Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Artesia, CA
Most gate repairs in Artesia run between $180 and $650, and the work usually comes down to one of three things: a hinge post that’s given way, a frame that’s rusted or cracked, or a motor that quit. Hal Gatewood has been fixing gates since 2001, and when you call (877) 610-2993, a live person answers, any hour of the day or night. We show up in Artesia, look at the gate in your driveway, and tell you the price before we touch a wrench.
Why Artesia Homes Are Different
Artesia sits about 12 to 15 miles inland from the Pacific, close enough that the marine layer rolls through most nights and leaves a film of moisture on everything metal. On the western side of the 90701 zip especially, we see steel hinge posts, latch hardware, and gate frames rusting from the bottom up, even when the visible parts look fine. You’ll notice it as a gate that still opens but makes a dry, scraping sound, or a latch that takes two hands to throw when it used to take one.
Then there’s the housing stock. Much of Artesia is 1950s to 1970s single-family homes on small lots, and a lot of those gates are anchored to original brick or block pilasters. Sixty years of settling later, a gate that “suddenly” started dragging usually has a post that’s leaning a few degrees, and the gate is just telling you about it. Fix the panel without the post and you’ll fix it twice.
Gate Repair in Artesia
Gate repair in Artesia usually starts with the post, not the gate. The city’s post-WWII tract homes, especially in the 90701 zip north of the 91, were built with gate posts set in concrete that’s now crumbled below grade. So a gate that sags, drags, or won’t latch is often sitting on a footing that’s given up. We fix the post first, then the gate stays fixed.
The other Artesia-specific problem is the marine layer. Properties along the western edge of the city get more overnight moisture, which means rusted hinges and seized latch hardware are common before the gate frame itself shows any damage. We repair what’s there rather than replacing panels that don’t need replacing. On-site welding means your gate stays in your driveway and you watch the fix happen.
Hinge Rehang
When a gate drags a groove into the concrete, the hinge post has usually moved. We rehang the gate on new heavy-duty hinges and realign the post if it’s still sound. On an Artesia gate, this runs $180 to $340.
Frame Straightening or Weld Repair
Cracked frames come from decades of use with a post that’s slowly leaning, or from Santa Ana winds that torque the panel against its stops. We weld the crack, box the joint, and straighten the frame in place. That work runs $220 to $450 depending on how far the damage has spread.
Gate Motor or Opener Repair
A gate that hums but won’t move on a 90702 back lot is usually a failed motor or a stripped gear, not a lost cause. We diagnose it the same trip. Most opener repairs in Artesia run $250 to $650, board and parts included in that range. We work with a Gate Repair approach that fixes the failure rather than swapping the whole unit.
How much does gate repair cost in Artesia?
Most residential gate repairs in Artesia run $180 to $650. The biggest variable is whether the post itself has failed. Call (877) 610-2993 for an exact quote, estimates are free.
Can you come out the same day in Artesia?
Yes. Artesia is only 1.6 square miles, so our response time across the whole city is consistent. We’re typically at your gate the same day you call for repair work, and we’ll give you a straight window.
Gate Installation in Artesia
A new driveway or pedestrian gate in Artesia typically runs $1,800 to $6,500 installed, and the job is usually scheduled within a week, not a month. The longer version involves Artesia’s particular housing stock, the way the marine layer eats at exposed steel, and the fact that a lot of gates here were bolted to pilasters poured back when Eisenhower was president.
Driveway Gate Installation
The classic Artesia driveway gate is a swing gate on a narrow lot, often flanked by brick or block pilasters from the original build. A new driveway gate in Artesia runs $2,200 to $6,500 depending on width, material, and whether we’re automating it. We measure the actual opening, check the pilaster stability, and quote the job before any work begins.
Pedestrian Gate Installation
For the side yard, the backyard, or the walkway from the driveway to the front door, a pedestrian gate in Artesia typically runs $700 to $1,900. These smaller gates are where we see the most moisture damage, because the marine layer sits on the lower hardware long after sunrise. We set new posts in fresh concrete, hang the gate with proper clearance, and use hardware rated for coastal air. This is part of our Gate Installation work we do across the city.
Sliding Gate Installation
Sliding gates make sense on Artesia properties where the driveway has no room for a swing arc. A new sliding gate installation here runs $2,800 to $7,000, with the track and roller hardware being the part you can’t cheap out on. The commercial lots along Pioneer Boulevard often need sliding gates with operators rated for daily traffic, not weekend use.
How fast can you install a gate in Artesia?
Most standard gate installations in Artesia are scheduled within a week, often sooner. We keep common gate frames, hinges, and hardware in stock locally, so we’re not waiting on a freight truck. Call (877) 610-2993 for a real answer about your specific street.
Do you work in all Artesia neighborhoods?
Yes. We cover the full city, including the residential streets off Pioneer Boulevard, the older 90701 neighborhoods near Artesia Boulevard and South Street, and the 90702 side toward Cerritos. If you’re inside Artesia city limits, we’re close enough to show up when we say we will.
Gate Motor & Opener in Artesia
If your automatic gate won’t open on Pioneer Boulevard or the opener’s humming but the gate won’t budge off Alburtis Avenue, we can tell you what’s likely wrong before we even show up. Gate motor and opener repair in Artesia runs $145 to $480 for most jobs, and a lot of what we see here isn’t actually the motor. It’s the post it’s bolted to, the hinge it’s fighting, or the rust that’s crept into the limit switch.
Motor Repair
Most motor repairs in Artesia cost between $145 and $480. That’s the honest range, whether it’s a DoorKing arm that’s lost its travel settings or a Ghost Controls board throwing error codes after a Santa Ana wind event knocked the gate off its track and stripped the gear. We see a lot of motors along the western edges of 90701 where overnight marine moisture accelerates rust on the control box internals. We carry the boards, gears, and limit switches to fix it same trip.
Motor Installation
New motor installation in Artesia runs $650 to $1,850 depending on the gate’s weight, swing or slide configuration, and whether we’re reusing existing conduit or running new line along a 90702 backyard wall. Post-WWII lots here are tight, which means a lot of gates open over driveway approaches that barely cleared a 1962 Ford Falcon. We measure, check the hinge posts, and tell you exactly what the opener needs before we touch a wire. See our Gate Motor & Opener page for the full scope of what we handle.
Linear Motor Swap
Linear arm openers are the workhorse of Artesia’s commercial corridor, especially along Pioneer Boulevard where a swung gate has to clear a sidewalk and a restaurant’s trash enclosure in eight feet of space. A linear motor swap or rebuild here typically runs $380 to $900, and we keep arm assemblies for the most common commercial units on hand.
Can you come out for an emergency gate motor repair in Artesia?
Yes, we answer the phone 24/7 with a live person, and we’ll come to Artesia for a gate that’s stuck open, stuck shut, or otherwise unsafe. A gate that won’t close on a Pioneer Boulevard storefront is a real problem at 11 PM. We treat it like one.
Is gate motor repair in Artesia more expensive than nearby cities?
No, our pricing is the same across Artesia, Cerritos, La Palma, Hawaiian Gardens, and Norwalk. What changes the price isn’t the city line; it’s the age of the posts, the weight of the gate, and whether someone’s been “fixing” it before we got there. Call (877) 610-2993 for a free estimate.
Gate Access Control in Artesia
Gate access control in Artesia covers keypads, intercoms, card readers, and telephone entry systems on both residential and commercial gates. The city’s dual nature, tract homes on one side of Pioneer Boulevard and a dense commercial corridor on the other, means we see a wider range of access systems here than in most nearby cities. Repairing or replacing an access control unit in Artesia runs $200 to $500 for most keypad and entry system failures.
Keypad and Entry System Replacement
A keypad that worked fine for years and now ignores the code usually has moisture in the housing or a worn membrane, both of which accelerate in Artesia’s coastal air. We replace the unit, re-pair the remotes, and test it thoroughly before we leave, typically in the $200 to $500 range.
Commercial Access Control
The storefronts on Pioneer Boulevard need access systems that work every day, all day, for employees, deliveries, and trash pickup. We service and replace DoorKing and Linear commercial keypads and card readers on tight urban lots where a failed entry system means a locked business. See our Gate Access Control page for details on systems we support.
Intercom and Telephone Entry
Older Artesia buildings, especially the multi-unit lots near the Cerritos border, often have telephone entry systems tied to gate motors from a different era. We modernize what’s there without replacing equipment that doesn’t need replacing. Most intercom repairs land between $200 and $500, and we quote it before we open a panel.
Do you handle access control on Artesia commercial gates?
Yes. We service access control on Pioneer Boulevard storefronts, restaurant loading areas, and small office lots throughout Artesia, including keypads, card readers, and intercoms. Call (877) 610-2993 for a free estimate on your system.
Can you integrate a new keypad with my existing gate motor?
Yes. We match the new keypad or reader to whatever motor you already have, whether it’s a Linear, Viking, DoorKing, or Ghost Controls. We test the whole setup before we leave. Call (877) 610-2993 for a straight answer about your existing equipment.
Gate Parts & Welding in Artesia
Welding a cracked gate frame or replacing a seized hinge in Artesia usually costs between $85 and $340, and most jobs we handle are done the same visit. If you’re reading this from a 1950s tract home off Pioneer Boulevard or from a shop near the 91, you already know the marine air works on steel around here faster than a lot of people expect.
Gate Hinge Replacement
Hinges fail before gate frames do, especially on the western side of Artesia where overnight marine moisture adds rust to anything exposed. We remove the old hinge, grind the mounting surface clean, and weld or bolt a new heavy-duty hinge in place. In the 90701 zip especially, half the hinge calls we take end up being post calls once we start digging into why the gate leaned. Hinge replacement runs $95 to $240 per hinge.
Gate Post Replacement
Old Artesia gate posts were often set into concrete footings that have crumbled below grade. A wobbly post isn’t a gate problem, it’s a footing problem. We pull the old post, set a new steel post in fresh concrete, and have the gate re-hung the same day in most cases. A full post replacement with new concrete usually lands between $280 and $520. Our Gate Parts & Welding crew does this work in the driveway, not in some far-off shop.
Custom Welding
Sometimes the part you need was never mass-produced. A bracket for a gate motor mount, a latch plate with a weird offset, a hinge pattern for a gate that’s no longer made. We do custom welding on site in Artesia, cutting and shaping steel to fit the gate as it sits. Custom jobs start around $120 for small brackets and run up from there based on material and time.
How much does hinge replacement cost in Artesia?
Hinge replacement in Artesia typically runs $95 to $240 per hinge depending on the size of the gate and the condition of the post. Call (877) 610-2993 for an exact quote, and we’ll tell you if the post needs attention too.
Can you weld my gate in the driveway instead of hauling it away?
Yes. On-site welding is exactly what we do. Your gate stays in your driveway in Artesia, and we cut, weld, and finish the repair on site. It’s faster and you see the work as it happens.
Brands We Service in Artesia
We’re certified to service nine major gate brands, including Linear, Viking, Ghost Controls, and DoorKing. We stock common boards, arms, and limit switches for these brands locally, which means most repairs in Artesia are done same trip. See our brands page for the full list.
Pricing for Gate Repair in Artesia, CA
| Service | Typical range in Artesia |
|---|---|
| Hinge rehang (residential swing gate) | $180 - $340 |
| Weld repair or frame straightening | $220 - $450 |
| Gate motor or opener repair | $250 - $650 |
| Full panel replacement or new pickets | $400 - $900 |
| Access control or intercom repair | $200 - $500 |
| Pedestrian gate installation | $700 - $1,900 |
| Driveway swing gate installation | $1,800 - $5,500 |
| Sliding gate installation (residential) | $2,800 - $5,500 |
| Slide motor repair | $220 - $650 |
| Hinge replacement (per hinge) | $95 - $240 |
| Post replacement with new concrete | $280 - $520 |
| Rail repair | $180 - $420 |
In Artesia, the two things that push a quote toward the top of these ranges are posts that need rebuilding and gates that automation was added to without the structure being checked first. Every price is quoted and agreed before we start, and what we tell you is what it costs.
Neighborhoods We Serve in Artesia
Artesia is only 1.6 square miles, so our response time across the whole city is fairly consistent. We’re typically at your gate the same day you call for repair work, and we’ll give you a straight window. We serve:
- The residential streets around Artesia Park and Artesia High School
- The Pioneer Boulevard commercial corridor from 183rd Street down to South Street
- The older 90701 neighborhoods north of the 91 Freeway
- The 90702 residential pockets along the Cerritos border
- Homes along the western edge of the city, where rust from coastal moisture shows up first
Service Area - Cities Near Artesia
Beyond Artesia, CA, we serve the surrounding communities in the same county with the same pricing and the same upfront quotes. That includes Cerritos, CA to the east, La Palma, CA to the northeast, Hawaiian Gardens, CA to the south, Norwalk, CA to the north, and Bell, CA to the northwest.
Serving Artesia, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Artesia and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Artesia coverage area; if your address is on it, we can help.
Also serving nearby: Artesia, CA, Cerritos, CA, La Palma, CA, Hawaiian Gardens, CA, Norwalk, CA, Bell, CA.
FAQs About Gate Repair in Artesia
We can usually reach Artesia the same day you call, often within a few hours. Because the city is so compact and we’re frequently working along Pioneer Boulevard or near the 91, we’re never far. Call (877) 610-2993 and we’ll tell you exactly when we can be there.
Most straightforward gate repairs and replacements in Artesia don’t need a permit, especially if you’re reusing existing posts. If your job involves new footings or a change to a driveway approach, we’ll tell you what’s required before we start. We won’t quote a job without checking.
Yes. We serve the entire city of Artesia, including both the 90701 and 90702 zip codes. That covers the residential streets near the Cerritos and Norwalk edges, the Pioneer Boulevard commercial corridor, and the older tract home neighborhoods in between.
Call (877) 610-2993 for a free estimate on any gate repair, installation, or motor job in Artesia. A live person answers, the price is firm before we start, and every job carries the 90-Day Done Right Promise in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Artesia Customers Say
"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth