Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Benbrook
Gate installation in Benbrook usually means one of two very different jobs: a heavy ranch gate on an equestrian lot off Old Granbury Road, or an ornamental iron driveway gate on a lakefront street near Benbrook Lake. Sometimes both on the same afternoon. A typical Benbrook gate installation runs $2,200 to $6,800 depending on material, automation, and what kind of post footing the ground actually needs. Call (877) 610-2993 and a live person answers, day or night. Not a voicemail tree, not a chatbot. Hal Gatewood started this shop in 2001 and his name is still on it.
Why Gatewood Fence & Gate Is Benbrook’s Preferred Gate Installation Company
Benbrook isn’t a generic Fort Worth suburb and we don’t treat it like one. The housing stock turns on a dime here. One street off Winscott Road has 1970s brick ranch homes with original wooden gates, and half a mile toward the lake you’ll find gated entries on properties with horse stalls out back. You learn that only by driving it. Hal has been running crews through Benbrook’s streets for over two decades, and the person who shows up to your house is someone whose work you’ll see again at the grocery store. That matters when a gate operator fails at 11 p.m. and you need someone who knows which streets flood and which gates back up to Corps-managed lake levels.
Our Benbrook customers call us for one honest reason first: we fix before we replace. If a post is heaving, we fix the footing. If a control board can be repaired, we repair it. But when a gate is too far gone, we say so plainly and install something that will survive this soil. The 90-Day Done Right Promise is in writing on every Benbrook job. If it isn’t right, Hal comes back. No runaround.
Our Gate Installation Services in Benbrook
Driveway Gate Installation
Benbrook driveway gate projects split between two worlds. Older ranch homes near the lake want ornamental iron with automation, while equestrian properties further out need a heavy manual gate that a truck can pull through without hanging up. We build both, and we size the post footing for what’s actually underneath. Not a generic 24-inch concrete pour. Benbrook’s clay moves, and a driveway gate post set shallow will lean within two wet-dry cycles. We dig deeper, use more steel, and set the hinge geometry so the gate stays plumb through July drought and April rain.
Swing Gate Installation
Swing gates are the most common Benbrook installation and the most commonly botched one. A double swing gate needs a center latch that actually aligns, hinges rated for the full leaf weight, and a post that won’t walk. On Lakeway Drive and other lake-adjacent streets, we reconstruct the hinge post with an oversized footing because the soil moisture near Benbrook Lake guarantees movement. For automated swing gates we fit operators from brands like Viking, Ghost Controls, and Elite, and we route the power and safety edges to meet current standards. Most older Benbrook swing gates don’t meet them.
Sliding Gate Installation
A slide gate is usually the better answer for a long driveway in Benbrook, especially where the grade slopes toward the lake or where a swing would block the turn radius. Slide gates need a steel track, a roller assembly that holds up to North Texas heat, and cantilever builds where gravel and clay dust would clog a bottom track. We stock parts locally for DoorKing and Elite slide operators and we don’t make you wait on a backorder from a warehouse three states away. If we can’t get it at our shop, we tell you when, specifically, it will arrive.
Pedestrian Gate Installation
Pedestrian gates in Benbrook get more weather punishment than the driveway gates they sit beside. They’re used daily, slammed, kicked shut, and built with lighter hardware. A pedestrian gate on a 1990s brick ranch off Chapin Road is usually original, rusted, and sagging. Replacing just the hinges rarely buys more than a year. We build pedestrian gates with a welded steel frame and hang them on a post we already know will shift, so we engineer for it. That means deeper footings on the latch side and a slam post that stays true.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Benbrook
We install and service more than a dozen operator brands, and Benbrook’s mix of older and newer systems means we stock parts for the ones that actually fail here. Viking and Ghost Controls operators are common on Benbrook’s high-end lakefront gates. DoorKing and Elite show up on larger estate entries and some commercial access points. We keep common control boards, receiver modules, and safety edge components on hand so a Monday breakdown doesn’t become a Thursday repair. If we have to order a board, we’ll tell you the actual lead time, not a vague “about a week.”
Common Gate Installation Problems We See in Benbrook Homes
- Lakefront post heave. On streets backing up to Benbrook Lake, gate posts set in concrete heave and lean within two or three seasons. The Corps-managed lake levels swing soil moisture wildly, and the clay beneath responds by moving. Any new install near the lake needs a deeper, wider footing or it fails early.
- Obsolete 1990s control boards. Ornamental iron gates installed in the 1990s and 2000s are now hitting end-of-life on their original motors and boards. Failures show up in Benbrook’s humid summers, when heat and moisture push aging capacitors past their limit. Retrofitting a modern operator onto an existing steel frame is often cheaper than a full tear-out.
- Equestrian gate sag. Pipe-panel and tube-steel ranch gates on Benbrook acreage lots sag hard at the latch end after years of livestock pressure and wind load. The hinge post usually wasn’t set deep enough for the gate’s actual weight. Welding on a new hinge sleeve and resetting the post beats replacing the whole gate in most cases.
- Original 1970s and 1980s wooden gates. Benbrook’s brick ranch homes often still have their original wood driveway gates. The hinge posts are rotten at grade, the hardware is rusted solid, and the gate has sagged into the grass. By the time you’re re-hanging it every spring, a welded steel replacement is the cheaper option.
Pricing for Gate Installation in Benbrook, TX
We Also Serve Cities Near Benbrook
If you’re outside Benbrook proper, we run crews across the whole corner of Tarrant County. That includes Gate Installation jobs in White Settlement, Crowley, Fort Worth, and River Oaks. If you’re not sure whether your property is inside our service area around Benbrook, call us. The person answering knows the map, not just a script.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and offer Gate Repair - Benbrook because we know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Benbrook
Why do gate posts near Benbrook Lake lean so quickly after installation?
The clay along Benbrook Lake’s shoreline swells and shrinks faster than almost anywhere else in Tarrant County, and lake-level management by the Army Corps keeps that soil moisture swinging. A gate post set in a standard footing will get worked loose by one wet spring and one dry summer. The fix is engineering, not luck: deeper footings, more concrete mass, and sometimes a helical pier on the hinge side. If a company quotes you a lakefront gate without asking about your exact lot drainage, that gate will lean within two seasons. Call (877) 610-2993 and we’ll look at your site before we quote anything.
Can you retrofit a modern safety system onto my 1990s iron gate in Benbrook?
Almost always, yes. A 1990s ornate iron frame is usually still sound; the operator and control board are what fail. We replace the old board with a modern unit, add a current UL-rated safety loop or photocell, and build a proper stop on both ends of travel. Depending on the frame, we’ll also add a center stop for a double gate and new hinge bushings. The cost starts around $1,100 for a board and safety upgrade on a single swing gate. Call (877) 610-2993 for a site look; you’ll get a written number before we touch anything.
My ranch gate on a Benbrook equestrian lot sags at the latch. Do I need a whole new gate?
Usually not. A sag at the latch usually means the hinge post has rolled or the hinge barrels are worn, not that the gate frame itself is ruined. We weld a new hinge sleeve onto the existing pipe, reset the post with a deeper footing, and straighten the frame with heat and patience. Rebuilding a 12-foot ranch gate like that is often $300 to $700 in labor-all in-before you’d think about replacing the gate itself for $2,000 or more. When the pipe is rusted through or the frame has cracked at the welds, we’ll say replace-and we’ll show you exactly why. Call (877) 610-2993 for an honest read on it.
What is the better choice for a long driveway in Benbrook: a swing or slide gate?
For a driveway over about 60 feet with any slope toward the road or toward the lake, a slide gate is almost always the better answer. Swing leaves that long get caught by wind and require bigger posts with more torque load at the hinge. A slide gate on a cantilever track doesn’t fight that battle. Benbrook properties off Winscott and Old Granbury with long rural drives lean slide. For flat, short driveways on standard lots, a swing gate is simpler and cheaper. We’ll tell you which one fits your actual site, not which one pays us more. Call (877) 610-2993 and Hal or his crew will measure it free.
Are solar operators reliable for Benbrook’s iron driveway gates?
Solar operators work in Benbrook, but not with the panels the box stores sell. North Texas heat and the occasional hail storm shorten cheap panel life, and a lead-acid battery in a plastic box won’t survive a Benbrook summer. We fit solar kits sized to the operator draw, with panel mounts that can be tilted and secured, and batteries we know hold up. For a gate that cycles more than six or eight times a day, we typically recommend running power instead. Call (877) 610-2993 and we’ll check your gate’s cycle count and tell you straight if solar will do the job.
Gate Installation work in Benbrook comes down to knowing this specific ground. We do. If you’ve got a gate problem, call (877) 610-2993 now. You’ll get a real person and a straight answer. Free estimates, upfront written pricing, and a 90-Day Done Right Promise on every Benbrook job Hal’s shop touches.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Benbrook since 2001 - we also provide our Gate Access Control in Benbrook.