Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Frisco
Gate installation in Frisco typically runs $1,800 to $6,500 for a standard ornamental iron driveway gate with manual hardware, and $3,200 to $9,000 when you add an automatic operator, conduit runs, and safety photocells. Most of the gates we install in Frisco go into HOA-governed master-planned subdivisions where the design specs were locked in years ago, so matching the existing style matters as much as the hardware itself. We show up when we say we will, quote the price before any work starts, and stand behind every gate we hang with the 90-Day Done Right Promise in writing. If you’re in the 75034, 75035, or 75033 zip codes, call (877) 610-2993 and you’ll get a live person, not a voicemail tree.
Why Gatewood Fence & Gate Is Frisco’s Preferred Gate Installation Company
Hal Gatewood started this shop in 2001, and his name is still on the door and on every invoice. That matters in Frisco, where homeowners have been burned by companies that quote one number on the phone and show up with a different one at the driveway. Our crew works across Frisco weekly, from the newer builds along Eldorado Parkway to the established subdivisions west of the Dallas North Tollway, and we know which communities share the same gate models and HOA color codes without having to ask twice.
We’re local, owner-operated, and licensed, with a published address you can drive to and a phone number that rings to a person around the clock. The difference shows in the small things: we pre-map subdivisions in the 75034 and 75035 corridors, we stock matching ornamental iron components so a single truck can service several homes on one street, and we never say “we’ll get back to you” when you call about a gate that won’t close. Frisco homeowners keep our number because when something goes wrong with an installation, one call brings Hal back. That’s the 90-Day Done Right Promise, and it’s stamped on every job we do in Frisco.
Our Gate Installation Services in Frisco
Driveway Gate Installation
Driveway gates in Frisco are almost always ornamental iron or aluminum, and in most of the master-planned communities they were installed to satisfy HOA design requirements rather than as a homeowner upgrade. That means style, weight, and swing radius are often nearly identical across a whole subdivision. We install new driveway gates that match the existing look of your neighborhood, and we handle the full scope: posts set in concrete, gate fabricated or spec-matched, hinges rated for the gate weight, and latches that close square and stay closed. In Frisco’s Blackland Prairie clay, we over-dig and set posts deeper than code minimums because the soil moves and a shallow post will lean within two seasons.
Pedestrian Gate Installation
Side yard and pedestrian gates take more abuse than driveway gates because they get opened and closed by hand dozens of times a day. In Frisco, the 5-foot ornamental iron pedestrian gates common in 75034 and 75035 neighborhoods are often the same builder-grade units installed 15 to 20 years ago, and the hinge posts have taken years of clay heave and summer drought shrinkage. We install new pedestrian gates with commercial-grade barrel hinges, proper post footings, and self-closing hardware when HOA or pool code requires it. If your walk gate drags on the ground or won’t latch, we’ll fix the post, not just the panel.
Sliding Gate Installation
Sliding gates are less common in Frisco’s residential neighborhoods, but they show up on larger lots, side-load garages, and any property where a swing gate would eat too much driveway real estate. A sliding gate lives and dies by its track and its rollers, and in Frisco the clay soil fines up against the track and grinds rollers down faster than you’d expect. We install cantilever and track-style sliding gates with the right roller bearings for the gate weight, set the guide posts deep, and make sure the gate travels true before we call the job done. For double-wide driveway entries where swing gates would crowd the front walk, a sliding gate is often the better call.
Swing Gate Installation
Swing gates are the standard in Frisco, and most of them are double gates on ornamental iron frames with either a center latch or an automatic operator on each leaf. The single most common installation mistake we see is hanging a heavy swing gate on residential-grade hinges and a post that was never set for lateral load. In Frisco’s clay, that post moves within a year and the gate starts dragging. We install swing gates with reinforced steel posts, welded hinge mounts, and positive stops so the gate never over-travels into a brick column or a landscaped bed. Double gates need a center drop rod or an electric lock if you’re adding automation, and we handle both.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Frisco
We’re certified to service and install nine major gate brands, and in Frisco that matters because the mid-2000s construction boom left a lot of Viking, Ghost Controls, and early LiftMaster residential operators in the ground. When a Viking operator from 2006 finally gives out in a 75035 subdivision, we can replace it with a spec-matched LiftMaster unit that fits the same gate weight, the same swing radius, and the same HOA-approved profile. We stock local parts for the brands Frisco homes actually have, so your install does not stall waiting on a backordered board from a distributor three time zones away. DoorKing and Linear parts, along with Ghost Controls and Viking hardware, are on our truck or one day out for most Frisco calls.
Common Gate Installation Problems We See in Frisco Homes
- Builder-grade operators past their rated cycle life. The mid-2000s Viking and US Automatic units installed during Frisco’s housing surge were rated for a finite number of open-close cycles, and many of them hit that ceiling around 2023. When one fails, HOA rules mean the replacement has to match the original gate’s weight and swing spec, so a generic big-box operator won’t pass review.
- Posts thrown out of plumb by Blackland Prairie clay. Frisco’s soil expands in spring rains and shrinks in summer drought, and a gate post set at a standard 2-foot depth will lean within a few seasons. A new operator mounted to a leaning post will bind, strain, and burn out its motor windings in months. We set posts deeper and use concrete collars sized for the clay’s movement.
- Manual gates that were never wired for automation. A lot of newer Frisco homes have ornamental driveway gates that satisfy HOA design rules but were never given conduit, power runs, or a place for an operator. Adding automation later means trenching across the driveway approach, and that’s work we quote honestly before we start, not after.
- Powder-coat and hardware failure from the Frisco sun. Summers here regularly pass 105°F, and that UV load breaks down powder-coat finishes and degrades the plastic gears inside operator housings. We see gates in 75034 and 75035 where the iron is structurally fine but the finish is chalked and the operator’s internal gears have turned brittle. We install new gates and hardware rated for North Texas sun, not coastal mildness.
Pricing for Gate Installation in Frisco, TX
Here’s what we see in Frisco, honestly. A single manual ornamental iron driveway gate hung on new posts runs $1,800 to $4,200 depending on gate width, post size, and whether we need to remove an old concrete footing. A double swing gate with a center latch starts around $3,000 and goes up with automation. Adding an automatic operator to an existing gate runs $1,400 to $3,000, and that includes new safety photocells and a keypad. If no conduit is in the ground, plan for $800 to $2,200 more for the trench and power run, depending on distance and what’s under the path. A full new automatic sliding gate for a wide driveway starts around $4,500 and runs to $8,000 or more for a heavy ornamental iron gate. Every quote is written, itemized, and agreed to before we start work, and you’ll never see a number change at the door. Call (877) 610-2993 and we’ll come measure, look at your HOA specs, and put a price in writing free of charge.
We Also Serve Cities Near Frisco
If you’re just outside Frisco, our Gate Installation crew covers Prosper, The Colony, Little Elm, and Celina as well. The soil, the housing stock, and the HOA situations are similar, and we stock the same parts. Our Frisco page covers the specifics of the 75034, 75035, and 75033 corridors, but if you’re a few miles north or west, the same crew and the same 90-Day Done Right Promise apply.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Frisco
Yes, we match HOA-required ornamental iron gate styles every week in Frisco. We photograph your existing gate, pull the design elements that the HOA locked in (picket spacing, top rail profile, color code, height), and fabricate or order a gate that meets the same spec. In neighborhoods across 75034 and 75035, many homes share the same original gate style, so we often know the spec before we arrive. We’ll also handle the HOA paperwork if your community requires an application. Call (877) 610-2993 and we’ll start with a free measure and a look at your governing docs.
Yes, we do it regularly in Frisco’s newer subdivisions. If the builder installed a manual gate to satisfy HOA design rules but never pulled conduit for power, we trench a new line from your panel to the gate location, set the operator pad, and install the operator, photocells, and keypad. The trench and power run adds cost, but we quote it upfront and in writing before we start. In 75035 specifically, many of the manual gates we see are 16-foot ornamental iron swing gates, which means we’ll also verify that the existing posts are deep enough to carry an automated load before we mount anything. Call (877) 610-2993 for a written quote.
Frisco sits on Blackland Prairie clay, which expands during spring rains and shrinks during summer droughts, and that repeated movement gradually tilts gate posts out of plumb. A post set at a shallow depth with a small concrete collar will lean within a season or two, and once it leans, the gate drags and the operator strains. We fix it by removing the post, over-digging the hole, setting a deeper post with a larger concrete footing, and sometimes adding a steel sleeve or a second anchor point. Then we realign the gate so it closes square before we remount any operator. Call (877) 610-2993 and we’ll come take a look.
Yes, and this is one of our bread-and-butter calls in Frisco. The mid-2000s Viking operators installed during the construction surge are now past their rated cycle life, and many HOAs require the replacement to match the original gate’s weight rating, swing radius, and enclosure profile. We spec-match a LiftMaster residential operator that fits those parameters, and we document the spec for your HOA if they ask for it. We also check the hinge posts at the same time, because a new operator on a clay-leaned post will bind and fail early. Call (877) 610-2993 and we’ll get the right unit ordered and scheduled.
We do. Double-wide driveways in Frisco, particularly on larger lots and side-load garages, are one of the places where a sliding gate makes more sense than a pair of swing gates. We install cantilever and track-style sliding gates with the correct roller bearings for the gate weight, and we set the guide posts deep enough for Frisco’s clay movement. We handle the full scope including the operator, safety edges, photocells, and any power or conduit work. Sliding gates are a bigger job than a swing gate, so we quote them after a free site measure, never over the phone. Call (877) 610-2993 to schedule one.
If you need gate installation in Frisco, we’re the local shop that answers the phone, shows up in the window we promised, and puts the price in writing before any work begins. Call (877) 610-2993 for a free estimate, or drive to the shop and talk to Hal directly. His name is on the door, and it’s been there since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Frisco since 2001.