Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Arcadia
Gate installation in Arcadia runs $1,800 to $9,500 for most jobs, and the work generally takes one to three days once materials are on hand. Hal Gatewood has been building and hanging gates since 2001, and his crew knows exactly what Arcadia’s luxury estates demand: heavy steel, ornate iron, underground operators, and hardware that holds up to Santa Ana winds. We’re not a franchise, we’re not a call center, and the person who quotes your gate is the same person who shows up to build it. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Arcadia’s Preferred Gate Installation Company
Most of what we fix in Arcadia was installed by somebody else, and a good chunk of it was never really built for this climate. We see gates that rack out of square every fall when the Santa Anas barrel down from the San Gabriel foothills, hinges that shear because nobody sized them for a 700-pound ornamental panel, and operators that grind themselves to death in the summer heat because the gear grease broke down and nobody noticed until the motor burned out.
Our crews are background-checked and uniformed, and Hal’s name is on the shop. That matters in Arcadia, where a gate isn’t a weekend project. It’s steel, concrete, low-voltage wiring, and a safety system that has to work every time. Call us at (877) 610-2993 and we’ll come measure, listen, and give you a written price before any work starts. No trip charge inside the county, and every job carries our 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No runaround.
Key takeaways:
- Locally owned and owner-operated since 2001, with a published address and license number
- We weld on site, so your gate never leaves your driveway
- Free second opinion on any written estimate, plus $40 off any repair over $200
- Permanent 10% discount for seniors and veterans
Our Gate Installation Services in Arcadia
Every gate we install in Arcadia is a custom job, whether it’s a modest pedestrian gate off a side yard or a full dual-swing motor court entry. Here’s how Gate Installation work breaks down for the homes we see most:
Driveway Gate
Arcadia’s newer luxury builds, especially north of Foothill Boulevard toward the foothills, are heavy on automated driveway gates. A typical custom driveway gate in Arcadia runs $3,200 to $9,500 installed, depending on width, weight, operator selection, and whether we’re running power to a new location. We set post footings 36 inches deep where wind load is a concern, which is most of Arcadia.
Pedestrian Gate
Pedestrian gates in Arcadia run $1,800 to $4,200 installed. That covers a welded steel frame, powder coat or paint finish, hardware, and a latch or lock system. We build these for the side yards and garden entries on older ranch homes in the lower streets, where a full driveway gate doesn’t always make sense. But the build standard is the same: welded joints, not bolted-together kits.
Sliding Gate
Sliding gates are common on Arcadia properties where the driveway slopes down from the street or where a swing gate would block the sidewalk approach. A motorized sliding gate in Arcadia typically runs $3,800 to $8,500. The catch here is wind. A long sliding panel acts like a sail in a Santa Ana event, and if the track and rollers aren’t sized right, you’ll get binding, bent rollers, and a motor that overloads and trips. We spec for that from the start.
Swing Gate
Swing gates, especially the dual or double gate configurations on Arcadia’s motor-court entries, are where most of the technical problems show up. A custom single swing gate runs $2,500 to $5,500; a dual ornamental iron swing gate runs $4,000 to $9,500 with automation. The gate sags in the hinge post, not in the middle, and that’s where we start – with post depth, post gauge, and hinge load ratings sized for the actual panel weight.
Double Gate
Double gates deserve their own line item in Arcadia because of how common they are on newer estates. Two heavy panels, two sets of hinges, an operator on each leaf or one master operator with a rod linkage. The custom-fabricated iron panels we see here often arrive with metric hardware specs and non-standard hinge pin diameters, which means a U.S.-sized replacement hinge or bushing won’t fit without modification. We machine what’s needed on site rather than forcing a mismatched part.
Security Gate
Security gates in Arcadia are a different animal than a simple driveway gate. These are gates integrated with intercoms, cameras, keypads, loop detectors, and sometimes vehicle detection. We install the gate and the access control as one system, not two separate projects. That means the wiring is planned before the concrete goes in, the operator is sized for the actual gate weight, and the safety edges and obstruction sensors are tested under load, not just on paper.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Arcadia
We’re certified to service and install nine major gate operator brands, and we keep local parts inventory for Arcadia jobs: Linear, DoorKing, Viking, and Ghost Controls among them. If your existing operator is a FAAC or a BFT or a LiftMaster, we work on those too. The point is we don’t push one brand and force your gate to fit it. We match the operator to the gate’s weight, duty cycle, and wind exposure. That’s why we stock gear assemblies, control boards, and safety edges for the brands most common in Arcadia, not just the ones easiest to order.
Common Gate Installation Problems We See in Arcadia Homes
Arcadia has a very specific set of gate failure modes. Here’s what we run into week after week:
- Santa Ana wind racking. Seasonal wind events funnel through the foothills corridors and rack heavy ornamental gate frames out of square. Hinge welds shear, panels misalign, and obstruction sensors trip repeatedly. The fix is deeper footings and heavier post sections, not a bigger motor.
- Overseas-fabricated iron with non-standard specs. Many custom gates on newer Arcadia estates were fabricated overseas and shipped in. Hinge pin diameters, mounting plate spacing, and weld quality vary wildly, and U.S. standard replacement parts often don’t fit without modification. This is rare a few miles west in Pasadena or east in Covina, but it’s the norm here.
- Summer heat breaking down operator grease. Hot, dry summers accelerate grease breakdown in gear assemblies on big custom iron gates. A gate that runs fine in June can be grinding by September, and the motor burns out a year later. We pull and re-grease gear assemblies before they fail, not after.
- Underground operator failures from poor drainage. Arcadia’s compacted foothill soils and clay-heavy lots hold water after rain. Underground gate operators installed without proper drainage sumps fill with water and short out. We set ours in crushed rock with a drain to daylight, because rebuilding a flooded operator box costs more than doing it right the first time.
Pricing for Gate Installation in Arcadia, CA
Here are honest ranges for Arcadia’s market, based on what we’ve actually quoted and built:
| Gate Type | Typical Arcadia Installed Price |
|---|---|
| Pedestrian gate | $1,800 - $4,200 |
| Single swing gate | $2,500 - $5,500 |
| Sliding gate (manual) | $2,800 - $5,000 |
| Sliding gate (motorized) | $3,800 - $8,500 |
| Double swing gate (with automation) | $4,000 - $9,500 |
What moves the price: gate width and weight, post depth, operator selection, whether we’re running new electrical, and whether the gate is a standard welded fabrication or a custom ornamental iron piece that needs shop time. Every quote is written, upfront, and agreed before any work begins. You will not get a different number at the door. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Arcadia
We work all over this part of the San Gabriel Valley. If you’re in Arcadia or one of the surrounding communities, we cover Mayflower Village, Sierra Madre, Monrovia, and Temple City. Same crew, same pricing, same 90-Day Done Right Promise. Call (877) 610-2993 and we’ll schedule a measure.
Serving Arcadia, CA - Our Local Coverage Area
We’re based in the Arcadia area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Arcadia
Because many of the ornate iron gates on Arcadia’s luxury estates were custom-fabricated overseas with metric hinge pin diameters, non-standard mounting plate spacing, and weld specs that don’t match U.S. standard replacement hardware. A standard hinge or roller from a catalog won’t fit without machining adapter bushings or re-drilling mounting holes. We handle that on site with welding and machining equipment on the truck. If your gate needs parts that don’t quite fit, call (877) 610-2993 and we’ll make them fit right.
Yes. We install underground operators regularly in Arcadia, especially on motor-court entries where an above-ground arm would look wrong. The critical part is drainage. Arcadia’s clay-heavy foothill soils hold water, and an underground operator box without a proper crushed-rock sump and drain will fill with water and short out. We set ours with drainage to daylight and size the operator for the gate’s actual weight plus a safety margin for wind load. Expect $2,200 to $4,800 for the underground operator portion of an Arcadia installation. Call (877) 610-2993 for a written quote.
For a heavy dual ornamental iron swing gate in Arcadia, we typically spec a FAAC 844 or a Viking equivalent sized for at least 800 pounds per leaf, paired with a LiftMaster loop detector and safety edges on both leaves. The operator matters less than the post and hinge setup underneath it. If the hinge posts are undersized or the footings are shallow, no operator will fix the racking that Santa Ana winds cause. We start with the structure, then match the operator to it. Call (877) 610-2993 and we’ll measure your gate and give you a straight answer.
Santa Ana winds funnel through the foothills corridors at the base of the San Gabriels and hit Arcadia’s heavy ornamental gates with enough force to rack frames out of square, shear hinge welds, and trip obstruction sensors repeatedly. The fix is built into the installation: 36-inch-deep post footings, heavier post gauge, hinge load ratings matched to actual panel weight, and an operator with enough torque reserve to move the gate in a 50 mph gust. A gate installed to coastal L.A. standards will fail here within a couple of seasons. Call (877) 610-2993 if your gate is already showing wind damage.
Yes, and this is standard practice for us on Arcadia installations. We run the low-voltage wiring for intercom, keypad, camera, and loop detectors at the same time we set the gate posts and operator, so you’re not trenching twice. On a recent job near Highland Oaks, we paired a FAAC 844 operator with a LiftMaster loop detector and a door intercom tied to the homeowner’s existing camera system. One trench, one crew, one warranty. Call (877) 610-2993 to talk through what you want at your entry.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Arcadia since 2001.