Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Norman
Gate access control in Norman usually means one of three things: a keypad that stopped accepting codes, a phone entry system that won’t ring through, or a builder-installed opener from the 2000s that’s finally given up after years of Oklahoma wind and red-clay heave. We fix all three, usually same day, and we don’t tell you to replace a gate that just needs the post reset and the board reprogrammed. If your gate won’t respond to the keypad, remote, or phone system, call (877) 610-2993 and talk to a real person who knows Norman gates.
We’ve been at this since 2001. Hal Gatewood’s name is on the shop, his address is published, and the person who answers the phone at 3 a.m. is the same person who will show up at your gate off Tecumseh Road or down in 73026. That matters when you need Gate Repair - Norman because your gate is stuck open and your dog is making a run for it.
Why Gatewood Fence & Gate Is Norman’s Preferred Gate Access Control Company
Homeowners seeking Norman Gate Installation call us because we stock the specific parts their gates actually use. In the 73026 subdivisions off 24th Avenue NW, dozens of neighborhoods share nearly identical builder-installed iron swing gates from the 2000s and 2010s. The hinge hardware, latch styles, and control boards are the same three or four components across entire blocks. We keep those parts on the truck. That means when a Viking keypad dies on a 2009 builder gate in Brookhaven or a DoorKing board loses its programming in Summit Lakes, we don’t waste half your afternoon running to a supply house in Oklahoma City.
We also understand what Norman’s soil does to gates. Cleveland County clay expands when wet and contracts when dry, and after a spring thunderstorm, posts that looked plumb last month are suddenly racked a half inch out. The gate binds, the operator stalls, and you’re stuck. We reset the post, re-plumb the hinge, and then fix the access control problem. Skip the post and you’ll fix the operator twice. That’s not a slogan. That’s the job.
Our Gate Access Control team has been serving Norman long enough to know which neighborhoods heave worst, which builder gates were undersized for Oklahoma wind, and which control boards fail after the third freeze-thaw cycle. You get the benefit of that knowledge on every call, whether you’re off Classen Boulevard near the OU campus or out west past 24th Avenue NW.
Every job carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings us back. No runaround, no “well, that’s a separate issue now.” Hal stands behind the work with his name on the invoice.
Our Gate Access Control Services in Norman
Keypad Entry
A keypad that won’t take codes in Norman is usually one of three things: a board that lost its programming, corroded wire connections from our wet springs, or a keypad that the previous owner’s handyman wired wrong from day one. We replace or reprogram keypads on LiftMaster, Viking, Linear, FAAC, and BFT systems. If your keypad is piggybacked onto an older operator, we’ll tell you honestly whether the keypad is the problem or just the first symptom. A typical keypad replacement or reprogram in Norman runs $150-$325 depending on the brand and whether we’re repairing wiring or starting fresh.
Remote Control
When a remote stops opening the gate from the street, Norman homeowners sometimes assume the remote battery is dead. Half the time the remote is fine and the receiver board in the operator has failed, often because moisture got into the housing during one of our humid summers. We test the remote, the receiver, and the antenna before selling you a part you don’t need. That’s the repair-first approach Hal has run the company on since the beginning. Adding or replacing remotes for a Gate Motor & Opener in Norman typically runs $85-$160 per remote, including programming.
Phone Entry
Phone entry systems let you open the gate from your cell or a landline, and they matter in Norman because so many homes have long driveways or alley-access gates where guests can’t reach a keypad from the driver’s seat. We install and service phone entry on FAAC, BFT, and Linear operators, and we can usually retrofit phone entry onto a 2008-era builder gate without replacing the whole operator. A full phone entry installation in Norman runs $450-$900 depending on whether we’re wiring to an existing opener or starting from scratch.
Card Reader
Card readers show up more on Norman properties with multiple drivers or small businesses operating out of home offices. We install and repair card reader systems on Viking and DoorKing openers, including the older DoorKing units that are everywhere in 1970s-1990s neighborhoods near the OU campus. If your card reader stopped reading, it’s often a wiring fault at the reader head or a failed control board relay, not the cards themselves. Card reader repair in Norman typically runs $200-$450; full installation with reader, cards, and programming runs $600-$1,100.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Norman
We’re certified to service nine major gate brands, and in Norman the ones we see most are Viking, FAAC, BFT, and Linear, plus a healthy share of older DoorKing boards in homes built during the 1980s and 1990s campus boom. We stock replacement boards, keypads, remote receivers, and safety photo-eyes for those brands specifically because we know what Norman gates are made of. When your Viking keypad fails on a Sunday morning, we’re not ordering parts from Dallas and coming back Thursday. We’re fixing it that day.
Common Gate Access Control Problems We See in Norman Homes
- Post heave from expansive clay: Cleveland County’s heavy clay soil expands and contracts with every wet-dry cycle, and by late spring your hinge post has shifted enough that the gate binds against the rack. The operator starts grinding, then stalls. We reset the post to plumb and re-align the rack before we touch the electronics.
- Wind-tripped safety photocells: Norman’s straight-line winds routinely exceed 60 mph during fast-moving thunderstorms, and on lightweight slide gates that flex is enough to trip the safety photo-eye and leave the gate stuck open or closed. We check the alignment and the mounting plane, not just the lens.
- Obsolete control boards losing programming: DoorKing and older Viking boards from 2000s tract construction fail after years of freeze-thaw cycles. The keypad loses its codes, the remote receiver goes dead, or the board stops responding entirely. We stock replacements and can often swap the board same day in Norman.
- Bypassed safety photocells from previous repairs: We find this constantly in Norman. A previous company bypassed the photo-eye to fix a false-obstruction fault, and now the gate closes on anything in its path. That’s a safety hazard and a UL 325 violation. We reinstall compliant photo-eyes on every access control repair we do.
Pricing for Gate Access Control in Norman, OK
Here’s what you’ll actually pay in Norman, based on the jobs we do most often. Keypad replacement or reprogram: $150-$325. Remote replacement and programming: $85-$160 per remote. Phone entry installation: $450-$900. Card reader repair: $200-$450. Safety photocell retrofit: $180-$350 per photo-eye, including the wiring fix that usually caused the bypass. Control board replacement: $300-$650 depending on brand and age.
What moves the price is whether the post is still plumb and whether the existing wiring is salvageable. If the clay has shifted your post, that’s an additional $250-$500 to reset and re-plumb, and we’ll tell you that before we touch anything. The price we quote before the work starts is the price you pay when it’s done. No trip charge inside Cleveland County, $40 off any repair over $200, and a free second opinion on any written estimate from another company. Seniors and veterans get 10% off every job, every time. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Norman
We work throughout Cleveland County and the surrounding area. Our crews serve Gate Access Control in Norman plus the communities of Noble, Moore, Newcastle, and Blanchard. If you’re just south of the river or a few miles east, odds are good we already have a truck nearby. Scheduling is coordinated from our Oklahoma City office, and we run calls in Norman every single day.
Serving Norman, OK - Our Local Coverage Area
We’re based in the Norman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Norman
The most likely cause is that straight-line winds flexed the gate panel enough to trip the safety photocell, or the storm’s rain caused the clay around your hinge post to swell and throw the gate out of alignment. Both are common in Norman after spring storms. The gate’s safety system is doing its job by refusing to close, which doesn’t make it less frustrating when you’re standing in the driveway at 10 p.m. We check the photocell alignment first, then the post, then the operator. Call (877) 610-2993 and we’ll come diagnose it - estimates are free.
In most cases, yes. An operator from 2008, even a builder-installed unit in 73026, usually has an open relay or accessory terminal that accepts a phone entry system. The limiting factor is the control board, not the gate’s age. We’ve added phone entry to 2008-era Viking and BFT operators throughout west Norman without replacing the opener. A retrofit runs $450-$900, and we’ll tell you during the free estimate whether your existing board can handle it or whether you’re better off replacing the board at the same time. Call (877) 610-2993 for an exact quote.
Norman’s winter freeze-thaw cycles cause two problems: moisture gets into control board housings through hairline cracks, and soil movement around posts accelerates, which stresses hinges and racks. The electronics corrode internally, and keypads lose programming when the board’s memory chip fails from repeated expansion and contraction. We see the damage show up in early spring, right when people start using their gates daily again. The fix usually involves a new board and sealing the housing properly this time. A board replacement in Norman runs $300-$650.
The 73026 subdivisions built in the 2000s and 2010s used a lot of Viking and Elite swing-gate operators paired with LiftMaster accessories, and many share nearly identical iron driveway gates. We service all of those brands and stock the era-specific hinge hardware and latch styles those Norman builders used. That means we can fix most 73026 gate access problems without ordering parts. Call (877) 610-2993 and tell us the neighborhood - chances are we already know the gate.
Yes, you should fix it immediately. A bypassed safety photocell means your gate will close on a person, a pet, or a car without stopping, and that’s a UL 325 violation and a serious injury risk. We see this constantly in Norman, usually from a previous company that jumped the photo-eye to stop a false-obstruction fault instead of realigning the sensor. We reinstall a compliant photo-eye, fix the underlying alignment or wiring problem, and test it properly. The retrofit runs $180-$350, and the 90-Day Done Right Promise covers it in writing. Call (877) 610-2993 and we’ll get it done right.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Norman since 2001.