Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Danvers, MA
Gate repair in Danvers typically costs $180 to $340 for hinge, latch, or sensor fixes, while full motor replacements run $650 to $1,400. Most repairs in the 01923 ZIP are completed in a single visit, and a live person answers our phone around the clock at (877) 610-2993. Danvers sits where 17th- and 18th-century Colonials and Federals meet a dense Route 1 and I-95 commercial corridor, so a technician here switches between restoring hand-forged iron hinges on a 1760s estate gate and servicing high-cycle sliding operators at a warehouse, often in the same day.
Why Danvers Homes Are Different
The soil in Danvers is clay-heavy, and the full North Shore freeze-thaw cycle shoves gate posts out of plumb every winter. By spring, a gate that closed perfectly in October is dragging on the latch or binding at the hinge. Salt-laden air off the Danvers River and Salem Sound also chews through ferrous hardware faster than inland towns see, so we inspect hinge pins and post anchors for corrosion even on gates that look fine at a glance.
The older homes present their own problem: original hardware is often hand-forged and non-standard, so direct replacement parts simply don’t exist. We’ve fabricated hinge straps on site to match 18th-century ironwork on properties off High Street and Centre Street. On the other end of town, the Avalon at Danvers complex on Kirkbride Drive concentrates automated residential entry gates in one dense community on Hathorne Hill, a concentration of gated-community service calls with no equivalent in any neighboring town.
Gate Repair in Danvers
Gate repair in Danvers runs $185 to $380 for most hinge, post, and realignment work, and we can usually get to your property the same day you call. If you’re on Hathorne Hill near the old State Hospital grounds with a solar opener that’s gone dark, or on Hobart Street where a Colonial-era iron gate has pulled its post out of plumb, we know exactly what you’re dealing with. Our Gate Repair crew handles everything from hand-forged hinge restoration to commercial operator overhaul.
Hinge & Post Repair
Hinge and post repair in Danvers runs $185 to $310 for most residential gates. This is the work we do more than anything else, because Danvers has a problem no neighboring town shares. The historic homes near downtown, many dating to the 1700s, sit on original hand-forged hinges and posts set directly into clay. Every freeze-thaw cycle rocks those posts a little further out of plumb. We reset the footing, sometimes with a larger concrete collar for stability, and rebuild or reproduce the hinge hardware so you keep the period look.
Electric Gate Repair
Electric gate repair in Danvers typically runs $220 to $340 when the problem is a control board, limit switch, or wiring fault. We service Linear, Viking, Ghost Controls, and DoorKing operators, and we keep common boards and remotes in the truck so we’re not waiting on a parts shipment. The salt air near the Danvers River corrodes low-voltage connections faster than inland towns, so we seal and protect every splice we touch.
Gate Realignment
Gate realignment in Danvers runs $160 to $280 when it’s a straightforward adjustment, and more when the post itself needs resetting. After a Danvers winter, half the swing gates in the 01923 ZIP are binding or dragging because the ground moved under the posts. We square the frame, reset the hinge pins, and adjust the latch so the gate closes true. Then we’ll show you what we did and why it should hold through next spring’s thaw.
Why do my Danvers gate posts shift out of alignment every spring, and can you fix it permanently?
Your gate posts shift because Danvers sits on clay-heavy soils that expand when frozen and contract when thawed, pushing shallow-set posts out of plumb over a single winter. We fix it permanently by resetting the post in a deeper footing, often with a wider concrete collar that spreads the load and resists heave. On historic properties we match the original hardware so the repair doesn’t look like a patch job. Call (877) 610-2993 for a free look.
Can you repair a hand-forged iron gate hinge on a historic Colonial home in Danvers without replacing the gate?
Yes, and that’s exactly the kind of work we do most often in Danvers’s historic district. We rebuild or reproduce the hinge pin and strap to match the period hardware, weld on site if needed, and leave the original gate in place. Replacing an 18th-century gate with a modern one would be a loss to the property. We’d rather fix the hinge correctly than sell you a gate you don’t need. Call (877) 610-2993.
Gate Installation in Danvers
Gate installation in Danvers means working with historic homes on one street and high-cycle commercial gates two miles away on Route 1. A new driveway gate in Danvers typically runs $2,800 to $7,500 installed, depending on the material, operator, and site conditions. We get that dual demand, because we’ve been doing it since 2001. Our Gate Installation work covers everything from period-appropriate estate gates to warehouse security slides.
Sliding Gate Installation
Sliding gates are the workhorse in Danvers, especially on shared driveways in the historic core where a swing gate physically can’t open without hitting a neighbor’s fence or blocking the street. We install cantilever slide gates, V-track slides, and rear-mounted operators that work in tight quarters. On a shared driveway off High Street, we replaced a sagging double swing gate on a 1740s Colonial that couldn’t open without dragging on the stone apron. A sliding gate installation in Danvers runs $4,000 to $7,500 because of the track, the motor, and the extra steel.
Swing Gate Installation
Most single-family homes in Danvers with the room for it get a swing gate. They’re quieter than slide gates and look right on the postwar Cape Cods and ranch subdivisions from the 1950s through the 1970s. We weld the frame on site when it’s steel, or hang and adjust aluminum and wood gates with hinges sized for the post, not the other way around. A single swing gate in Danvers typically runs $2,800 to $5,500 installed, including the operator and standard hardware. The critical part in Danvers is the post: clay-heavy soil heaves every winter, and a post installed without deep enough concrete and proper drainage will lean within two seasons.
Pedestrian Gate Installation
Pedestrian gates in Danvers run small and specific: a wrought-iron walk gate next to the driveway, a locked entry gate at a condo building, a wooden gate between a house and the side yard. These jobs look simple and they’re the ones where we see the most sloppy work left behind by somebody in a hurry. A pedestrian gate still needs its post set deep, still needs hinges that match the weight, still needs the latch to catch true. Pedestrian gates run $900 to $2,800 in Danvers.
Can you install a sliding gate on a shared driveway in Danvers where there is no room for a swing gate?
Yes. Sliding gates are the practical answer for most shared driveways in Danvers, especially in the historic core where swing gates can’t open without crossing a property line or blocking the street. We install cantilever and V-track slides with rear-mounted operators so we don’t have to trench across the driveway, and we use free-exit probes instead of loop detectors when there’s no room to cut. Both neighboring homes keep full access. Call (877) 610-2993 for a site visit.
How do you keep a new gate working on a Danvers historic home with original hand-forged hinges?
We fabricate. Original 18th-century hinges on a 1740s Colonial off High Street aren’t a catalog part. Our crew welds sleeves, collars, and new strap hinges on site to match the original hardware, and we set new posts below the frost line so the gate hangs true through a Danvers winter. The goal is to keep the historic look and make the hardware structurally sound, not swap iron for a box-store replacement. Call (877) 610-2993.
Gate Motor & Opener in Danvers
Gate motor repair and opener installation in Danvers is work we do every week, from the tight shared driveways off Maple Street to the rolling gates on Route 1’s commercial corridor. When your gate stops responding to the remote or starts grinding halfway open, you need someone who knows this town’s specific problems: clay-heavy soil that heaves posts out of plumb, salt air off Salem Sound that eats rack and pinion components, and narrow rights-of-way where a swing gate simply won’t work. Our Gate Motor & Opener service covers diagnosis, repair, and full replacement.
Motor Repair
Most Danvers gate motor failures we see trace back to two local culprits: freeze-thaw heave and salt corrosion. A motor that worked fine in November starts tripping overload sensors by March because the hinge post shifted a quarter inch and bound the operator. A standard gate motor repair in Danvers typically runs $180 to $340, including the service trip inside Essex County and the labor to diagnose and fix the issue. We diagnose the whole system before replacing parts. On a recent Page Street job, what looked like a dead keypad entry turned out to be gravity: the post had heaved out of plumb, binding the rack and pinion opener and tripping the safety photocell. We reset the post and saved the motor.
Linear Motor Installation
Linear operators are the go-to for slide gates on Danvers commercial properties and tight residential rights-of-way, where there’s no room for a swing arc. A linear motor mounts along the gate’s frame and pulls it level along the track without the torque of a rotary drive. That means fewer stripped gears, which matters in Danvers because salt-laden air from the Danvers River accelerates wear on exposed rack and pinion parts faster than inland towns like Middleton see. Slide motor installation on a new track runs $1,400 to $2,300 in Danvers.
Intercom Integration
New opener installation in Danvers often means working around existing pillars, grade changes, and access that has to keep flowing. We install operators wired for a vehicle loop detector, a keypad, and a safety edge from the start, because adding those later costs more and tears up the drive. Intercom integration with keypad and loop detector adds $400 to $800 to a Danvers job. Every installation gets upfront pricing agreed before any work starts.
Why do gate motors on Danvers properties fail most often in spring?
Gate motors in Danvers fail most in spring because winter freeze-thaw cycles in our clay-heavy soil shift hinge posts out of alignment, which binds the motor and trips overload sensors. By March and April, all that movement from December through February has pushed posts far enough that motors start stalling, grinding, or refusing to move. Most spring failures are alignment problems, not dead motors, which is why we check post plumb before quoting a motor replacement. Call (877) 610-2993.
Can a slide gate motor be installed on a narrow shared driveway in Danvers?
Yes, and in Danvers it’s often the only practical option. Many shared driveways along rights-of-way off Centre Street and Maple Street don’t have the setback for a swing gate arc, so we install a slide motor that pulls the gate parallel to the drive line. The key is precise post footing placement and a linear motor aligned to the track so the gate doesn’t bind when the soil shifts. We’ve done this dozens of times in the 01923 ZIP. Call (877) 610-2993.
Gate Access Control in Danvers
Gate access control in Danvers runs about $450 to $1,800 for most residential keypad and intercom jobs, and $1,200 to $4,500 for full video intercom or solar-powered systems on long rural driveways. We’re Gatewood Fence & Gate, and Hal Gatewood has been fixing gates and entry systems since 2001. He answers the phone himself, 24/7, at (877) 610-2993. If your keypad quit at the Avalon complex on Kirkbride Drive or your estate gate near the Danvers River won’t read remotes, we know the property and the hardware. Our Gate Access Control work covers everything from simple keypad swaps to full smart-entry retrofits.
Keypad Entry
A keypad is the simplest access control there is, and in Danvers it fails in predictable ways. Salt air off Salem Sound eats the brass contacts inside the keypad housing over three or four winters. By the second spring, the buttons get intermittent. We stock weather-sealed keypad replacements and can usually swap one out same day. Keypad entry in Danvers runs $180 to $600 installed. On the older Colonial properties near Centre Street, we wire keypads to work with existing wrought-iron post hardware so the look doesn’t change.
Video Intercom
Video intercom is the biggest upgrade Danvers homeowners ask for, especially on the older estate properties where you can’t see the gate from the house. A video intercom lets you see who’s there before you open. On a Colonial-era property with an antique iron gate, we retrofit the camera and intercom into the existing post cap or a discrete bracket that doesn’t alter the gate’s appearance. A full video intercom with a camera, indoor monitor, and wiring runs $1,200 to $3,200 in Danvers.
Solar Gate Opener
A lot of Danvers acreage entrances are too far from house power to trench conduit. Solar gate openers solve that. We install and service solar-powered operators for long driveways off Route 1 and rural lots on the north side of town. The key is sizing the panel and battery to the duty cycle, not just the gate weight. Solar gate opener installations for long Danvers driveways run $2,800 to $4,800 depending on gate width and duty cycle. Undersize the battery and you’ll have a dead gate every cloudy week in January. We don’t let that happen.
Can I add a solar gate opener for a long driveway off Route 1 where there’s no power at the entrance?
Yes. We install solar gate openers sized to the gate’s weight and daily cycle count, not just a generic panel. For long Danvers driveways off Route 1 where trenching conduit would mean hundreds of feet of digging, solar is often the cheaper and more reliable option. The critical part is the battery bank and a panel large enough to recover from cloudy winter weeks. We quote the full system, installed, before any work starts. Call (877) 610-2993.
The keypad at my gate works fine in summer but fails when it gets cold-what’s happening?
Cold-weather keypad failure is usually a failed heating element inside the enclosure or condensation that freezes across the contact points at night. Danvers salt air speeds up the corrosion that causes both. We replace the keypad or the enclosure heating strip, and we use weather-sealed units that hold up better near the coast. If it’s a Viking, DoorKing, or Elite keypad, we likely have the replacement on hand. Call (877) 610-2993.
Gate Parts & Welding in Danvers
Gate parts and welding in Danvers usually comes down to one of two situations: an ornamental iron gate on a historic Colonial that’s sagging off its hinges, or a commercial rolling gate along Route 1 that’s cycling hundreds of times a day and wearing through rollers. We handle both, often in the same afternoon. Hal Gatewood has been fixing gates since 2001, and our crew works on the full range: hand-forged hinge repairs on 1700s ironwork to rack replacement on warehouse slides. Our Gate Parts & Welding keeps gates in your driveway, not on a shop truck.
Hinge Replacement
Hinge replacement in Danvers often means working with hardware that’s older than the United States. The historic core has Colonial and Federal properties with hand-forged iron hinges you won’t find in any catalog. Direct-replacement parts simply don’t exist for a lot of these gates. So we fabricate them on site, matching the original profile and welding new material to what’s salvageable. Hinge replacement runs $180 to $340 for standard weld-on or bolt-on hinges on residential gates. Hand-forged custom fabrication on historic ironwork runs higher, typically $400 to $800 depending on the profile and finish work.
Post Replacement
Danvers sits on clay-heavy soil that freezes and heaves every winter. That ground movement knocks gate posts out of plumb on a regular basis, especially on ornamental estate gates with heavy masonry pillars. When a post goes, the gate binds, the latch misaligns, and the operator starts fighting the load. We excavate the old footing, pour a new one at proper depth for the soil conditions, set the post to plumb, and re-hang the gate. Post replacement runs $350 to $750 for a standard steel or wood post with new footing, including re-hanging the gate. Fix the panel without the post and you’ll fix it twice. We’d rather fix it once.
Custom Welding
Custom welding is where we do some of our best work in Danvers. Historic properties around the town center often have ornamental gates that were built by hand and can’t be replaced with anything off a shelf. We weld on site, in the driveway, so the gate never leaves the property. Rail repair and welding runs $150 to $400 for crack repair, reinforcement, or straightening on residential gates. Custom scrollwork or ornamental fabrication starts around $450 and goes up with complexity. That means we can match the hand-forged profile of an 1800s hinge strap, repair a broken scroll, or fabricate a new section that blends with the original ironwork. The homeowner gets their gate back without hauling it off.
Why does my Danvers gate keep sagging every spring even after I adjust the hinges?
Your gate is probably sagging because the hinge post, not the hinge itself, is being pushed out of plumb by the freeze-thaw cycle in Danvers’s clay-heavy soil. Ground heave shifts the post every winter, and adjusting the hinges without fixing the post only buys you a few weeks. We excavate and replace the post footing, set the post to plumb, and then re-hang the gate so it doesn’t sag again next spring. Call (877) 610-2993.
Can you match the original hand-forged hinges on my 1700s Colonial gate in Danvers?
Yes, we fabricate and weld replacement hinge straps on site to match the hand-forged profile of your original hardware. Direct-replacement parts don’t exist for most 18th-century Danvers ironwork, so we build new material that matches what’s there and weld it in without hauling the gate off the property. Our custom welding on historic gates is one of the things we do most in the 01923. Call (877) 610-2993 for a free look.
Brands We Service in Danvers
We carry parts and stock common boards for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Danvers properties near the water, we keep marine-grade racks and sealed enclosures on hand because salt air doesn’t wait for a parts order. Most brand-specific repairs in the 01923 ZIP are done same day. See all brands we service.
Pricing for Gate Repair in Danvers, MA
| Service | Typical range in Danvers |
|---|---|
| Hinge & post repair | $185 - $310 |
| Gate realignment | $160 - $280 |
| Electric gate repair | $220 - $340 |
| Automatic gate repair | $220 - $380 |
| Weld & rust repair | $150 - $400 |
| Gate motor repair | $180 - $340 |
| Gate motor replacement | $650 - $1,400 |
| Single swing gate installation | $2,800 - $5,500 |
| Sliding gate installation | $4,000 - $7,500 |
| Pedestrian gate installation | $900 - $2,800 |
| Keypad entry installation | $180 - $600 |
| Video intercom system | $1,200 - $3,200 |
What pushes price up in Danvers: historic hardware that needs custom fabrication, masonry pillar reset instead of steel post replacement, and swing-to-slide conversions on tight rights-of-way. Every price is quoted and agreed in writing before any work starts. That’s the price you pay, not a penny more.
Neighborhoods We Serve in Danvers
We work all over the 01923 ZIP, from the historic core near downtown to the commercial corridor along Route 1. Typical response time in Danvers is same-day for repair calls, and emergency calls get answered by a live person no matter the hour.
- Danversport
- Downtown Danvers
- Hathorne Hill (Avalon at Danvers)
- Ferncroft
- Putnamville
Service Area - Cities Near Danvers
We dispatch and schedule from our Boston office, and our crews serve Danvers locally every day. We also work in Peabody, MA, Salem, MA, Beverly, MA, Beverly Cove, MA, and Middleton, MA. If you’re unsure whether your property falls inside our range, call (877) 610-2993 and we’ll tell you straight.
Serving Danvers, MA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Danvers and the communities around it; dispatch is coordinated from our Boston office. The map shows the Danvers coverage area; if your address is on it, we can help.
Also serving nearby: Danvers, MA, Peabody, MA, Salem, MA, Beverly, MA, Beverly Cove, MA, Middleton, MA.
FAQs About Gate Repair in Danvers
Most repair calls in Danvers are same-day, and our phone is answered by a live person 24 hours a day. Emergency calls, gates stuck open or won’t secure, get priority scheduling. We’ll give you a real arrival window when you call, and Hal or his crew will be there in that window.
Residential gate installation in Danvers typically doesn’t require a building permit for a standard replacement, but new automated gates with electrical work may need an electrical permit through the town. Commercial properties along Route 1 often have additional site-plan requirements. We know Danvers’s process and can tell you exactly what’s needed when we see your property. Call (877) 610-2993.
Yes, we service HOA-managed properties including the Avalon at Danvers on Kirkbride Drive. We coordinate with property managers for access, provide written estimates for board approval, and schedule work to minimize disruption to residents. Our crew knows that site’s gates and entry patterns well. Call (877) 610-2993 to arrange service.
Call (877) 610-2993 for a free estimate. A live person answers around the clock, and we’ll quote your price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Danvers Customers Say
"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo