Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Florence-Graham, CA
A gate that drags on the concrete, won’t latch, or starts swinging on its own isn’t something you put off in Florence-Graham. This is one of the densest unincorporated communities in California, and a gate left half-open on a 30-foot lot puts everything you own in view of the sidewalk. We answer the phone around the clock at (877) 610-2993, and most repair calls in the 90001 ZIP get same-day or next-morning service. The gates here are different from what you’d find in a tract-home suburb, and we treat them that way.
Why Florence-Graham Homes Are Different
Florence-Graham sits far enough inland that it misses the heavy marine layer which keeps coastal neighborhoods damp and, oddly, slows rust down. The air here is dry, but the sun is relentless. Ornamental iron that lost its paint years ago oxidizes in a flaky, scaly way that works into hinge barrels and post sockets until the only option is cutting old bolts off with a torch. Then the Santa Ana winds barrel through the flat basin and rack lighter gate frames right off their hinges, pulling posts half an inch out of concrete footings that were undersized to begin with. The homes themselves, most built in the 1940s and 1950s on 25 to 40-foot lots and many since converted to multi-family use, were never designed for automatic operators. That means the driveway gate is almost always custom-fitted, and decades of piecemeal welded repairs have left layers of mismatched steel and heavy paint on the original iron. Add in the fact that Florence-Graham is unincorporated, so LA County Department of Regional Planning holds permitting authority, and you get a community where a striking number of gates were installed informally without permits. That reality shapes every repair call we take here.
Gate Repair in Florence-Graham
Most gate repairs in Florence-Graham run from $120 to $380 depending on what’s actually failed. We quote the exact price in writing before any work starts, and that number doesn’t change unless you add scope and approve it first. When we pull up to a house off Florence Avenue or Firestone Boulevard, we’re usually looking at a gate that was welded to fit a narrow driveway in the 1960s, repaired in pieces over decades, and now sagging because the hinge post has moved. Our first priority is getting the gate secure again, then making the fix that lasts. For the full scope of what we handle, see our Gate Repair page.
Hinge and Post Repair
Most of the original ornamental iron gates in Florence-Graham went in during the 1940s through the 1960s, and the posts were set in shallow concrete. Decades of wind loading and soil movement leave posts leaning and hinges pulling until the gate drags on the concrete. Hinge replacement and post repair typically runs $180 to $380, depending on whether we need to reset the post in new concrete.
Electric Gate Repair
Electric gates in the 90001 ZIP are usually retrofits on older homes, wired straight off the main panel and often without a dedicated circuit or a UL-listed disconnect. When a gate stops holding a charge or opens halfway, we start with a compliance check before touching a wire. Most electric gate repairs run $140 to $320, with the exact figure quoted before any work begins.
Gate Realignment
A gate that scrapes the driveway or won’t latch is often still structurally sound. The pivot hinges wear, the post shifts half an inch, and now the latch misses the strike. Realignment in Florence-Graham typically runs $90 to $180, and it’s a same-visit fix. Fix the panel without the post and you’ll fix it twice, so we start with the post.
Why does my gate keep sagging after I fix the panel?
The panel usually isn’t the problem. A gate sags in the hinge post, not in the middle, and on Florence-Graham’s older homes the post is almost always what’s failed at the footing. Reset or replace the post and rehang the existing gate. If the panel is racked from years of sagging, then replacement makes sense. Call (877) 610-2993 and we’ll tell you which one you’re looking at.
Can you come today for a gate repair in Florence-Graham?
In almost every case, yes. We run routes through the 90001 ZIP every weekday, and a gate stuck open or a car blocked in counts as an emergency. Call (877) 610-2993 and a live person tells you exactly when someone will arrive. No voicemail, no call center, no queue.
Gate Installation in Florence-Graham
A new gate installation in Florence-Graham typically runs $2,800 to $7,500 for a driveway gate, $900 to $2,200 for a pedestrian gate, and $3,500 and up for a sliding gate. Narrow lots, unincorporated county rules, and custom-fitted openings mean almost nothing here is off-the-shelf. We measure on site, build to the actual opening, and quote the total in writing before any work starts. For details on materials and options, see Gate Installation.
Driveway Gate
Most Florence-Graham driveways sit on 25 to 40-foot lots, so a standard warehouse gate won’t fit. We custom-fit every driveway gate to the opening we measure ourselves. On the east side of Alameda Street and the blocks around Graham Avenue, we regularly build gates that work with the long narrow driveways of converted multi-family homes. A typical driveway gate installation runs $2,800 to $7,500.
Swing Gate
Swing gates are the most common style in Florence-Graham’s post-WWII housing stock, and the most common failure is the post pulling from an aging concrete footing. We don’t just rehang the panel; we set new post footings so the gate doesn’t sag again in two years. Swing gate work with new footings typically runs $2,200 to $5,800.
Sliding Gate
The flat basin terrain means Florence-Graham has plenty of slide gates, but many were installed on light-duty tracks that have been patched and re-welded for decades. We see rack and pinion gates binding or jumping track, especially after Santa Ana winds push dust and debris into the rollers. Sliding gate installations start around $3,500 and go up with track length and motor needs.
Do I need an LA County permit to replace my gate in Florence-Graham?
In most cases, yes. Florence-Graham is unincorporated, so LA County Department of Regional Planning holds authority over gate permits and inspections. A like-for-like panel swap may not trigger a permit, but new post footings, automatic openers, or electrical work usually do. We handle the paperwork and can walk you through retroactive permitting for gates installed without county approval. Call (877) 610-2993.
Should I replace the panel or the hinge post on my 1960s gate?
Start with the hinge post. On a Florence-Graham home from the 1960s, the post is usually what’s failed at the footing. If the panel is still square and the welds are solid, we reset or replace the post and rehang the existing gate. If the panel is racked from years of sagging, then replacement is the honest call. We’ll tell you straight.
Gate Motor & Opener in Florence-Graham
A gate motor repair in Florence-Graham typically runs $225 to $475, and most opener jobs wrap up in a single visit. That matters when your driveway gate is the only thing between the street and your front door. Because so many automatic operators in the 90001 ZIP were wired directly into panels without county permits, we check the electrical side before we diagnose the motor. For full details on what we service, see Gate Motor & Opener.
Motor Repair
Repair is more common than replacement here, and that’s how we prefer it. A blown capacitor, a failed limit switch, or a worn gear gets fixed on its own, not swapped out as part of a unit you didn’t need. Given how many Florence-Graham openers were installed informally, repair is often the smarter and safer path. Most motor repairs land between $225 and $475.
Slide Motor
Slide motors make sense when a swing gate would arc into a car or a wall, which describes a lot of these tighter lots. We install and repair slide operators from Viking, FAAC, and Ghost Controls, and we always inspect the track and roller condition at the same time. Slide motor repair typically runs $250 to $520 in the 90001 ZIP.
Motor Installation
Installing a motor on a custom-fitted gate is rarely a bolt-on job. We measure the gate’s weight and cycle count, recommend the right operator, and handle the power run so it meets LA County electrical requirements. A typical Florence-Graham motor installation runs $850 to $1,650 including labor and hardware.
Why does my gate opener strain during Santa Ana winds?
Wind pushes your gate hard enough to flex the frame, which changes the track geometry and forces the motor to work against a gate it wasn’t designed to move. Worn hinge posts and rollers make it worse. We check the mechanical side first, because no motor survives long against a gate that fights the wind. Call (877) 610-2993 for a diagnosis.
Do I need a permit to repair my gate motor in Florence-Graham?
A like-for-like component swap usually doesn’t require a new permit, but a new electrical run, a new operator installation, or a gate that was never permitted does. Florence-Graham has no city building department, so LA County rules apply directly. We’ll tell you what your gate needs before we touch anything.
Gate Access Control in Florence-Graham
Gate access control in Florence-Graham typically runs $450 to $2,800 depending on whether you’re adding a keypad to an existing opener or pulling permits for a full video intercom on a custom iron gate. Most access control repairs in the 90001 ZIP get done in one visit because we keep common boards, keypads, and photocells stocked. The full range of what we install and service is on our Gate Access Control page.
Keypad Entry
A keypad is the most common access control upgrade in Florence-Graham because it works for dense households with multiple drivers, visiting family, and delivery access. We mount weather-sealed keypads rated for direct sun, program unique codes, and tie the keypad into your existing FAAC, BFT, Linear, or Viking operator. A basic keypad installation runs $450 to $800.
Phone Entry
Phone entry lets a visitor at the gate call a number you control, and you open the gate from anywhere. That’s the practical answer for Florence-Graham properties converted from single-family to multi-family use, since it eliminates sharing gate codes between units. A phone entry system with cellular bridge runs $900 to $1,800 installed.
Smart Access
Smart access means opening your gate from your phone, with visitor logs and scheduled access windows. In Florence-Graham’s unincorporated permit landscape, we often combine a smart upgrade with the required electrical compliance correction, since many existing operators were wired without a UL-listed disconnect. A smart access retrofit with compliance correction typically lands $1,200 to $2,400.
My gate keypad stopped working after a wind event. What should I check?
Check whether the gate post is still plumb. Santa Ana wind loading racks lighter swing gates off their hinge posts and breaks the wire run to frame-mounted keypads. If the keypad lights up but the gate doesn’t move, the photocell is likely out of alignment from the same wind. Call us for a same-visit diagnosis.
Can you install a video intercom on a custom-welded gate?
Yes, and we do it regularly in Florence-Graham because most driveway gates here are custom-fitted to narrow openings. We mount the intercom station on a solid post or reinforced frame section, run wiring in weather-sealed conduit, and tie the video feed to a monitor or your phone. A full video intercom with gate release runs $1,800 to $2,800.
Gate Parts & Welding in Florence-Graham
Most gate failures in Florence-Graham aren’t fixed by bolting on a part from a big-box store. They’re welded seams that gave out after thirty years, hinge posts rusted through at the base, and rails cracked by decades of wind loading. We weld on site, in your driveway, so the gate never leaves your property. For the full scope of what we fabricate and replace, see Gate Parts & Welding.
Hinge Replacement
On Florence-Graham’s narrow lots, driveway gates rarely have standard swing clearance. A hinge that fails usually means the post has started to lean, because the hinge was carrying more weight than it was ever meant to. We replace the hinge, but first we check the post and frame alignment. A hinge replacement typically runs $140 to $320.
Post Replacement
Santa Ana winds push hard through the flat South LA basin. When a post pulls out of aging concrete or rusts through at ground level, the entire gate loses its reference point. Post replacement runs $380 to $850, including removing the old footing when needed. Skip the post and patch the damage, and you’ll be calling someone again before the next wind season.
Rail Repair
Decades of welded repairs and paint layers hide rail failures until they snap. On Florence-Graham’s older ornamental iron, the top and bottom rails take the brunt of gravity and wind every single day. Hal cuts out the bad section, welds in matching steel, and grinds it clean. Rail repair runs $180 to $430 per rail section.
Custom Welding
Some jobs don’t have a part number. A gate custom-fitted to a 1960s driveway opening isn’t going to match anything off a shelf. On-site welding fixes the panel, reinforces the frame corner, or fabricates a bracket that never existed in the first place. Custom welding starts at $75 per hour plus materials, and most repair welds finish in one to three hours.
How much does welding a broken gate cost in Florence-Graham?
Expect $75 per hour for welding labor plus materials, with most repair welds finishing in one to three hours. The total for a snapped rail or cracked frame corner typically stays between $200 and $500. The exact number is quoted and agreed before work starts. Call (877) 610-2993 for a free estimate.
Is welding done on site, or do you haul the gate away?
On site, in your driveway. No disassembly, no flatbed, no waiting days for your gate to come back from a shop. Repairing in place is faster, usually cheaper, and doesn’t risk damaging a gate that was custom-fitted to a non-standard opening in the first place.
Brands We Service in Florence-Graham
We service and repair FAAC, BFT, Linear, and Viking operators, along with several other major brands. We keep common boards and sensors stocked on the truck, so most repairs don’t wait on parts. See our brands for the full list of what we work on.
Pricing for Gate Repair in Florence-Graham, CA
| Service | Typical range in Florence-Graham |
|---|---|
| Gate realignment | $90 - $180 |
| Hinge replacement and post repair | $180 - $380 |
| Basic hinge or latch repair | $120 - $220 |
| On-site weld repair | $180 - $350 |
| Electric gate repair | $140 - $320 |
| Motor repair | $225 - $475 |
| Slide motor repair | $250 - $520 |
| Custom welding (per hour) | $75 + materials |
| Post replacement | $380 - $850 |
| Keypad installation | $450 - $800 |
What pushes the price up in Florence-Graham is the physical condition of the gate when we arrive: rusted posts, unpermitted wiring, and frames racked by years of wind loading all add labor. Every price is quoted and agreed in writing before any work starts, and that number does not change unless you add scope and approve the additional amount first.
Neighborhoods We Serve in Florence-Graham
We cover the entire 90001 ZIP, from the Florence Avenue corridor south to the 105 boundary and from Alameda Street east to Central Avenue.
- Florence Avenue corridor
- Firestone Boulevard blocks
- Alameda Street residential side streets
- Graham Avenue neighborhoods
Most Florence-Graham calls get same-day or next-morning service, and a live person answers 24 hours a day.
Service Area - Cities Near Florence-Graham
Our crews serve Florence-Graham, CA and the surrounding communities across the South LA basin. We regularly work in Huntington Park, CA, Walnut Park, CA, Willowbrook, CA, South Gate, CA, and Cudahy, CA. Dispatch is coordinated from our Los Angeles office, and crews serve Florence-Graham locally.
Serving Florence-Graham, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Florence-Graham and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Florence-Graham coverage area; if your address is on it, we can help.
Also serving nearby: Florence-Graham, CA, Huntington Park, CA, Walnut Park, CA, Willowbrook, CA, South Gate, CA, Cudahy, CA.
FAQs About Gate Repair in Florence-Graham
Most repair calls in the 90001 ZIP get same-day or next-morning service. We run routes through Florence-Graham every weekday, and a gate stuck open or a car blocked in is treated as a priority. Call (877) 610-2993 and a live person tells you exactly when someone will arrive.
Often yes. Florence-Graham is unincorporated, so LA County Department of Regional Planning holds permit and inspection authority. New post footings, automatic openers, and electrical work usually require county approval, and retroactive permits for informally installed gates are common. We handle the paperwork and tell you what’s needed before any work begins.
Yes. From Florence Avenue south to the 105 boundary and from Alameda Street east to Central Avenue, every address in Florence-Graham is inside our service area. There’s no trip charge inside the county, and the 90-Day Done Right Promise applies to every repair we make. Call (877) 610-2993.
If your gate is sagging, stuck, or refusing to close, call (877) 610-2993 for a free estimate. Hal Gatewood will look at it himself, tell you what it costs, and you agree before any work starts. The name is on the shop, and the shop is down the road.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Florence-Graham Customers Say
"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu