Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Jeannette, PA
Gate repair in Jeannette typically costs $180-$390 for most electric operator issues, and $235-$455 for hinge and post resets on older alley gates. Most repairs are finished in one visit because we weld on site and carry common parts for major brands in the truck. Call (877) 610-2993 and you’ll reach a live person, not a recording.
Jeannette’s identity as a legacy glass-manufacturing mill town means its residential neighborhoods are packed with early 1900s to 1940s working-class row homes and bungalows, most built with rear-alley access and alley-facing gates that are now 60-100+ years old. These original wrought-iron and early mild-steel gates have spent decades exposed to western Pennsylvania’s aggressive freeze-thaw cycles, leaving hinge pins seized, posts heaved out of plumb, and metalwork deeply pitted with rust - making restoration and re-setting work far more common here than simple latch replacements. We work those alleys every week, and we’ve learned that fixing the panel without fixing the post means fixing it twice.
Why Jeannette Homes Are Different
The bulk of Jeannette’s housing stock dates from roughly 1900-1950, built during the city’s glass-industry boom as dense, narrow-lot worker housing. Rear yards commonly face brick-paved or gravel alleys, and original iron or early tubular-steel gates serving those alley entries are frequently still in place, heavily corroded and with footings that have shifted after a century of frost cycles.
Westmoreland County averages 40-50 inches of annual snowfall and endures repeated hard freeze-thaw events each winter. Standing meltwater pools in low-lying alley corridors, accelerating rust on gate hardware and causing concrete post footings to heave and crack season after season. Gate hinges and latches that go unlubricated heading into winter frequently seize solid by February.
In Jeannette’s older grid neighborhoods, alley-gate posts are often set directly into century-old brick borders or crumbling mortar beds rather than proper concrete footings, so a “sagging gate” call frequently turns into a full post-reset job once we discover the original installation was never footed to frost depth. That’s the reality we plan for on every service call in the 15644 zip code.
Gate Repair in Jeannette
Gate repair in Jeannette usually means one of two jobs: a hinge pin that seized solid over the winter, or a post that heaved out of plumb because it was set in a century-old brick border instead of a concrete footing. We handle both in your alley, in your driveway, or wherever the gate actually lives. Our crew works Jeannette’s alley corridors regularly, and we bring the welder to you so the gate never leaves your property.
Hinge & Post Repair
In Jeannette, this is the job we do most. The old alley gates were hung on posts set directly into brick borders or crumbling mortar beds. Freeze-thaw cycles push those posts a little further out of plumb every winter, and by spring the gate is dragging on the alley gravel. We dig the post, set a proper concrete footing below the 36-inch frost line, and re-hang the gate so it swings clean. A typical hinge and post re-set runs $235 to $455, depending on whether we’re digging one post or two and how much concrete we’re pouring. Fix the panel without the post and you’ll fix it twice. We learned that in Jeannette’s alleys.
Gate Realignment
A gate that scrapes, binds, or won’t latch anymore is usually fighting a shifted post or a worn hinge pin. In Jeannette’s older grid neighborhoods, the problem is almost always the footing. We re-set the geometry from the post out, then re-hang and adjust the latch so the gate closes square and stays closed. Gate realignment on a swing gate runs $120 to $210. We do on-site welding when the hinge plate has wallowed out, so the gate never has to leave your driveway. That’s the difference between a repair and an ongoing headache.
Electric Gate Repair
Electric gate operators in Jeannette take a beating from the weather. Cold snaps stiffen the grease, snowmelt pools around the motor housing, and freeze-thaw cycling knocks safety photocells out of alignment every spring. We service LiftMaster, Linear, Viking, Ghost Controls, and DoorKing operators, and we keep common parts on the truck so most electric gate jobs are done in one visit. Electric gate repair runs $180 to $390 for most single-operator jobs. If the operator is beyond saving, we’ll tell you straight, and we’ll quote a replacement at the same visit. No second trip just to deliver the news. For more on our full Gate Repair capabilities, have a look around the site.
Why does my Jeannette alley gate swing into the neighbor’s yard after every winter?
Your gate post was probably never footed below the frost line. In Jeannette’s early-1900s worker row-home grid, original posts were often set directly on brick borders or shallow concrete caps, not the 36-inch-deep footings a gate post actually needs. Freeze-thaw cycling heaves the post out of plumb, the gate leans, and the swing widens until it crosses the property line. We fix it by digging to frost depth and pouring a proper footing.
How do you fix a sagging 90-year-old iron gate without replacing it?
You fix the post, not the panel. A gate sags in the hinge post, not in the middle. On Jeannette’s original wrought-iron and early mild-steel gates, the hinge pins are usually worn oval and the post has leaned. We dig the post, set fresh concrete below frost depth, weld new hinge barrels or ream the old ones, replace the pins, and re-hang the gate level. If the frame itself has rusted through, we’ll tell you straight whether welding will hold or if it’s time to talk about a new gate.
Gate Installation in Jeannette
A new driveway gate in Jeannette typically costs $2,800 to $8,500 installed, with sliding gates running higher than swing gates because of the track, motor, and safety work involved. Most installations are completed in one to two days once materials arrive. In Jeannette, most gate work happens at the alley, not the front curb, and that changes everything about how we measure, design, and build.
Rear-Alley Driveway Gates
Driveway gates in Jeannette are usually rear-facing, opening off a gravel or brick alley to a carport or detached garage. You need a gate that opens inward or slides, because a swing gate opening outward can block the entire alley, and that’s a dispute with your neighbor waiting to happen. We measure, order, and install the gate, operator, and safety equipment to fit the actual space, not a guess. A single swing driveway gate, manual, runs $2,400 to $4,800, while a single slide driveway gate, manual, runs $3,200 to $6,200. Call (877) 610-2993 for a free measure and a written price.
Sliding Gates for Tight Alleys
In Jeannette’s older grid neighborhoods, sliding gates are often the only option that fits. A rear alley 10 or 12 feet wide leaves no room for a gate arc. A slide gate rides on a track or cantilever, needs no clearance behind the opening, and keeps the alley passable. We install rack-and-pinion slides with operators, loop detectors, and safety photocells. If you’re on a narrow brick alley off South 4th or Clay Avenue, this is probably your gate. An automated driveway gate with operator, safety devices, and wiring runs $6,000 to $12,000 depending on gate length, access, and electrical run.
Post Work: The Hidden Cost
What moves the price in Jeannette is the post work. If your existing posts are heaving or rusted at the base, which is common in the older alley grid, you’re looking at $700 to $1,500 per post to dig, re-pour at frost depth, and set new steel. The gate itself is often the cheaper part of the job. We won’t set a post shallower than 42 inches, no matter what was there before. Every quote is written, agreed before we start, and that’s the number on the invoice. For more on our full Gate Installation capabilities, have a look around the site.
Why do so many Jeannette alley gates need a full post reset instead of just a hinge repair?
The original posts in Jeannette’s alley grid were frequently set only 12 to 18 inches deep into brick borders or loose mortar instead of concrete footings reaching below the frost line. After decades of freeze-thaw in Westmoreland County, those posts lean, heave, and rust at the base, so the gate will never hang true until the post is replaced and re-footed to 42 inches. Call (877) 610-2993 and we’ll tell you what you’re looking at after a quick look.
Can I install a swing gate across my Jeannette alley entrance, or do I need a sliding gate?
Most Jeannette rear alleys are 10 to 12 feet wide with shared access, which leaves no room for a swing gate to arc without blocking your neighbor’s garage or the alley itself. If your gate has to open outward and there isn’t 15-plus feet of clear depth, a sliding gate is almost always the only workable option and often the only code-compliant one. We’ll measure it and tell you what fits.
Gate Motor & Opener in Jeannette
If your automatic gate in Jeannette stopped opening, won’t close all the way, or groans through its travel after the last storm, the problem usually isn’t just the motor. It’s the post it’s bolted to. In Jeannette’s older alleys, gates built in the 1920s through 1940s often sit on posts that were never footed below frost depth, and Westmoreland County’s freeze-thaw cycle has been heaving them out of plumb for decades. We fix that from the ground up.
Motor Installation on Shaky Posts
A new automatic gate opener in Jeannette has to start with the post, not the package. On older alley gates near High Street and the A Street corridor, we’ll check the hinge post before mounting anything. If that post sits in a crumbling brick border instead of concrete, a new motor won’t fix the sag, and it’ll bind or burn out. We reset, re-foot, and plumb the post before the opener ever goes on, then mount the operator true and set the travel limits correctly. If the post needs to be re-footed first, add $350 to $700 for excavation, concrete, and re-setting.
Motor Repair vs. Replacement
Most Jeannette repair calls are not a dead motor. They’re a seized hinge, a stripped gear from years of fighting a heavy leaf, or a corroded terminal in the control board. We open the unit on site, find the actual failure, and fix what failed. A motor repair typically runs $180 to $360 for parts and labor when the drive unit itself is salvageable. We carry capacitors, relays, limit switches, and gear assemblies for the common brands, and we weld brackets and repair panels in the driveway rather than hauling the gate to a shop forty miles away.
Slide Motors in Wet Alleys
Slide gate openers on wider driveways in Jeannette’s newer sections see their own set of problems: wheels that rust onto their axles, track that fills with ice and grit, and rack brackets that shear from the force of waterlogged gates. We unseize wheels, repair or replace rack sections, and adjust force settings so the motor isn’t working against frozen rollers. A full slide motor replacement starts around $750 and can climb to $1,400 on heavier commercial-style gates. If the gate is older and worth keeping, we’ll make it slide true again rather than talking you into a replacement. For more on our full Gate Motor & Opener capabilities, have a look around the site.
Why did my Jeannette alley gate opener stop working after the last big windstorm, even though the gate still closes by hand?
Because the storm moved the post, not the gate. Wind load on a solid infill gate shoves the whole assembly against a hinge post that was likely never footed below frost depth, shifting it out of plumb and binding the opener mid-stroke. If the gate swings freely by hand, the opener may need a force adjustment, a limit reset, or a new shear pin. More often the real problem is the post, and we fix that first.
My Jeannette row home has an original 1920s wrought-iron gate on an alley post. Can you put a new motor on it, or does the post need to be replaced first?
We can automate that gate only if the post is plumb, solid, and footed below frost depth. In Jeannette’s older grid neighborhoods, many of those posts were set directly into brick borders or shallow mortar. A new motor on a post that leans will bind, burn out, or strip its gear in a season. We’ll set the post right first, even if that means breaking out the old mortar and pouring fresh concrete to 42 inches.
Gate Access Control in Jeannette
Gate access control in Jeannette means keypads, card readers, phone entry, and video intercoms built to work on old gates, tight alleys, and freeze-thaw ground. A keypad entry system on a Jeannette alley gate typically runs $850-$1,600 installed, and a card reader job usually lands between $900 and $1,700, depending on the post condition and how much masonry work is underneath. If your gate post has heaved or your keypad works only when the gate sits perfectly still, that’s not a keypad problem - it’s a post problem, and we address it first.
Keypad Entry on Shifting Gates
Keypad entry in Jeannette works best when the gate post is solid and the gate swings or slides without binding. On older alley gates, we often need to address the post before we mount the keypad - a post that heaves an inch in a February thaw will throw off the striker alignment, and the keypad will get blamed for the misread. We set the footing deeper than the Westmoreland County frost depth, re-hang the gate, and then program your codes. A keypad entry install on a sound post runs $850-$1,300. If the post needs to be pulled and a new footing poured to frost depth, the full job lands around $1,500-$2,200.
Card Readers Without Alley Power
Card readers on Jeannette alley gates face a real problem: power. Many alleys have no outlet anywhere near the gate. We solve that with low-voltage runs back to the house, solar options where the roofline allows, or battery-backed readers that last through a western Pennsylvania winter. Card reader installations run $900-$1,700, depending on the power run from the house. If you have employees or caregivers coming and going, a card reader gives you a record of who opened the gate and when - and you can revoke a card without changing everyone else’s code.
Video Intercoms for Blind Alleys
Video intercoms in Jeannette make the most sense on homes where the alley gate is out of sight from the back door. You can see who’s at the gate, talk to them, and open it from inside the house or from your phone. Video intercoms start at $2,200 for a basic one-camera system with an inside monitor, and go up if you want phone integration and a heated housing. We install systems that survive Westmoreland County winters - sealed buttons, heated camera housings where needed, and wiring run inside conduit so ice and salt don’t chew through it. For more on our full Gate Access Control capabilities, have a look around the site.
Can you install a keypad entry system on a gate whose post is set in an old brick alley wall in Jeannette?
Yes, in most cases. The difference is that we address the post before we mount the keypad. Old brick alley walls in Jeannette are often crumbling at the mortar line, and a keypad bolted to a loose brick will misread within a season. We epoxy-anchor the mounting plate, rebuild the mortar bed where needed, and if the post itself has heaved, we pull it and set a concrete footing to frost depth before the keypad goes on.
My swing gate sags and the keypad works only sometimes. Is that a keypad problem?
No, almost never. The keypad is sending the signal; the gate is just not aligning with the latch. When a hinge post on a Jeannette alley gate shifts on a shallow, frost-heaved footing, the gate drops and the striker misses. The keypad gets the blame, but the post is the culprit. We reset the post, re-hang the gate so it closes square, and then test the keypad - it works every time after that.
Gate Parts & Welding in Jeannette
Gate parts and welding in Jeannette is restoration work more often than replacement. The original wrought-iron and early mild-steel gates in this city’s alley corridors were built to last, but 60 to 100 years of western Pennsylvania weather takes its toll. We weld on site in your driveway or alley, so the gate never leaves your property. That matters with these older gates because the steel is often too brittle to haul across town.
Hinge Replacement
On Jeannette’s older alley gates, the hinge pins are usually the first thing to fail. Original iron pins seize up from decades of freeze-thaw cycles and standing meltwater in the low brick alleys behind the row homes. We torch out the rusted pins, weld new barrel hinges onto the existing gate frame, and re-hang it so it swings true. If the hinge itself is fine but the post moved, we fix the post, not the hinge. A hinge replacement on a typical Jeannette alley gate runs $180-$320 per hinge.
Post Replacement & Resetting
This is where Jeannette is different from the newer subdivisions. In the older grid neighborhoods, gate posts were often set into century-old brick borders or crumbling mortar beds, not proper concrete footings. Frost pushes them out of plumb every winter, and by spring the gate drags on the bricks. We cut the old post free, auger a new footing below frost depth, set a galvanized post, and re-weld the hinges. A full post replacement in Jeannette typically runs $400-$700 including concrete and cleanup.
Rail Repair & Custom Welding
Original mild-steel rails on Jeannette’s older gates rust through at the bottom rail first. That’s where meltwater sits and where gravity does its slow work. Sometimes the rust is surface-level and we can grind it back and weld a reinforcing plate. Other times the rail is too far gone and we cut out the bad section and weld in fresh steel to match the profile. Rail repair work in Jeannette generally runs $150-$350 depending on how much needs to be cut out and re-welded. Custom welding rates start around $120 for a simple repair and run up from there based on the amount of steel and time involved. Hal will tell you the price before he strikes an arc. For more on our full Gate Parts & Welding capabilities, have a look around the site.
My 80-year-old Jeannette alley gate sags and scrapes the bricks. Do I need a whole new gate or just a hinge post fix?
In most Jeannette alleys, the sag comes from the post, not the gate. Older posts were often set into brick borders or shallow mortar, and decades of frost have pushed them out of plumb. We reset the post in a proper concrete footing below frost depth and re-weld the hinges. The gate itself is usually fine. A new gate only makes sense if the rails and pickets are rusted through past saving.
Our rear-alley gate is original to our 1920s bungalow, and the hinge pins are seized. Can you free them without cutting?
Sometimes, but not usually. If penetrating oil and heat break the pin free, we can save the hinge. But on Jeannette’s older gates, pins that have gone through 80 winters are typically rusted solid inside the barrel. The honest fix is to torch-cut the pins, clean the hinge barrels, and weld in new pins. It’s a controlled repair, not a demolition job. We do it on site and the gate stays where it belongs.
Brands We Service in Jeannette
We carry parts and service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Jeannette’s older gates, we most commonly stock Linear and Viking operator components, plus Ghost Controls hardware for lighter residential retrofits. Most parts are on the truck, so we’re not ordering and coming back. For the full list, see our brands.
Pricing for Gate Repair in Jeannette, PA
| Service | Typical range in Jeannette |
|---|---|
| Hinge & post re-set | $235-$455 |
| Gate realignment (swing) | $120-$210 |
| Electric gate repair (operator) | $180-$390 |
| Full operator replacement | Starts around $650 |
| Weld and rust repair | $95-$250 |
| Pedestrian gate installation | $900-$2,400 |
| Single swing driveway gate (manual) | $2,400-$4,800 |
| Single slide driveway gate (manual) | $3,200-$6,200 |
| Automated driveway gate with operator | $6,000-$12,000 |
| Post reset/replacement (per post) | $700-$1,500 |
| Keypad entry system | $850-$1,600 |
| Card reader installation | $900-$1,700 |
What pushes price up in Jeannette is almost always the post work. Original alley posts were set in brick borders or shallow mortar, not concrete to frost depth, so a “simple” hinge repair often becomes a post reset once we see what’s underneath. Every price is quoted and agreed before we pick up a single tool, and that’s the number on the invoice.
Neighborhoods We Serve in Jeannette
We work all through the 15644 zip code. Typical response for a repair call in Jeannette is same day when you call before early afternoon.
- Downtown Jeannette and the streets off Clay Avenue
- Neighborhoods east of Lowry Avenue
- Areas near Jeannette High School
- Residential blocks around the Elliott Group
- Alley-access streets throughout 15644
Service Area - Cities Near Jeannette
We serve Jeannette, PA directly, and our crews regularly work in Greensburg, PA, Murrysville, PA, White Oak, PA, Monroeville, PA, and North Versailles, PA. Dispatch and scheduling are coordinated from our Philadelphia office; crews serve Jeannette locally. No trip charge inside the county.
Serving Jeannette, PA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Jeannette and the communities around it; dispatch is coordinated from our Philadelphia office. The map shows the Jeannette coverage area; if your address is on it, we can help.
Also serving nearby: Jeannette, PA, Greensburg, PA, Murrysville, PA, White Oak, PA, Monroeville, PA, North Versailles, PA.
FAQs About Gate Repair in Jeannette
For repair calls, same-day response is typical when you call before early afternoon. Calls are answered by a live person 24 hours a day, and we’ll give you a real arrival window, not a four-hour guess. If it’s an emergency, we’ll get there as fast as we can and tell you exactly when to expect us.
Most gate repairs don’t require a permit in Jeannette, but new installations and any work that changes the fence line or adds automation may need Westmoreland County approval. We know the local requirements and will tell you straight if your job needs paperwork before we start. We don’t begin work that requires a permit without confirming it’s in order.
We serve the full Jeannette area and surrounding Westmoreland County communities. If you’re close to the city line, call us and we’ll confirm coverage. There’s no trip charge inside the county, so you won’t pay extra for being on the edge of the service area.
Call (877) 610-2993 for a free estimate on any gate work in Jeannette. You’ll reach a live person, not a voicemail, and we’ll quote your price upfront before any work starts. Seniors and veterans receive a permanent 10% discount, and we take $40 off any repair over $200.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Jeannette Customers Say
"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu