Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Sandy Springs
Gate installation in Sandy Springs typically runs between $2,800 and $9,500 depending on whether you’re adding automation to an existing manual gate, replacing a failed builder-grade operator on a 1980s brick-pillar setup, or installing a full driveway gate from scratch. Most jobs we quote in the 30328 zip code take one to three days once materials and any required permits are in hand. Hal Gatewood has been doing this work since 2001, and he still shows up to look at the post, the conduit, and the soil before putting a number on paper. Call (877) 610-2993 and you’ll talk to a live person who can schedule a free measure at your Sandy Springs property.
Why Gatewood Fence & Gate Is Sandy Springs’s Preferred Gate Installation Company
Sandy Springs is not a place where you can fake expertise. The homes along Heards Ferry Road, Mount Vernon Road, and the Spalding Drive corridor were built to a standard that a lot of today’s national installers have never worked around. Hal started this company in 2001 servicing the exact mix of heavy wrought-iron swing gates, brick-pillar slide gates, and subdivision entrance systems that define Sandy Springs. The name is on the shop and on every invoice. You can drive to the shop and look him in the eye before you commit to a job.
We answer the phone with a live person 24 hours a day, seven days a week. Not a voicemail tree. Not a call center three states away. When a Sandy Springs customer calls because their swing gate tripped a breaker after another thunderstorm, the person who picks up knows what that means because we work those streets every week. Every installation carries our 90-Day Done Right Promise in writing. If something isn’t done right, one call brings Hal back. No runaround, no “that’s not covered.”
Crews serve Sandy Springs locally, with scheduling coordinated from our Atlanta office. That means we can be on a job site in Dunwoody in the morning and Mount Vernon Road by early afternoon without charging you for an hour of windshield time. For the larger estate gates and older subdivision entrances this page is about, we send people who have done this exact work in this exact zip code, not someone learning your gate system on the fly.
For the full scope of what we do, see our Gate Installation team details and service breakdown. And if you want to understand how we fit into the broader local market, our Gate Installation in Sandy Springs page covers the whole service area.
Our Gate Installation Services in Sandy Springs
Driveway Gate Installation
New driveway gates in Sandy Springs almost always mean one of two situations. Either you’re adding a gate where none existed, which means running power and low-voltage control wire from the house or a sub-panel, or you’re replacing a gate that’s been on the property since the home was built in the 1980s or early 1990s. In the replacement case, what you’re really replacing is often the post footing and the conduit, not just the gate leaf. We quote the whole job, not just the visible part. A new driveway gate with automation in the 30328 area typically runs $4,200 to $9,500 for a double swing or slide, including the operator, safety sensors, and the electrical run.
Pedestrian Gate Installation
A pedestrian gate in Sandy Springs is usually paired with a driveway gate on an estate property, or it’s the dedicated entry on a side yard or pool enclosure. These gates move lighter loads, but they still live in the same red clay soil and still need proper post footings. We install standalone pedestrian gates with keypad or intercom access from $1,800 to $4,000 depending on the leaf weight and whether you want it tied into a larger Sandy Springs Gate Access Control system. If you’re adding a pedestrian gate next to an existing driveway gate, doing both at once saves on the electrical rough-in and usually cuts a few hundred dollars off the total.
Sliding Gate Installation
Sliding gates are the standard for Sandy Springs properties with long driveways or limited swing clearance, and the tragic flaw is usually the operator size. Builders in the 1980s and 1990s routinely installed operator motors that were undersized for the heavy brick-pillar slide gates they were wired to. That’s why we replace so many burned-out gears and stalled motors in this area. A proper sliding gate installation in Sandy Springs runs $3,500 to $8,000, with the operator, track or cantilever hardware, safety edges, and the concrete pad for the motor included. We stock or can quickly source Gate Parts & Welding in Sandy Springs for Viking, Linear, BFT, and FAAC operators, which covers the majority of what’s still in the ground in this part of town.
Swing Gate Installation
Swing gates are the dominant style in the estate neighborhoods along Mount Vernon Road and Heards Ferry Road, and the failure mode is nearly always the hinge post, not the gate itself. A gate sags in the hinge post, not in the middle. In Sandy Springs, the expansive clay soil swells during wet winters and contracts in summer drought, and a hinge post set with a shallow footing will lean a little more every year until the gate drags and the operator overloads. We re-set posts with deeper footings, pack with gravel and concrete the right way, and install operators sized to the actual leaf weight. A single swing gate with automation runs $2,800 to $6,500 in this market. A double swing gate on brick pillars typically lands between $4,500 and $8,500.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Sandy Springs
We’re certified to service and install nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Sandy Springs specifically, the bulk of what we encounter on older estate properties is FAAC, Viking, and Linear hardware from the original construction era. We keep common replacement parts and control boards for those three brands on hand so a repair or installation doesn’t stall while we wait on a distributor. If you’re replacing an old Linear or Viking operator, we can usually re-use the existing posts and photo eyes if they’re still sound, which keeps the total cost down and the job faster.
Common Gate Installation Problems We See in Sandy Springs Homes
- Builder-grade operators undersized for the gate. During the 1980s and 1990s construction boom, many Sandy Springs homes got operators rated for far lighter gates than what was actually hung. The motor strips gears, burns capacitors, or quits entirely years before it should. We size the new operator to the real gate weight plus a margin for wind load.
- Cracked conduit and dead low-voltage runs. The original low-voltage wiring on older Sandy Springs gates was often run through thin conduit that has cracked in the red clay. After heavy spring rains, water gets in and shorts the control board. We trench new conduit, pull fresh wire, and sometimes add a surge protector at the board to handle the thunderstorms this area gets every summer.
- Leaning hinge posts from shallow footings. The red clay under Sandy Springs swells when wet and shrinks when dry. A hinge post set 18 inches deep will move. A post set 36 or 42 inches deep with a proper concrete footing holds the gate square. Fix the panel without the post and you’ll fix it twice.
- No safety sensors on older automatic gates. A surprising number of original Sandy Springs gate installs from the 1980s and 1990s were done with no photo eyes or edge sensors. Gates installed before modern UL 325 standards often fail inspection when a new operator goes in. We add safety sensors and edge protection on every automation job, and we pull the City of Sandy Springs permit so it passes the first time.
Pricing for Gate Installation in Sandy Springs, GA
Here’s what we see in the Sandy Springs market right now. A straightforward operator replacement on an existing manual or automatic swing gate runs $1,800 to $3,200. Automating a manual double swing gate that was never wired for a motor runs $3,500 to $6,500, including the trenching, conduit, operator, safety sensors, and permit. A full new sliding driveway gate with automation and a concrete motor pad runs $4,000 to $8,000. The big variables are the gate leaf weight, the distance from the house panel to the gate, and whether the existing posts can be saved or need re-footing. Every price is quoted and agreed before any work starts. You will not see a different number at the end because the number was on the paper you signed. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Sandy Springs
We work throughout Sandy Springs and the surrounding north Atlanta communities. If you’re in Dunwoody, Brookhaven, North Atlanta, or Vinings, you’re inside our normal service area and we’ll come out on the same schedule, not a “whenever we’re in your area” schedule. The same crews, the same 90-Day Done Right Promise, the same live person on the phone.
Serving Sandy Springs, GA - Our Local Coverage Area
We’re based in the Sandy Springs area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Sandy Springs
Yes. Sandy Springs has been its own city since 2005, which means gate operator replacements and any structural post work fall under City of Sandy Springs permitting, not Fulton County. This catches a lot of homeowners and out-of-area contractors off guard. We pull the correct electrical or building permit on every job we do in the 30328 zip code. Call (877) 610-2993 and we’ll get the permit process started before any work begins.
Because lightning has likely taken out the control board or the transformer, and the old wiring run through cracked conduit is letting moisture reach the low-voltage side of the system. This is a repetitive seasonal Gate Repair - Sandy Springs call, where summer storms roll through with regular lightning. We replace the damaged board, often add a surge protector, and check the conduit integrity so the next storm isn’t a repeat. Call (877) 610-2993 if your gate died after the last storm.
Yes, and it’s one of the more common jobs we do in this part of town. Many Sandy Springs estate gates from the 1980s and 1990s were installed as manual swing gates because the original owner wanted the look but not the expense of automation. Adding an operator means running power and control wire to the gate, setting a proper concrete pad or post mount for the operator, and adding safety sensors. The whole job runs $3,500 to $6,500 for a double swing gate. Call (877) 610-2993 for a free measure and written estimate.
It’s almost always a post problem. In Sandy Springs the expansive red clay swells and shrinks through the year, and a hinge post with a shallow footing will lean until the gate leaf sags and drags. We re-set the post with a deeper footing and proper drainage, then re-hang and re-align the gate. Replacing just the panel without fixing the post means you’ll do the job twice. Call (877) 610-2993 and we’ll tell you honestly whether your post can be saved.
Yes, and this matters if your gate was installed before the mid-1990s. Current UL 325 standards require photo eyes and edge sensors or an equivalent entrapment protection system on any automatic gate operator. Many original Sandy Springs installs predate those requirements, and when we replace the operator, we bring the whole system up to current code so it passes the City of Sandy Springs inspection. Call (877) 610-2993 and we’ll evaluate what your existing gate has and what it needs.
What Makes Sandy Springs Gate Installation Different
Sandy Springs incorporated as its own city in 2005, taking permitting authority away from Fulton County. For a gate installation that involves an operator replacement or structural post work, you now need a City of Sandy Springs electrical or building permit. A lot of homeowners don’t realize that until after a contractor has already started the job, and a lot of out-of-area contractors don’t bother finding out. We pull the right permit every time, because a gate that can’t pass inspection is not an installed gate, it’s a problem you now own. In the 30328 zip code specifically, the older estate and subdivision gate systems are hitting end-of-life at the same time. Sandy Springs developed rapidly through the 1980s and early 1990s as one of metro Atlanta’s most affluent unincorporated enclaves, and that produced a concentration of privately gated residential estates and subdivision entrance systems you simply don’t see at the same density in Dunwoody or Roswell. Those original gate operators, swing arms, and control boards are now 30 to 40 years old and failing in large numbers. The builder-grade operators installed at original construction were often undersized for the heavy brick-pillar slide gates they were wired to, and the low-voltage wiring run through cracked conduit in the red clay is starting to short after decades of rain. On Mount Vernon Road we replaced a builder-grade LiftMaster swing gate operator that had never been strong enough for the double wrought-iron gate it was wired to. The original install from the early 1990s had the low-voltage wire run through cracked conduit in the red clay, so we trenched new conduit, pulled fresh wiring, and set the hinge post with a deeper footing to stop the sag. We then installed a new FAAC operator with a loop detector and safety photocells, and pulled the City of Sandy Springs electrical permit before starting. That’s the difference between a local crew that works this zip code every week and someone driving up from a different county.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Sandy Springs since 2001.