Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Concord, CA
Gate repair in Concord typically costs between $150 and $450 for most hinge, latch, and realignment work, and we can usually have someone at your gate within 24 hours. Concord’s particular mix of 1960s ranch housing, expansive clay soil, and triple-digit summer heat creates gate failures we see block after block. Call (877) 610-2993 and you’ll get a live person who can tell you straight what the fix will take.
Why Concord Homes Are Different
Concord exploded from roughly 6,000 residents in 1950 to nearly 100,000 by 1980, and the city built out in vast tracts of ranch-style homes whose original gate systems are now hitting the 50 to 60 year mark all at once. The 4×4 posts holding many of those gates were set directly in Concord’s expansive clay soil, which heaves through wet winters and shrinks in the dry summer cycle. Posts lean, latches stop lining up, and gates start dragging or won’t close at all.
The heat makes it worse. Concord sits in the inland Diablo Valley, not the fog belt, and summer highs regularly run 98 to 105°F with very low humidity. Wood that survives in Oakland or Walnut Creek splits and checks here. Add the seasonal Diablo winds that funnel through the Carquinez corridor in late summer and fall, and you get repeated lateral stress on gate frames, loosening hinge screws and racking gates off-square. We see the same pattern across central and west Concord, from the 94519 and 94520 tracts up through 94518 and 94529.
Gate Repair in Concord
Most gate repairs in Concord land between $150 and $450, and the work usually wraps up the same day. The most common call we get from the ranch tracts off Cowell Road and the neighborhoods near Monument Boulevard is a gate that won’t latch or won’t close at all, because the post has moved and the hinges are pulling out of dried-out wood. Hal or one of his crew will diagnose it on site, quote the number before any work starts, and fix what actually failed. We weld in the driveway, not in a shop. For the full scope of Gate Repair work we handle, see the hub page.
Hinge & Post Repair
Concord sits on expansive clay in the Diablo Valley, the same clay that shifts foundations here also heaves gate posts out of plumb every wet-dry cycle. A 4×4 post set in 1968 has been through about 57 years of that movement, and now it leans, the latch binds, and the hinges are pulling screws out of desiccated wood. Post reset and concrete work runs $220 to $480 depending on footing depth and gate weight, and hinge and latch fixes run $150 to $325.
Electric Gate Repair
Electric gate systems in Concord fail in patterns we can nearly predict: capacitor death after a few summers of 100°F afternoons, limit switches knocked out of adjustment, and photo-eye sensors that go sun-blind in the late-afternoon glare. We repair the control board, the safety edges, the receiver, and the wiring, whatever actually failed, rather than swapping the whole operator. Electric opener board, sensor, and arm repairs run $190 to $450 depending on parts.
Gate Realignment
When a double-drive gate’s leaves no longer meet in the middle, or a single gate scrapes the concrete apron every time you swing it, the frame has racked. In Concord, the Diablo winds do a lot of this. Hot, dry gusts funnel through the Carquinez corridor push on wide gate panels, loosening hardware and pulling the frame off-square. We re-square the gate, replace stretched or sheared bolts, and re-hang the hinges so it closes with a click. Realignment work runs $150 to $325.
How fast can you get to a gate repair in Concord?
We generally reach most Concord addresses, including the 94519 and 94520 ranch tracts and the 94527 and 94529 hill neighborhoods, within 24 hours for non-emergency repairs. Urgent gate failures, a gate stuck open, a dropped slide gate, an opener that won’t close, get same-day treatment in most cases. Call (877) 610-2993 and tell us what’s happening.
Can you weld a gate repair on site in Concord?
Yes. We weld on site in your driveway across Concord: broken hinge brackets, snapped weld seams on steel gates, cracked frame corners. Hal brings the welding rig on the truck, so your gate stays put and the repair happens where the gate hangs. We don’t haul your gate off to a shop, and we don’t sell you a new panel when a weld restores the old one.
Gate Installation in Concord
Most gate installations in Concord run between $1,400 and $6,800 depending on the gate type, width, material, and whether automation is part of the job. For a standard single driveway gate on a Concord ranch home, you’re typically looking at $1,800 to $3,200 installed. The full written price comes before any work starts, so the number we quote in your driveway is the number on the invoice. Learn more about our Gate Installation process on the hub page.
Driveway Gate Installation
Driveway gates are the biggest investment, and in Concord they’re usually going on ranch homes with wide frontages. A single gate across a 10 or 12 foot opening is the most common. A standard single swing gate runs $1,700 to $3,000 installed, and a double gate runs $3,500 to $6,500. Steel gates cost more than wood, but they also don’t split in Concord’s summer heat the way a fir board will.
Pedestrian Gate Installation
These are the gates you use every day, walking out to get the mail or letting the dog into the side yard. Most Concord ranch homes have one or two of these, and they take the most abuse. Original wood posts set straight into Concord’s expansive clay are the weak point. We replace the post and set a new one in concrete below the moisture line. A pedestrian gate runs $650 to $1,400.
Sliding Gate Installation
Sliding gates are the right call for driveways with limited swing clearance, or where you need a gate that opens against a slope. In Concord, we see a lot of sliding gates on properties where the driveway butts right up against the neighbor’s fence line, and on steeper lots up toward the 94529 side. Expect $2,800 to $5,500 for a typical Concord sliding gate install, before any automation.
How fast can you get to Concord for a gate installation?
For most installs, we schedule within a few days of your call, not weeks out. We’re in Concord multiple times a week already, from Clayton Road to Willow Pass Road. If you need a gate measured and quoted, call (877) 610-2993 and we’ll come out and give you a written number the same day.
Do you install gates with motors and access control in Concord?
Yes. We install the gate and handle the automation too, including motors from Viking, DoorKing, and Ghost Controls. If you want a keypad, an intercom, or a system tied into your phone, that’s part of the job. We wire it and set it up before we leave. Call (877) 610-2993 for a free estimate.
Gate Motor & Opener in Concord
A gate motor in Concord has to fight two things the rest of the Bay Area barely notices: triple-digit Diablo Valley summers and clay soil that swells and shrinks under your posts all year. That combination is why openers here burn out, bind up, and strip gears faster than in Oakland or Walnut Creek. We fix and install gate motors across 94518, 94519, 94520, and 94529, and we know what fails on a 1968 ranch off Clayton Road. Details on the full Gate Motor & Opener service are on the hub page.
Motor Repair
We repair what other companies want to replace. If your LiftMaster or DoorKing opener has a bad capacitor, a stripped gear, or a fried control board, we diagnose it on site and fix the actual problem. Most straightforward motor repairs on Concord’s ranch gates land between $225 and $600, and they take one visit. We weld on site too, so if the motor bracket ripped off a rusted gate frame, we repair the frame in your driveway rather than hauling the gate away.
Motor Installation
Most motor installations in Concord happen on gates that were never automated in the first place. A homeowner gets tired of getting out of the car in the rain, or they want the convenience and security of an opener. The problem we run into over and over across 94518 and 94520 is that power was never run to the gate when the subdivision was built. A full new installation with proper conduit and a dedicated circuit starts around $1,400 and goes up from there based on trenching distance.
Slide Motor
Slide gates show up on wider driveways in the 94529 zip and on light commercial properties. The failure mode we see most is the same one that plagues swing openers: heat plus age plus undersized motors. A slide gate that drags because the track has shifted a half inch will cook a motor in one Concord summer. Slide motor replacements generally run $1,100 to $2,200 given the additional track and rack hardware.
What does a gate motor replacement cost in Concord?
A typical gate motor replacement in Concord runs $850 to $1,700 depending on the operator’s size and whether we’re reusing the existing mount. Adding a battery backup is usually $350 to $750. Every quote is written and agreed before any work starts. Call (877) 610-2993 for an exact number on your gate.
Do you service Viking and DoorKing motors in Concord?
Yes. We service Viking, DoorKing, Ghost Controls, Elite, LiftMaster, FAAC, BFT, Linear, and Mighty Mule. We stock common boards, gears, and capacitors for these brands, which is why most Concord motor repairs wrap up in one visit rather than two.
Gate Access Control in Concord
Gate access control in Concord usually comes down to one question: will the keypad, card reader, or remote actually release the gate when you pull up? In most 1960s ranch tracts across 94518, 94519, and 94520, the answer is often no, because the post holding the reader has shifted half an inch out of square and the latch no longer lines up. We fix the post, then fix the access system. See the full Gate Access Control service description on the hub page.
Keypad Entry
Keypads are the most common access system on Concord ranch homes. The problem we see all over 94518 and 94519 is a keypad mounted on a gate post that has rotated with the expansive clay soil, so the deadbolt or latch no longer seats when the code is entered. In Concord, a new keypad install typically runs $350 to $650, including the keypad, wiring or wireless transmitter, and a gooseneck stand if the post is too far out of plumb to use.
Phone Entry
Phone entry systems let a visitor call a number from the gate keypad and have you buzz them in from your cell phone. These are popular on Concord properties with long driveways where you don’t want to walk down to the gate. A phone entry system in Concord typically runs $700 to $1,400 installed, depending on whether it uses a landline, cellular, or internet connection. Cellular is the most reliable here because it doesn’t depend on a home phone line running to the gate post.
Remote Control
Remote control systems use a transmitter in the car and a receiver wired into the gate operator. For a standard single-family gate in Concord, a remote control add-on or replacement runs $250 to $500 per operator. On older LiftMaster or Viking operators, we sometimes replace just the receiver board rather than the whole unit, which saves hundreds. If your remote works in the morning but not in the afternoon heat, the receiver board is usually the culprit.
Why does my Concord keypad work all winter but fail every summer?
Concord’s expansive clay soil swells with winter rain and shrinks in summer heat. The post holding your keypad moves with that cycle. In winter the post sits close to its original position and the latch lines up. In summer the post rotates out of square as the clay dries, so the signal triggers the lock but the bolt no longer seats. Call (877) 610-2993 and we’ll fix the post first.
Does Concord allow solar-powered gate openers?
Yes. Concord permits solar-powered gate operators, and they’re common on longer driveways where running conduit for AC power is impractical. The key in Concord’s heat is sizing the panel and battery correctly. A 100°F summer day bakes dust onto panels, so we angle them for self-cleaning and size the battery for three to five days of cloudy or dusty conditions.
Gate Parts & Welding in Concord
When a gate post rots out or a hinge rips loose in Concord, the fix usually means welding, not shopping for a whole new gate. Most of the original gates across Concord’s 94518, 94519, and 94520 ranch tracts were built with the house, which makes them 50 to 60 years old now. Replacing a hinge you can weld for $140 to $280 is just burning money. We repair first. The full Gate Parts & Welding hub has more detail.
Hinge Replacement
A Concord gate that drags on the latch side almost always has a hinge problem first. The original steel hinges on those 1960s gates pull loose from the wood as it dries and checks, then the gate weight bends the remaining screws and twists the hinge leaf. We cut off the old hinge, weld in a heavier plate if needed, and refasten with structural screws that actually bite into sound wood or a fresh steel post. Hinge replacement runs $140 to $280 per hinge.
Post Replacement
Concord’s clay soil is the quiet killer of gate posts. Summers bake the ground dry and the clay shrinks; winters load it with moisture and it swells. A 4×4 set in that soil fifty years ago is now leaning, cracked at the base, or both. We pull the old post, set a new one in concrete with gravel drainage to slow the seasonal heave, and weld or lag the gate hardware back square. Post replacement in Concord runs $380 to $750 per post, depending on depth, access, and concrete demolition.
Custom Welding
Sometimes the part you need doesn’t exist anymore. The gate manufacturer is gone, the hinge pattern is from 1972, or you want a gate latch that actually matches your 1960s mid-century ranch aesthetic. Hal welds custom brackets, gate stops, latch plates, and steel frames on site. Custom welding starts at about $90 for a small bracket and runs up from there depending on the fabrication.
Can you weld a gate post back together instead of replacing it?
Steel posts can often be welded and reinforced in place. Wood posts that have rotted at the base or split through can’t be reliably welded, and the honest answer is that they need to come out and be replaced. Hal will always repair what can genuinely be repaired, and he won’t pretend a cracked post is fixable just to save a few dollars now.
Does the 90-Day Done Right Promise apply in Concord?
Yes, in writing, on every single job in Concord. If the weld fails, the hinge loosens, or the post shifts within 90 days, one call brings Hal back, no runaround. It’s not pro-rated, and it’s not “up to 90 days.” It’s 90 days, and the paper says so. Call (877) 610-2993 for a straight answer and a straight price.
Brands We Service in Concord
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common boards, gears, capacitors, and receiver parts for Viking, DoorKing, and Ghost Controls right on the truck, which keeps most Concord repairs to a single visit. See our brands for the full list.
Pricing for Gate Repair in Concord, CA
| Service | Typical range in Concord |
|---|---|
| Hinge, latch, or realignment repair | $150 - $325 |
| Post reset and concrete work | $220 - $480 |
| Electric opener board, sensor, or arm repair | $190 - $450 |
| Pedestrian gate installation | $650 - $1,400 |
| Single driveway swing gate installation | $1,700 - $3,000 |
| Double swing gate installation | $3,500 - $6,500 |
| Sliding gate installation | $2,800 - $5,500 |
| Gate motor replacement | $850 - $1,700 |
| Keypad entry system | $350 - $650 |
| Custom welding (small bracket) | $90 and up |
What pushes a Concord job toward the upper end is usually the post. Expansive clay has moved it, concrete demolition is involved, or the gate weight demands a heavier footing. Whatever the number, it’s written and agreed before any work starts, and that’s the number on the invoice.
Neighborhoods We Serve in Concord
We work the whole city, from the ranch tracts where the houses are identical block after block to the hill neighborhoods where the driveways get steeper and the gates get wider. Typical response time for the area is same day for most repair calls, and our no-trip-charge-inside-the-county standing offer keeps the math simple.
- Central Concord (94519, 94520)
- West Concord and the Monument Boulevard corridor (94518, 94520)
- North Concord near the Naval Weapons Station (94520, 94529)
- Lime Ridge and the areas east of the mall (94518, 94521)
Service Area - Cities Near Concord
We serve Concord and the surrounding communities across central Contra Costa County. If you’re in Concord, CA, we’re in your neighborhood regularly. We also work in Pleasant Hill, CA, Contra Costa Centre, CA, Waldon, CA, Walnut Creek, CA, and Pittsburg, CA. The same pricing, the same 90-Day Done Right Promise, and the same live person on the phone.
Serving Concord, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Concord and the communities around it; dispatch is coordinated from our San Francisco Bay Area office. The map shows the Concord coverage area; if your address is on it, we can help.
Also serving nearby: Concord, CA, Pleasant Hill, CA, Contra Costa Centre, CA, Waldon, CA, Walnut Creek, CA, Pittsburg, CA.
FAQs About Gate Repair in Concord
We generally reach most Concord addresses within 24 hours for non-emergency repairs, and urgent gate failures get same-day treatment in most cases. If the gate is guarding a pool or a child’s play yard, tell us when you call and we’ll treat it as a priority. Call (877) 610-2993 and describe what the gate is doing.
Yes. We cover all of Concord including 94527, 94529, 94518, and 94519, from Babel Avenue to the far edge of Willow Pass Road. We’re in these neighborhoods year-round, not passing through on a county-wide route. The same crew that fixes a gate off Cowell Road this week will be back on Landana Drive next week.
Most gate repairs in Concord don’t require a permit. New installations, particularly automated gates with electrical work, sometimes do. We’ll tell you honestly on the first call whether your job needs a permit, and we handle the paperwork when it does. The written quote includes any permit fees, so there’s no surprise at the end.
Call (877) 610-2993 for a free estimate on any gate repair, installation, motor, or access control job in Concord. A live person answers, and Hal or one of his crew will be at your gate with a written price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Concord Customers Say
"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath