Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Daly City
Gate access control in Daly City usually means one of a few things: a keypad that won’t accept the code, a phone entry system that rings but won’t open, an old operator with a dead control board, or a side gate that’s sagged so far the latch won’t catch. We handle all of it. Most Daly City calls get a same-day or next-day visit, and the price is quoted and agreed before any work starts. If you’re locked out of your own driveway on a foggy Westlake morning, call (877) 610-2993 and a live person answers, day or night.
We work throughout Daly City daily, from the Doelger-built rows of Westlake to the hills above John Daly Boulevard and the flatlands near Junipero Serra. We know these gates because we’ve been repairing them for years. The salt air off the Pacific, the near-daily marine layer, and the uniform 1940s and 1950s housing stock mean Daly City gate jobs follow patterns a generalist gate company won’t recognize.
Why Gatewood Fence & Gate Is Daly City’s Preferred Gate Access Control Company
Hal Gatewood has owned and operated this company since 2001. His name is on the shop and on every invoice, and when you call, a person answers. Not a voicemail tree. Not an answering service in another state. That matters in Daly City, where homeowners have been burned by national outfits that quote one price on the phone and hand over a different invoice at the door.
Our crew knows the Westlake district block by block. We’ve repaired enough Doelger side gates to recognize the original strap-hinge configuration before we even get out of the truck. A sagging gate in the 94015 ZIP often has the exact same failed hinge post as the house three doors down. That local knowledge saves you time and money, because we diagnose faster and we bring the right parts the first trip.
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, Hal comes back and makes it right. No runaround. That promise applies to every keypad retrofit, phone entry install, and operator replacement we do in Daly City.
Our Gate Access Control Services in Daly City
Keypad Entry
A keypad entry system on a Daly City side gate takes a beating from the marine layer. Salt-laden moisture works into the housing, corrodes the contacts, and eventually the code stops registering. We replace dead keypads with sealed units built for coastal exposure, and we mount them where your hand actually reaches, not where a template says to. A typical keypad replacement or new install in Daly City runs $220 to $480, including the keypad and the wiring run. If your existing keypad still works but the operator won’t respond, the problem is usually the control board, not the keypad, and we’ll tell you that before quoting a part you don’t need.
Phone Entry
Phone entry works well in Daly City’s multi-unit buildings along Mission Street and in the duplex-heavy stretches of the 94014 ZIP. The challenge here is age. Many of these systems were installed in the 1990s or early 2000s, and the legacy boards short out from years of damp air. We retrofit existing phone entry panels with modern replacements that still work with the building’s existing wiring, so you don’t have to tear out walls. Phone entry retrofit pricing in Daly City typically runs $450 to $900 depending on the number of entry stations and wiring condition.
Remote Control
Remote control systems are the entry point for most Daly City homeowners with a driveway gate. The remotes themselves rarely fail, it’s the receiver. Salt corrosion on the antenna connection or a failing legacy receiver board means the remote works only when you’re six inches from the gate. We test the range, check the receiver, and replace only what’s dead. A new receiver and two remotes in Daly City usually runs $180 to $350, and we program everything on site before we leave.
Card Reader
Card readers are common at the apartment buildings and condos along Gellert Boulevard and in the newer developments near the 94016 ZIP. We install and service proximity readers, and we repair the wiring runs that get chewed by the damp. A single card reader replacement in Daly City runs $300 to $650, including reader, mounting, and tie-in to the existing operator.
We also handle Gate Access Control work that overlaps with gate repair: video intercoms tied to access systems, smart access retrofits, and full operator replacement when the old motor is past saving. If your gate uses a phone entry panel and you want video too, that’s a common upgrade for Daly City homeowners who can’t see the street from the kitchen.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Daly City
We service and install Linear, Viking, and DoorKing gate access control equipment, along with six other major brands. For Daly City customers, we keep common Linear control boards and Viking entry panels in stock locally, because waiting a week for a part when your gate is stuck open isn’t acceptable. Hal’s crew is certified on every brand we touch, and we have the programming cables and software to set up access codes, phone numbers, and card credentials on site. If your existing system is a Viking and you want to stick with Viking, we’ll do that. If the repair economics say switch to Linear, we’ll show you the numbers and let you decide.
Common Gate Access Control Problems We See in Daly City Homes
- Corroded hinge posts and strap hinges. Daly City’s marine layer puts salt on every piece of ferrous hardware. Untreated side-yard gate hinges in the 94015 and 94014 ZIP codes can fail in five to eight years. The gate sags, the latch misses, and the access control hardware gets blamed when the real problem is the post below it.
- Dead legacy control boards. Pre-2000 operators with original control boards short out from salt-laden dampness. The keypad dies, the phone entry stops ringing, and the remote quits. When a board is dead, we tell you honestly whether it’s worth replacing the board or the whole operator.
- Safety sensor misalignment from shifting posts. Older Doelger-era gate frames in tight 36 to 42 inch openings were not built for modern safety photocell mounts. When the post shifts, the photocell loses its alignment and the gate won’t close. We re-shim, re-anchor, or replace the post, then remount the sensors so they actually line up.
- Keypad housings filled with fog moisture. Keypads installed without proper sealing gaskets trap condensation. Daly City’s fog does the rest. The buttons work intermittently, then stop. We replace with sealed coastal-rated keypads and silicone the mounting screws so the next fog season doesn’t kill it.
Pricing for Gate Access Control in Daly City, CA
Here’s what you can expect to pay in Daly City. A keypad replacement or new install runs $220 to $480. A remote receiver with two remotes runs $180 to $350. A phone entry retrofit for a small building runs $450 to $900. A card reader replacement runs $300 to $650. A full operator replacement with entrapment protection starts around $900 and goes up based on gate size and whether we need new posts.
What changes the price in Daly City specifically is corrosion. If the hinge post is rotted, that’s an additional $150 to $400 depending on how deep the post is set and whether we can use a galvanized anchor. If we have to cut out and replace a section of the gate frame, that adds welding time. You’ll know the full number before we start, and we honor it. No trip charge inside the county, and we offer a free second opinion on any written estimate from another company. Seniors and veterans get 10% off, permanently. Call (877) 610-2993 and we’ll give you a straight number.
We Also Serve Cities Near Daly City
Our Gate Access Control in Daly City team also covers the surrounding neighborhoods and cities. If you’re in Visitacion Valley right over the hill, South San Francisco, Noe Valley, or the Mission District, we can get to you quickly, often the same day. The fog and salt don’t stop at the city line, and neither do we.
Serving Daly City, CA - Our Local Coverage Area
We’re based in the Daly City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Daly City
Westlake sits directly in the Pacific marine layer, meaning near-daily fog and constant salt-laden moisture on every exposed metal surface. Inland Bay Area cities dry out between fog events; Westlake rarely does. Steel hinges and untreated lag bolts that might last fifteen years in Walnut Creek will fail in five to eight years here. That’s why we recommend galvanized or stainless hardware on every Daly City side gate we touch. Call (877) 610-2993 and we’ll assess your hardware before it fails completely.
Yes. The narrow 36 to 42 inch Doelger side-gate openings are tight, but we retrofit them regularly. We weld a galvanized mounting plate for the keypad, run low-voltage wiring through the existing frame, and add UL 325 entrapment protection with photocells mounted on custom brackets. The original gate stays in place. You keep the period look and get a working keypad and a safe operator.
If your operator was installed before 2000, it may not have entrapment protection, which UL 325 has required for automatic gate operators for years. The test is straightforward: if the gate meets resistance while closing, does it reverse before causing injury? Without working photocells or a reversing edge, it won’t. We inspect the operator, the sensors, and the wiring, and we tell you plainly if it meets current safety requirements or needs a retrofit. This is a serious safety matter, and a trained professional should do the inspection. Call (877) 610-2993 to schedule one.
Because the hinge post itself is moving, not the hinge bolts. In Westlake, the original 1950s posts are often set in concrete that has cracked, or the post base is rusted through below ground level. Tightening the bolts just pulls a rotting post further out of alignment. We reset the post in a galvanized anchor or replace it entirely, then re-hang the gate. Fix the post and the sag goes away. Fix the panel without the post and you’ll fix it twice.
Yes, and we do it often. The Doelger-built homes in Westlake have nearly identical side-yard gate configurations. When we finish one job on a block off Southgate Avenue, we’ve diagnosed the template for the whole street. On a fog-heavy afternoon last year, our tech replaced a corroded control board and a rotted hinge post on one Southgate house, then knocked on three neighboring doors with the same gate style and booked two more keypad retrofits before leaving the block. If you have neighbors with the same issue, tell us when you call. We’ll handle them all in one trip.
If you’re dealing with a dead keypad, a phone entry system that won’t ring, or a gate that sags against a rusted post in Daly City, call (877) 610-2993 today. Hal or one of his crew will answer, talk you through what’s happening, and give you a straight price before anyone shows up. Free estimates, no trip charge inside the county, and the 90-Day Done Right Promise on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Daly City and the surrounding Bay Area since 2001.