Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Sandy Springs
Sandy Springs gate repair typically runs $225-$650 for most common failures, and we can usually be at your property within a few hours when a gate is stuck open, stuck closed, or grinding itself apart. We know the estates off Mount Vernon Road and the subdivisions along Spalding Drive the way only a local crew can – because we have been fixing gates here since before the city even had its own permit office. Call (877) 610-2993 and you’ll get Hal or one of his crew on the line, not a recording.
Why Gatewood Fence & Gate Is Sandy Springs’s Preferred Gate Repair Company
Hal Gatewood has been running this shop since 2001, and his name is still on the door and on every invoice. When you call about a sagging ornamental iron gate on Heards Ferry Road, the person who answers is the person accountable for the work. Sandy Springs homeowners have learned the hard way that a gate is only as good as the person who set the post – and we re-foot posts here the way the red clay demands.
Sandy Springs is its own city now, with its own permit requirements, and we pull the correct City of Sandy Springs permit on every operator replacement and structural column repair. That’s not a formality. An out-of-area contractor who is still working off Fulton County assumptions can leave you holding an unpermitted repair that bites when you sell the house. Our crew shows up uniformed and background-checked, and every job carries the 90-Day Done Right Promise in writing. Not “up to” 90 days, not “in most cases.” Ninety days, plain.
Our Gate Repair Services in Sandy Springs
Electric Gate Repair
Most electric gate failures in Sandy Springs come down to two things: lightning and age. The summer thunderstorm season hammers control boards and transformers across the area, and the original Viking and Linear boards installed on 1980s estate gates are now obsolete enough that generic replacement parts no longer exist. We source from specialty distributors who still carry what these old systems need, and we do not tell you to replace a gate when the board is the only problem.
Automatic Gate Repair
An automatic gate that jerks halfway open, reverses for no reason, or sits dead after a storm is usually not a lost cause. We service LiftMaster, FAAC, BFT, Linear, and Viking operators, among others, and we stock common parts locally so your repair does not wait on a warehouse three states away. When lightning has fried a transformer and taken the board with it, we’ll show you exactly what failed before we touch a wiring nut.
Hinge & Post Repair
This is the repair Sandy Springs needs more than any other. The red clay beneath gate posts in Georgia swells in wet winters and contracts in summer drought, and a post that moves a quarter inch becomes a gate that sags four inches within a few years. We cut out the old steel, re-foot the post in new concrete below the clay line, and weld new hinges onto solid steel instead of packing rusted brackets back into a crumbling brick column.
Gate Realignment
When a gate leaf drags on the ground or no longer lines up with the latch, the frame itself has usually shifted. We do not just lift the panel and call it square – we check the hinge posts, the rack and pinion, and the operator mount, because a gate that is realigned without fixing the post will be dragging again inside a year. On heavy custom wrought-iron gates, that means cutting and re-welding, not cranking a bolt.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Sandy Springs
The older gates across Sandy Springs run on operators that big-box stores stopped carrying years ago. We service FAAC and BFT actuators, Linear swing arms, and Viking slide operators, and we keep common boards, capacitors, and limit switches in stock for the systems we see most on Mount Vernon Road and the estate streets off Spalding Drive. If you have a Ghost Controls kit on a newer gate, we handle that too. The one thing we will not do is tell you to replace a repairable operator just because sourcing the part takes a phone call instead of a click.
Common Gate Repair Problems We See in Sandy Springs Homes
- 1980s Viking and Linear operators failing together. The original automation equipment installed during Sandy Springs’s big estate-building boom is now 30-40 years old, and we are seeing entire neighborhoods where every third gate has the same dead board. We source OEM and aftermarket parts through specialty distributors who still serve these systems.
- Lightning damage to control boards and transformers. Summer thunderstorms roll through Sandy Springs with enough frequency that we keep spare FAAC and BFT boards on the truck from April through September. A strike does not even need to hit your gate directly; a near miss on the power line is enough.
- Post lean from Georgia red clay movement. The expansive soil under Sandy Springs swells in wet winters and shrinks in summer drought, and every cycle works the post a little further out of plumb. Once a post leans, every other component starts wearing faster.
- Corroded steel hinges packed into original brick columns. The iron on a 1980s ornamental gate might still look decent, but the steel hinge embedded in the brick is often rusted through. We replace these with new steel set in proper footing, not with a patch job that reproduces the same failure.
Pricing for Gate Repair in Sandy Springs, GA
Here is what we quote for common repairs in Sandy Springs. Electric gate board replacement runs $250-$480 depending on the board, and a full operator swap on an estate gate is typically $900-$1,600 with the motor and arms. Hinge and post repair, including re-footing a single post, runs $350-$800. Gate realignment without structural work is $150-$300. Gate Repair estimates are free, the price is agreed before we start, and there is no trip charge anywhere in Fulton County. You also get $40 off any repair over $200, and seniors and veterans always get 10% off. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Sandy Springs
If you are just over the line in Dunwoody, Brookhaven, North Atlanta, or Vinings, we work there every week. The same crew that repairs gates across Sandy Springs covers the surrounding area, and the same 90-Day Done Right Promise applies. Call ahead and we will give you a straight answer on timing before you have to ask twice.
Serving Sandy Springs, GA - Our Local Coverage Area
We’re based in the Sandy Springs area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Sandy Springs
Yes. Since Sandy Springs incorporated in 2005 and took over permitting from Fulton County, an operator replacement that involves the electrical feed, and any structural work on a column or post, requires a City of Sandy Springs permit. We pull the correct permit on every job that calls for one, so your repair is documented and legal if you ever sell.
The Georgia red clay beneath the posts is the main culprit. It swells when the ground is wet and contracts in summer drought, which slowly works even a properly set post out of level. Once the post moves, the hinge geometry changes and the entire gate leaf starts to bind and wear. Re-footing the post below the clay line is the only repair that lasts.
On most Sandy Springs slide gates we see, the grinding is coming from a worn rack and pinion or a set of rollers that have flattened over years of use. The motor is usually fine but working against a drive train that is binding. We inspect the rack teeth, rollers, and limit switches before we ever point at the operator.
Any automatic gate installed or substantially modified in Sandy Springs has to meet UL 325 safety standards, which means proper photo sensors, reversing edges, and force settings that trip before the gate can hurt someone. If your gate keeps running after hitting an obstruction, or if the sensors are missing, that is a safety failure. A trained professional should check it before someone gets pinned.
We can source most Viking and Linear parts through specialty distributors we have bought from for years, and we will always try the repair before quoting you a full replacement. When a part is truly gone and a retrofit makes more sense, we will install a modern FAAC or BFT operator and wire it to your existing gate. Call (877) 610-2993 for an honest assessment, free of charge.
Heavy Gates, Bespoke Hardware, and the Precision Sandy Springs Estates Demand
Sandy Springs developed as metro Atlanta’s premier affluent unincorporated enclave, and one result is the highest concentration of privately gated residential estates and subdivision entrance systems in the whole metro. The custom fabricated gates along Heards Ferry Road and Mount Vernon Road are not off-the-shelf panels from a catalog; they are heavy, hand-welded wrought iron with underground operators, matched intercom and camera entry, and brick-pillar slide gates that weigh more than a small car. That kind of gate does not tolerate sloppy alignment or a motor that is undersized for the load. We weld on site in your driveway so the gate never leaves your property, and we rebuild drives so a heavy gate runs quietly instead of straining against its own hardware.
A Field Note from Heards Ferry Road
We recently reset the hinge post on a custom wrought-iron swing gate off Heards Ferry Road – the original 1987 Viking operator had corroded steel hinges packed into the brick column, and the gate was sagging 4 inches out of level. Our crew pulled the Sandy Springs permit, re-footed the post in new concrete below the red clay line, and rebuilt the rack and pinion drive so the gate runs silent without stressing the motor. That is the difference between patching a symptom and fixing the thing that caused it. Show me the gate closing on its own and I’ll show you where it’s failing – and that is where we start.
Call Gatewood Fence & Gate for Gate Repair in Sandy Springs
The name is on the shop, and the shop is down the road. Call (877) 610-2993 and a live person answers, 24 hours a day, 7 days a week. We will quote you a fair number before any work starts, pull whatever permit your job needs, and back the repair with the 90-Day Done Right Promise in writing. You can drive to the shop and look Hal in the eye if you want to – that is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Sandy Springs since 2001.