with through-bolted tabs on most Banning repairs, not homeowner-grade hardware. If your hinges have already been replaced once and are failing again, call (877) 610-2993 and we’ll spec the right rating for your gate’s exact exposure.
Yes, we can keep a shared driveway gate working while we replace the hinge post, and we do it often in Banning’s older grid streets where shared driveways and tight rights of way are common. We support the gate leaf on steel stands and braces, pull the failed post, set the new one, and rehang the leaf, all while traffic keeps moving through the same opening. The price is agreed before we start, and the 90-Day Done Right Promise covers the new post and hinges. Call (877) 610-2993 to schedule it.
A Banning gate operator that dies after a year was almost certainly sized for light residential wind exposure, not the sustained Pass winds your gate fights every day. The motor cooks itself trying to hold and move a gate that’s being pushed sideways by 40 mph sustained winds, and the gearbox strips out trying to overcome wind-driven resistance. We upsize operators to commercial-duty specs on Banning residential installs for exactly this reason. If your operator is dead or grinding, call (877) 610-2993 for a free estimate before you buy another one that won’t last.
Welding can fix a racked Banning gate in most cases, and it’s usually far cheaper than replacing the whole panel. We square the frame, weld the corner joints and mid-rail, and reinforce the weak points where wind flex concentrated. If the post has cracked at the footing, the gate may still need post work, but the frame itself is almost always salvageable. Call (877) 610-2993 and we’ll tell you straight what’s fixable and what isn’t before any work is quoted.
In Banning, most residential swing-to-slide gate conversions don’t require a separate building permit beyond standard gate and operator work, but setbacks and right-of-way clearance matter, especially on the older grid streets near downtown. We check the site, measure the slide path, and handle the work inside Banning’s requirements. If a permit does come up, we’ll flag it before we quote. For a free site look, call (877) 610-2993.
Call Gatewood Fence & Gate for Gate Parts & Welding in Banning
If your gate is sagging, scraping, rattling in the wind, or the operator just gave up, call (877) 610-2993. We’ll answer. We’ll show up. We’ll quote a price before any work starts, and we’ll put the 90-Day Done Right Promise in writing on your invoice. Hal’s name is on the shop, and the shop is down the road, not three states away. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Banning and the San Gorgonio Pass since 2001.