Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Acworth
A sagging gate or a hinge that’s pulled loose from the post isn’t something to put off, especially here in Acworth where the red clay works against you every season. We’re Gatewood Fence & Gate, and our Gate Parts & Welding crew handles hinge replacement, post rebuilding, rail repair, and custom welding on gates throughout 30101 and 30102. Hal Gatewood has been at this since 2001, and he still runs every job like his name is on it because it is. If your gate is binding, dragging, or pulling away from a hinge post, call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Acworth’s Preferred Gate Parts & Welding Company
Most of the gates we work on in Acworth are 20 to 25 years old. That’s not a guess, it’s the pattern. The late-1990s HOA boom put hundreds of ornamental iron and aluminum swing gates into Cherokee County subdivisions, and that entire generation of hardware is now reaching the end of its first life cycle at the same time. Hal and his crew know what that means in practice: hinge posts poured into expansive red clay, legacy openers still wired to old control boards, and gate panels that were never re-hung after the first owner sold. When you call us, the person who shows up has seen your exact gate a hundred times before.
We answer the phone live 24/7. No voicemail, no call center somewhere else. Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right, one call brings Hal back. And because our dispatch is coordinated from the brand’s Atlanta office, crews serving Acworth locally can often schedule same-week work without making you wait on a national outfit that doesn’t know Bells Ferry Road from Main Street. Estimates are free, and the price we quote is the price you pay, agreed on before any work starts.
Our Gate Parts & Welding Services in Acworth
Hinge Replacement
Hinges on Acworth gates rust from humidity, wear from daily use, and pull loose when a post starts leaning. A gate sags in the hinge post, not in the middle, and that’s where we start. We remove the old hinge, check the post for plumb, weld or bolt a new hinge in place, and re-hang the gate so it swings clean instead of dragging the latch side into the ground. A hinge replacement in Acworth typically runs $180 to $420 depending on gate weight and whether the post needs reinforcement first.
Post Replacement
This is the big one in Acworth. The red clay throughout 30101 and 30102 expands when it’s wet and contracts in summer drought, which slowly walks gate posts out of plumb year after year. A gate that binds or reverses on its opener often has a healthy motor and a hinge post that’s tilted a full inch or more out of vertical. We cut the old post, dig the footing deeper than the original builder did, set new steel, and weld the gate back onto a post that will actually stay put. Post replacement jobs in Acworth run $600 to $1,400, and yes, we handle them on HOA entrance gates as well as private driveways.
Rail Repair
Older ornamental iron gates sag upward at the latch side as the bottom rail corrodes internally. Humidity in this area accelerates rust pitting on hinge welds and rail brackets, and you’ll often see it before you feel it: flaking paint, orange staining at the welds, and a gate that suddenly needs a lift to latch. Hal’s approach is repair-first. If the rail is structurally sound, we cut out the bad section and weld in new steel, match the finish, and send you on your way. A rail repair in Acworth typically runs $250 to $600 depending on the length of the corroded section.
Custom Welding
Not every gate problem is a broken part. Sometimes the gate itself was built for a different post spacing, or the original builder’s weld never had a chance from day one. We do custom welding on site, in your driveway, so the gate never leaves your property. That includes re-welding hinge mounts, reinforcing cracked rails, building up worn latch plates, and adding steel where the original design was too light. Custom welding in Acworth runs $150 to $450 for most repairs, and we’ll give you a written quote before the first weld.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Acworth
We’re certified on nine major gate brands, and in Acworth we most often see Linear, Viking, and Ghost Controls operators on older swing gates, plus the occasional DoorKing on commercial entrance systems. We keep common parts for these brands stocked on the truck, which means a hinge or a limit-switch replacement doesn’t have to wait on a special order. If you have a legacy opener that’s been discontinued, we’ll tell you honestly whether the board can be rebuilt or whether you’re better off putting the money toward a new operator matched to your existing gate.
Common Gate Parts & Welding Problems We See in Acworth Homes
- Post lean from expansive red clay. The soil in 30101 and 30102 swells when wet and shrinks when dry. Over a decade or two, that cycle works hinge posts out of vertical. The gate binds mid-swing, the opener strains, and the owner assumes the motor is failing. It’s usually the post.
- Rust-pitted hinge welds on older iron gates. Georgia humidity gets inside the paint at the weld joints. The steel corrodes underneath, the hinge loses its hold, and the gate drops. This shows up as a gate that scrapes the ground at the latch side or won’t stay shut.
- Legacy operator failures on 20-plus-year-old gates. Acworth’s HOA boom gates from the late 1990s are all aging at once. Control boards fail, gears strip, and old limit switches drift. Sometimes the operator is worth rebuilding, sometimes replacement is cheaper than the repair.
- Ice storm damage to gate arms and tracks. Acworth’s winter ice storms are rare but severe. When ice loads a gate mechanism that wasn’t designed for it, the arms bend and the racks skip. We see a spike in weld and roller repairs after every freeze event.
Pricing for Gate Parts & Welding in Acworth, GA
We’ll quote your price before any work begins, in writing, and that’s the number you’ll pay. Here’s what to expect in the Acworth market:
- Hinge replacement: $180 to $420, depending on gate weight and post condition
- Post replacement with new footing: $600 to $1,400, more for HOA entrance gates with larger posts
- Rail repair and re-welding: $250 to $600 based on the length of the corroded section
- Custom welding, latch reinforcement, or hinge mount rebuild: $150 to $450
- Gate roller and track work: $120 to $350 for most residential slide gates
Most of what drives cost in Acworth is post condition, because the clay here has been working against the footing for 20 years. We’ll look at the gate, tell you what’s actually failing, and give you a number. Free estimate, no trip charge inside the county, and $40 off any repair over $200. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Acworth
If you’re in Kennesaw, Woodstock, Holly Springs, or Marietta, our crews work those areas too, with the same live-answer phone and the same written promise. We know north metro Atlanta’s gate problems because we’ve been fixing them since before a lot of the current subdivisions were even built. Whatever city you’re calling from, the person who shows up has seen your gate before. You can read more about Gate Parts & Welding in Acworth or call (877) 610-2993.
Serving Acworth, GA - Our Local Coverage Area
We’re based in the Acworth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Acworth
The fastest check: disconnect the opener and swing the gate by hand. If it swings freely, the motor or limit switch is the issue. If it still drags or binds at the same spot, the hinge post has moved. In Acworth, we find post lean more often than motor failure on gates over 15 years old. Call (877) 610-2993 and we’ll confirm it on site, free.
If the board hasn’t failed and the gears show life, we can often rebuild the operator: new limit switches, fresh capacitors, and a cleaned or replaced gear set. But if the board is already dead or the motor’s windings have burned out, a new operator is usually cheaper than piecing together a legacy unit. We’ll show you the failure and quote both paths.
It’s the red clay, and it’s not going to stop. The soil expands when saturated and contracts in drought, pushing shallow footings out of plumb. Fix the post with a deeper footing, and the problem stays fixed. Patch it with brackets, and you’ll be calling us again in two years. That’s why we set our post footings deeper than the original builders did.
Sometimes. If the rack has pulled away from the gate frame, yes, it’s a re-weld job. If it’s just a worn gear on the operator output shaft, it’s a mechanical replacement. Often the rack is fine and the gate’s rollers have failed, letting the whole gate ride low and chew up the rack. We’ll weld it if it needs welding, replace it if it doesn’t.
Yes. Current code and UL 325 standards require automatic gates to have entrapment protection: either photo-eyes at the gate opening or edge sensors that reverse the gate on contact. A lot of the late-1990s gates around Acworth were installed before those rules, and we bring them up to standard when we’re on site. That’s a repair with a real safety consequence, and it’s one job you don’t want a handyman guessing at. Call us at (877) 610-2993 and we’ll take care of it.
Call Gatewood Fence & Gate for Gate Parts & Welding in Acworth
If your gate is sagging, dragging, or failing at the post, call (877) 610-2993. Hal Gatewood has been fixing gates in north Georgia since 2001, and he’ll tell you straight whether that 24-year-old gate needs a weld, a new post, or an honest conversation about replacement. Free estimates. Upfront pricing agreed before any work starts. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Acworth since 2001.