Gate Repair in Aloha - Same-Day Repair, Priced Before We Start

Gate Repair in Aloha, OR

Most gate repairs in Aloha come down to three things: the clay moving the post, the damp rotting the rail, or the opener giving up after one too many wet winters. We typically finish common hinge, latch, and realignment jobs for $180-$340, and we can usually be at your door the same day you call. If your swing gate is dragging across the driveway off 185th or the automatic opener near Farmington Road quit listening to the remote, call (877) 610-2993 and you’ll get a live person, not a voicemail tree.

Call (877) 610-2993

Why Aloha Homes Are Different

Aloha isn’t a city. It’s an unincorporated Washington County community, which means gate and fence permits fall under Washington County Land Use and Development Code, not a Beaverton or Hillsboro ordinance. That catches people off guard. Homeowners assume they’re under Beaverton’s rules, then find out structural work has to go through the county permit office in Hillsboro. It can delay a repair when a retaining-wall-adjacent gate is involved, and we’re glad to walk you through exactly what your project needs before you file anything.

The bigger story is the soil. Aloha built out fast from the 1970s through the 1990s, and the dominant housing stock is single-story and split-level ranch homes with standard 6-foot dog-ear cedar fences and swing gates. Many of those original gates are now 25 to 45 years old. The Portland metro’s 37 to 40 inches of annual rain saturates that expansive clay, and posts set without proper gravel drainage heave and lean over successive wet seasons. A gate sags in the hinge post, not in the middle, and that is where we start.

Gate Repair in Aloha

Gate repair in Aloha usually costs between $180 and $340 for a hinge, post, or realignment fix, and most jobs are finished the same morning we show up. If your swing gate drags across the driveway on 185th or the automatic opener off Farmington Road quit listening to the remote, we can likely have it moving again before dinner. We know Aloha’s gates, we know why they fail, and we fix them at the source rather than swapping parts that don’t need swapping.

Electric Gate Repair

Most electric gates in Aloha are swing gates on ranch-style homes built between the late 1970s and the 1990s. The two failures we see most are burned capacitors on the opener control board and limit switches that have drifted after years of damp winters. We diagnose the actual cause, replace only what failed, and test the full cycle a dozen times before we leave. Opener board replacements land between $250 and $450 depending on brand. If a motor is beyond saving and you need a new one, we’ll talk you through what a replacement honestly costs before any work starts.

Hinge and Post Repair

This is where Aloha’s clay soil does its damage. Gate posts set without adequate gravel drainage heave and lean over successive wet seasons, and on a 30-year-old gate, the post base is often rotted below grade where you cannot see it. We dig, confirm what’s actually there, and either reset the post with proper drainage or install a new pressure-treated post. A post reset with proper drainage runs closer to $300 to $600 depending on depth, concrete, and whether the old post needs a new sonotube. Fix the panel without the post and you’ll fix it twice.

Gate Realignment

Realignment is often the difference between a gate you can open with one hand and a gate that fights you every morning. In Aloha, where the ground moves under every fence line, a gate that closed cleanly in August may drag by February. We square the frame, adjust the hinges, and shim or cut the drop rod so the gate latches without lifting. Full gate realignment is typically $150 to $300. It is not glamorous work, but it is the work that makes a gate feel new again for a couple hundred bucks instead of a couple thousand. For more on how we approach repairs, see our Gate Repair page.

How fast can you get to my gate in Aloha?

For most hinge, realignment, and opener failures, we can be at your Aloha home the same day you call. Emergency calls where a gate is stuck open or a vehicle can’t get out are prioritized. Call (877) 610-2993 and we’ll give you a straight answer about when we’ll get there.

Why does my Aloha gate sag every year even after I tighten the hinges?

Because the post is moving in the clay. Tightening hinges on a post that’s heaving out of plumb doesn’t fix anything. The soil in the Tualatin Valley expands when it’s wet and shrinks when it’s dry, and over a few seasons that cycle slowly pushes shallow posts out of line. The real fix is resetting the post deeper with proper gravel drainage, then rehanging the gate. We see this constantly in Aloha.

Gate Installation in Aloha

Gate installation in Aloha typically runs $1,400-$4,800 for a standard driveway swing gate and $2,800-$7,500 for a sliding gate, depending on size, material, and whether we’re automating it. Most Aloha homeowners get a written quote within 48 hours of our free on-site measure, and we schedule installation at a pace that works for your driveway, not ours. If you’re tired of a sagging 40-year-old gate held together by hope and a bungee cord, we measure to the inch and set posts below the frost line with proper gravel drainage.

Driveway Gates

Most Aloha driveways are wide enough for two cars side by side, which means a double swing gate or a single sliding gate. We measure to the inch, set posts below the frost line with proper gravel drainage, and hang the gate so it clears the ground through a full wet season. The clay soils here swell by the inch every winter, and a post set shallow will lean before spring. We don’t set posts shallow. A single swing driveway gate runs $1,400-$3,200 installed, while a double driveway gate is generally $2,600-$4,800.

Pedestrian Gates

A pedestrian gate in Aloha usually lives next to a 6-foot cedar privacy fence, and it’s the gate you use every single day. That means it gets more wear than the driveway gate and it’s the first to sag. We build pedestrian gates with reinforced corner brackets and use posts that actually match the load, not whatever was cheapest at the lumberyard in 1987. A standard pedestrian gate install in Aloha runs $450-$1,200, including a new pressure-treated post set in gravel and a gate built to fit your opening.

Sliding Gates

Sliding gates work well on the flatter lots in Aloha, especially where the driveway slopes up toward the house and a swing gate would scrape or bind. The tradeoff is that sliding gates need a clean, level track, and that track collects dirt, fir needles, and wet leaves for six months of the year here. We install cantilever and V-track slides with enough clearance to keep running through the rainy season, not just the first month. Sliding gates run higher, usually $2,800-$7,500, because the track work and hardware cost more. For more on our installation approach, see our Gate Installation page.

How fast can you get to Aloha for a gate installation estimate?

We typically get to Aloha for an on-site measure within 1 to 3 business days. Since scheduling comes through our Portland office and we have crews working the Aloha area regularly, we can usually find a window that fits your day. Call (877) 610-2993 and we’ll set one up.

Do you warranty gate installations in Aloha?

Every gate installation in Aloha carries our 90-Day Done Right Promise in writing. If it isn’t done right, we make it right. That’s not a promotional phrase, it’s actually on the invoice. One call brings us back, and Hal doesn’t send someone else to handle his mistakes.

Gate Motor & Opener in Aloha

Gate motor and opener service in Aloha typically runs $150-$300 for diagnostic and minor repair, with full motor replacement landing between $900 and $2,200 depending on brand and whether we’re running new electrical to the gate. Most calls we get in the 97003 ZIP code involve older openers on 1980s and 1990s ranch homes that have finally succumbed to moisture intrusion or capacitor failure after decades of wet winters. We service nine major brands including Viking, Ghost Controls, DoorKing, and Elite, and we keep common boards and remotes in the truck so we are not ordering parts and making you wait a week.

Opener Diagnostic and Repair

The rainfall here, 37 to 40 inches a year, works its way into junction boxes over time and corrodes connections until the gate only opens halfway or ignores the remote entirely. We test the control board, the limit switches, and the safety loop in sequence so we’re replacing only what actually failed. Diagnostic and minor repair runs $150-$300. We also install fresh weather sealing on every electrical box we touch, because an opener that works in August and dies in February is almost always a moisture problem.

Motor Replacement

When a motor is truly burned out, we talk you through what a replacement honestly costs before any work starts. Adding a new opener to an existing gate adds $900-$2,200 depending on the brand and whether we’re running new electrical to the gate. We quote the exact number before we start, and that is the number on the invoice. For more on motor and opener service, see our Gate Motor & Opener page.

Why won’t my gate close in the winter?

Usually it’s moisture in the control board or limit switches that have drifted after the post shifted in the clay. The gate may close fine in dry weather, then stop short once damp gets into the electronics. We seal the housing, replace corroded components, and reset the limits so the cycle completes through the wet season.

Do you handle the power run and the safety edges on motorized gates?

Yes. Low-voltage wiring for safety edges, photo eyes, and loop detectors is part of every motorized gate job we do in Aloha. If you need a new 120-volt circuit run to the gate, we’ll bring in a licensed electrician and include that cost in your written quote before work starts. We don’t surprise you with a second bill later.

Gate Access Control in Aloha

Gate access control in Aloha, OR typically costs between $450 and $1,800 for a complete setup, depending on whether you’re adding a simple keypad to an existing opener or upgrading to a full phone-entry and video intercom system. Most Aloha homes we service are 1970s-1990s ranch and split-level builds, which means existing gate wiring is often older aluminum or thin-gauge copper that needs replacing before a modern access control panel can operate reliably. If you’re off Farmington Road, down near Butternut Creek, or anywhere in the 97003 ZIP code, we measure the existing wiring and quote the full job before touching anything.

Keypad Entry

A keypad mounted at the driveway post or on the gate itself is the most common access control upgrade we install in Aloha. Most of these homes were built before keypads were standard, so we’re adding them to existing swing gates that have been working fine mechanically but need secure entry for kids coming home from Aloha-Huber Park or for the landscaper on Thursdays. We wire keypads to work with your existing opener whenever possible, which saves you hundreds over a full opener replacement. Expect $200-$500 for a quality keypad installed and programmed.

Phone Entry

Phone entry systems are the step up when you don’t want to hand out codes to delivery drivers, home health aides, or the neighbor who waters plants while you’re away for a month. The system calls your cell phone when someone presses the call button at the gate, and you press a key to open it. Aloha’s hilly residential pockets, especially near the neighborhoods south of Butternut Creek, mean a good cellular phone-entry unit works better than a landline-dependent system that ties to a dying copper phone network. Plan on $600-$1,500 for a cellular phone entry system installed.

Card Reader Systems

Card readers aren’t just for apartment complexes in Aloha. We install them for homeowners with shop buildings behind the house, horse-property gates out toward Rockcreek, and shared private lanes where multiple homes share a common driveway. A standalone proximity card reader with a keypad backup and an electric strike runs $500-$1,200 on a typical Aloha gate. For more on access control options, see our Gate Access Control page.

How does your pricing compare to gate companies in Beaverton or Hillsboro?

We don’t pad quotes because of your zip code. Aloha’s unincorporated status doesn’t change our labor rate, and we don’t charge a trip fee inside the county. You’ll get a written price before any work begins, and we honor it. The 10% discount for seniors and veterans applies in Aloha the same as everywhere else we work.

Do you handle the electrical work for access control in Aloha?

Low-voltage wiring for keypads, card readers, phone entry, and intercom systems is part of every access control job we do in Aloha. If you need a new 120-volt circuit run to the gate to power an opener, we’ll bring in a licensed electrician and include that cost in your written quote before work starts. We don’t surprise you with a second bill later.

Gate Parts & Welding in Aloha

When a gate hinge tears loose or a post rots out at ground level, Aloha homeowners need two things: someone who answers the phone, and someone who fixes the gate without pretending the whole frame needs to be scrapped. Gatewood Fence & Gate handles both. We’re the shop that welds on site in your driveway, not out of a warehouse across town. Hal welds with the gate still in place so you can watch the work happen, and we quote every repair before we start.

Hinge Replacement

A gate sags in the hinge post, not in the middle. That’s where we start. In Aloha, the common culprit is a post that has shifted in the expansive clay, pulling the hinge screws loose and letting the gate drag. We replace hinges with heavy-gauge hardware and, when the post itself has moved, we address that first so the new hinges aren’t fighting the same problem six months later. Hinge replacement typically runs $180 to $340 depending on the post condition and gate weight.

Post Replacement

This is the big one in the 97003. Expansive clay soils swell every wet season and shrink every summer. A post set shallow, or set without gravel drainage, will heave and lean within a few winters. When we replace a post in Aloha, we dig deep enough to get below the worst of the movement zone and we set it so water moves away from the wood. Post replacement usually lands between $350 and $650 per post, with deeper digs and concrete work at the higher end. Fix the panel without the post and you’ll fix it twice. We’d rather do it once.

Custom Welding

Some fixes can’t come off a shelf. Maybe a metal gate got clipped by a delivery truck off Farmington Road and the frame is bent. Maybe you want a steel frame added behind an older wood gate to stop the sag for good. Hal welds on site, in your driveway, so the gate never leaves your property. Custom welding starts around $120 for small bracket and brace fixes and runs upward based on the scope. For more on our welding and parts service, see our Gate Parts & Welding page.

Can you weld a gate without removing it from the property?

Yes. In most cases, Hal welds on site with the gate still in your driveway or hanging in place. We don’t haul gates to an off-site shop unless it’s genuinely the better approach. On-site welding means you see the repair happen, and the gate doesn’t spend a week sitting in a lot while you wonder what’s going on.

What does the 90-Day Done Right Promise cover in Aloha?

If anything we repaired or welded fails within 90 days, we come back and make it right at no charge. The promise is written on every job, not buried in fine print, and it’s not pro-rated. It covers the work we did and the parts we installed. If something in the surrounding fence failed alongside our repair, we’ll tell you honestly whether it’s covered.

Brands We Service in Aloha

We are certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common boards, remotes, and safety sensors for Viking, Ghost Controls, and DoorKing locally, which means most Aloha repairs don’t wait on shipping. For the full list of brands and models we cover, see our brands page.

Pricing for Gate Repair in Aloha, OR

Neighborhoods We Serve in Aloha

We work throughout Aloha, and when you call, you’ll get a straight answer about when someone can be there. Same-day service is available for most repairs, depending on where we are in the county that morning.

• Cooper Mountain
• Butternut Creek
• Reedville
• Kinnaman
• Farmington Road corridor

Service Area - Cities Near Aloha

We serve Aloha directly and also work regularly in Rockcreek, OR, Cedar Mill, OR, Oak Hills, OR, Bethany, OR, and Beaverton, OR. Dispatch and scheduling are coordinated from our Portland office, but crews serve Aloha locally every week.

FAQs About Gate Repair in Aloha