Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Moore
Gate motor repair in Moore typically runs $180 to $420 for most common failures, and a full operator replacement usually lands between $650 and $1,250 depending on the motor and gate type. Those are the numbers you should hear before anyone touches your gate. We have been fixing and installing gate motors in Moore long enough to know which failures happen street by street, especially in the post-2013 rebuild neighborhoods. Call (877) 610-2993 and you will reach a live person who can tell you what to check first.
Moore’s weather does not just wear out gate motors. It breaks them in predictable ways. Straight-line winds twist solid privacy gates, clay soil heaves posts out of plumb, and storm-season power cuts leave homeowners wondering how to get their own gate open without wrecking the operator. Hal Gatewood has been repairing gates in this area since 2001. The company is still owner-operated, and the name on the invoice is the guy who picks up the phone. Scheduling is coordinated from the Oklahoma City office, with local crews serving Moore throughout the week.
Why Gatewood Fence & Gate Is Moore’s Preferred Gate Motor & Opener Company
Moore residents have seen plenty of out-of-town outfits show up after a storm, quote one price on the phone, and hand over a different invoice once the work is done. Hal built Gatewood Fence & Gate to be the opposite of that. The shop address is published. The license number is published. Nobody hides behind a call center. When you call about a gate motor that stopped working on your side of SW 34th Street, you talk to a person who knows exactly which subdivision you are describing.
The 90-Day Done Right Promise is written on every job, not explained away in fine print. If the repair was not done right, one call brings us back. No runaround, no re-quote. That promise matters double in Moore because so many post-2013 rebuild gates were installed in bulk, and a small mistake in travel limit calibration will resurface within weeks, not months.
Hal and his crew work throughout Moore and the surrounding communities, from the older blocks near I-35 to the newer subdivisions that went up east of Bryant Avenue. The same techs come back for warranty work. You might see the same truck at the hardware store later that week. That is the point.
Our Gate Motor & Opener Services in Moore
Our Gate Motor & Opener work covers everything from a single failed limit switch to a full slide gate operator replacement. Here is what that looks like on the ground in Moore.
Motor Repair
Most Moore gate motor failures come down to one of three things: water in the control board, a stripped gear from fighting a wind-shifted post, or limit switches that were never calibrated after the 2013-era installs settled. We open the operator on site, find the fault, and replace only what actually failed. We do not sell you a new motor when a $60 limit switch fixes the problem. Hal has been known to get genuinely irritated when he finds a perfectly good operator swapped out for no reason by someone else.
Motor Installation
A new gate motor in Moore needs to survive wind loads that most manufacturers do not size for. We recommend operators with enough torque margin for solid infill gates that catch Oklahoma wind like a sail. When we install a new motor, we also check the post footings and hinge alignment first. A brand-new operator bolted to a gate that already sags in the hinge post will eat its own gears within a season. That is not a motor problem. That is a post problem, and we fix it before we mount anything.
Linear Motor
Linear arm operators are common on Moore’s ranch-style driveway gates, especially in subdivisions rebuilt with matching vinyl privacy gates. These units are reliable until water gets into the arm seal or a misaligned gate forces the screw drive to over-torque. We service Linear, LiftMaster, FAAC, BFT, and Viking operators. If the arm is worn but the control board is fine, we replace the arm. If the board is fried, we do not sell you an arm too.
Slide Motor
Slide gates are less common in Moore than swing gates, but they show up on wider driveways along 73160’s newer builds east of Sunnylane Road. Slide operators fail in Moore mostly because rack and pinion teeth get knocked out of alignment when storm winds shove the gate panel sideways. We re-align the rack, reset the travel limits, and replace stripped gear teeth. We also do sag correction on slide gate trucks so the panel does not drag through the bottom track and overload the motor.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Moore
We are certified to service nine major gate operator brands, including FAAC, BFT, Linear, and Viking, plus LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule. Moore homeowners who had builders install LiftMaster or Linear units in the 2013-2015 rebuild wave are especially well served here, because we keep the common boards, remotes, and gear kits for those units on the truck. That means less waiting on a parts shipment and a faster fix when the gate will not close at 7:30 on a Thursday evening.
Common Gate Motor & Opener Problems We See in Moore Homes
- Wind-shifted posts from straight-line storms. A solid vinyl privacy gate in Moore acts like a wall in 60 mph gusts. The hinge post takes the load, the post tilts in saturated clay, and the operator starts fighting the misalignment every single cycle until something strips.
- Synchronized hardware failures in post-2013 rebuild neighborhoods. Thousands of homes in Moore got matching builder-grade gates installed in one wave after the tornado. Those stamped hinges and light-duty latches wear out on the same timeline, so when one house on a block needs work, three more usually follow.
- Power cut panic on storm warning nights. When the sirens go off and the power drops, many Moore homeowners do not know how to open their gate manually. They force it, the internal clutch shears, and the operator needs a rebuild that could have been avoided with a quick manual-release lesson.
- Clay heave under post footings. Moore sits on expansive shrink-swell clay that moves through wet and dry cycles. Footings saturated during April-June storms heave upward, the gate post tilts, and the motor burns out trying to drive a gate that no longer closes square.
Pricing for Gate Motor & Opener in Moore, OK
We quote the price before any work starts, and the number on the estimate is the number on the invoice. No trip charge inside the county. No fuel surcharge. No surprise “installation adjustment” when the tech arrives.
- Motor repair, minor (limit switch, remote board, capacitor): $180-$280
- Motor repair, major (gear replacement, arm rebuild, clutch): $280-$420
- New operator installation (swing or slide, standard residential): $650-$1,250
- Battery backup system installation: $350-$700
- Manual release retrofit or repair: $120-$220
Senior and veteran discounts take 10% off every job, permanently. And repairs over $200 take $40 off. We also give a free second opinion on any written estimate from another company: bring us the paperwork, and we will tell you plainly whether that work is needed and whether the price is fair. That is not a marketing gimmick. Hal has been doing it for years because he likes taking apart bad estimates.
We Also Serve Cities Near Moore
While this page covers Gate Motor & Opener in Moore, our techs regularly run calls to Del City, Norman, Midwest City, and Newcastle. The soil, the weather, and the gate stock are similar across the metro, so what fixes a gate near SW 19th Street fixes one near the Norman city line too.
Serving Moore, OK - Our Local Coverage Area
We’re based in the Moore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Moore
Most residential swing and slide gate operators have a manual release mechanism, usually a pull handle or keyed cylinder on the operator itself. On LiftMaster and Linear units, the release is typically a red or yellow handle below the motor housing. Pull it and the gate should swing or slide freely by hand. Do not force a powered gate open without disengaging the release: you will strip the internal clutch or shear the limit switch contacts, and that turns a power outage into a $300 repair. If you cannot find the release on your operator, call us at (877) 610-2993 and we will talk you through it over the phone, even during a storm night.
The 2013 EF5 tornado triggered a single-wave rebuild that installed thousands of matching builder-grade swing gates across entire Moore subdivisions. Same hinges, same posts, same operators, same installers, same week. Those gates share a near-identical hardware life cycle, so whole streets now enter their motor replacement window together. In the Mayfield addition near SW 19th Street, where the rebuild put in dozens of vinyl privacy gates in one pass, our tech replaced a LiftMaster swing gate operator that had stripped its internal gears after years of fighting a wind-shifted post. We reset the post footing in oversaturated clay, swapped the hinge post bracket to correct the sag, and reprogrammed the travel limits so the gate stops binding on its latch side. When you see three truck-and-trailer setups on your street all getting gate work at once, it is not a coincidence. It is the rebuild cycle catching up.
Yes, a battery backup keeps the operator running through short outages, which is common in Moore during April through June. It will not power the gate indefinitely, but it gives you enough cycles to get vehicles in and out safely when the grid is down. We install battery backup systems on most major residential operator brands, including FAAC and Viking swings and Linear slide units. If your gate currently has no backup and you live in Moore, consider it before storm season rather than during the first warning.
Moore’s expansive clay soaks up heavy spring rain, heaves, and tilts the hinge post just enough to pull the gate out of plumb. The operator still tries to close the gate level, so it pushes harder with every cycle. That constant over-torque burns out the motor or strips the gear train, depending on which gives first. We correct the sag at the post, re-set the footing if needed, and then recalibrate the operator. Fix the panel without the post and you will fix it twice.
Yes, all automatic gate operators installed in Oklahoma must comply with UL 325 entrapment-protection standards, which include photo eyes, edge sensors, or reverse-sensing mechanisms. If your Moore gate operator was installed during the post-2013 rebuild and has never been retrofitted, it may not meet current safety requirements. This is not a paperwork detail: a solid gate closing on a child or a pet is a genuine risk. We check entrapment protection on every service call and will tell you honestly if your operator needs a safety upgrade.
Call Gatewood Fence & Gate for Gate Motor & Opener Work in Moore
If your gate motor is groaning, refusing to close, or dead after last night’s storm, call (877) 610-2993. A live person answers, day or night. We will ask what the gate is doing, give you a straight answer on what it probably needs, and schedule a time that actually works. The estimate is free. The price is agreed before work starts. And if we fix it wrong, you have 90 days to call us back, and Hal will make it right himself.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Moore since 2001.