Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Glendale
Gate access control in Glendale usually falls into one of three jobs: keypad entry, a video intercom, or a phone-entry system tied to an existing automated gate. A straightforward keypad replacement on a flatland home in 91205 runs $350-$650, while a full retrofit with video intercom and smart access on a hillside property in 91208 typically lands between $1,800 and $3,200. Hal Gatewood has been fixing and installing gate systems since 2001, and when you call (877) 610-2993, a live person answers – not a voicemail, not a call center. We show up in Glendale the same day for access control failures that leave you locked out or stuck outside your own driveway.
We know the difference between the flatland bungalows of Adams Hill and the steep driveways of Chevy Chase Canyon. The gate and the operator behave differently in each, and so does the access control. That’s why we stock parts for DoorKing, Viking, and LiftMaster operators locally and carry keypads and intercoms that survive Glendale’s October Santa Ana season without quitting.
Why Gatewood Fence & Gate Is Glendale’s Preferred Gate Access Control Company
Hal’s name is on the shop, the shop address is published, and the license number is there for anyone who wants to look it up. That is unusual in the gate access control trade, and Glendale homeowners notice. We get calls from people who were quoted one price over the phone by some national outfit, then watched the number grow at the door. We quote the job before we start. You know the number before we touch a wire.
Our Gate Access Control team has been out to Glendale homes enough to know the patterns. A 1928 Spanish Colonial Revival in Rossmoyne has original masonry pillars that were poured decades before anyone imagined an automated gate. A hillside home in Verdugo Woodlands has a gate that weighs three times what the operator was rated for. We start with what’s actually there, not a catalog.
Every job carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal back. No runaround. Beyond that, we answer the phone 24/7, and senior and veteran homeowners in Glendale get a permanent 10% discount. A $40 discount applies to any repair over $200, and there’s no trip charge inside LA County. We also offer a free second opinion on any written estimate you’ve received from another company.
Our Gate Access Control Services in Glendale
We handle the access side of the gate: the keypad, the intercom, the phone entry box, the card reader, the smart app. We also handle what happens when the system tells the gate to move and the gate can’t. In Glendale, those two jobs are often the same call.
Keypad Entry
A keypad replacement in Glendale runs $350-$650 for a standard wired unit, and $500-$900 for a wireless or weather-sealed model built for hillside exposure. We install and program keypads on existing operators from DoorKing, Viking, LiftMaster, and Elite, and we mount them on stucco pillars in a way that doesn’t crack the original masonry. Glendale flatland homes built in the 1920s and 1930s often need a custom bracket to get the keypad off a rounded pillar face, and we build those in the field.
Video Intercom
Video intercom systems in Glendale run $1,200-$2,800 installed depending on whether we’re adding a single-doorbell-style camera station or a full multi-tenant panel with inside monitors. This is the single most requested access control upgrade in Glendale’s Spanish-style neighborhoods, where front doors sit far from the street and the driveway gate is a long walk from the kitchen. You see who’s at the gate from your phone or a wall-mounted monitor before deciding to open anything.
Phone Entry
Phone entry systems for Glendale homes typically run $800-$1,900 installed. A visitor punches your code or scrolls to your name, the panel calls your cell or landline, and you press a button to open the gate. We service existing phone entry boxes from DoorKing and Viking, and we replace obsolete boards rather than telling you to buy a whole new system when the old one just needs one part.
Card Reader and Smart Access
For Glendale homeowners with caregivers, housekeepers, contractors, or multiple family vehicles, a card reader or smart access app solves the problem of who has a key and who doesn’t. Card readers run $450-$900 added to an existing system. Smart access retrofits – where your existing gate opens from a phone app instead of just a remote – run $500-$1,200 depending on operator age. In Chevy Chase Canyon and Verdugo Woodlands, we pair these with operators actually rated for the gate weight, because the smartest keypad in the world doesn’t help when the motor underneath it is fried.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Glendale
We service and install DoorKing, Viking, and Ghost Controls systems in Glendale, along with LiftMaster, FAAC, BFT, Linear, Elite, and Mighty Mule. More importantly, we keep the parts that Glendale’s older gates actually need – control boards for DoorKing 9150s and Viking swing operators, safety photocells, loop detectors, keypad overlays, and wireless receivers. If your access control system went dark last week and you’ve been leaving the gate propped open with a cinder block, call us. We’ll know which board it needs by the fifth word of your description.
Common Gate Access Control Problems We See in Glendale Homes
- Undersized operators on heavy decorative gates in hillside ZIP codes. A 900-lb ornamental iron gate on a 400-lb-rated operator is the single most common failure we find in 91207 and 91208. The motor burns out in 2-3 years, and the keypad or intercom gets blamed when the real problem is the operator underneath.
- Original 1920s-1940s masonry pillars cracking under automated swing gate loads. The flatland neighborhoods of 91201-91206 are full of pillars poured before automation existed. Gears and hinges transfer force into the pillar, the pillar shifts, the gate sags, and the keypad eventually stops engaging the latch because nothing lines up anymore.
- Santa Ana winds disabling keypads and safety edges every fall. October and November in Glendale mean wind funneling down from the Verdugo Mountains. Gates get slammed, latch posts get bent, safety photocells get knocked out of alignment, and the access control system faults out. We brace the gate, align the sensors, and repair the hinge post so it doesn’t happen again next week.
- Obsolete control boards on older DoorKing and Viking systems. Many Glendale gates were installed 15-25 years ago, and the boards inside are no longer made. We stock replacements and retrofits that work with the existing motor, wiring, and keypad, so you’re not forced into a full system replacement because one board failed.
Pricing for Gate Access Control in Glendale, CA
A straightforward keypad replacement on a flatland Glendale home runs $350-$650. A phone entry system runs $800-$1,900. A video intercom runs $1,200-$2,800. A full smart access retrofit on an older hillside gate with a new commercial-rated operator lands between $2,500 and $4,500, and that’s the number that fixes the burnout problem instead of just replacing the burned-out part.
What moves the number in Glendale is the gate itself. A 1928 originals door gate with decorative scrollwork and 900 lbs of iron needs a different operator than a 250-lb aluminum pedestrian gate. A sloped driveway in 91208 adds load every time the gate opens. A flat driveway in 91205 doesn’t. We measure the gate, we test the operator, and we tell you the exact price before we start. Estimates are free. The price is quoted and agreed before any work begins – always. Call (877) 610-2993 and Hal will walk you through it over the phone in ten minutes.
We Also Serve Cities Near Glendale
Our Gate Access Control in Glendale service covers the full city, and we regularly work just over the border in Burbank, La Cañada Flintridge, Echo Park, and Silver Lake. If you’re in one of those neighborhoods and your gate is misbehaving, call the same number – (877) 610-2993 – and we’ll get you on the schedule. Dispatch and scheduling are coordinated from our Los Angeles office, and crews serve Glendale locally.
Serving Glendale, CA - Our Local Coverage Area
We’re based in the Glendale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Glendale
No. It means the operator is undersized for the gate weight. In Glendale’s 91207 and 91208 hillside zones, we routinely find 800-1,200 lb decorative iron gates running on 400-lb-rated residential operators. The motor burns out because it’s working three times harder than it was designed to, and the slope of the driveway adds load on every cycle. The fix is a commercial-rated operator on a residential permit, sized for the actual gate weight. Call (877) 610-2993 and we’ll measure the gate and give you a straight answer on what it needs.
Yes – if you’re in the Wildland Urban Interface zones of 91207 or 91208, fire evacuation access codes require an emergency-release mechanism that fire crews can access. A Knox Box mounted on or near the gate lets Glendale Fire open the gate without waiting for you. We check for one on every hillside repair. If it’s missing, we add it as part of the job. It’s a code compliance item, not an upsell.
The problem is in the hinge post, not the keypad. Original 1920s-1940s masonry pillars in Glendale’s flatland neighborhoods crack and shift under automated gate loads, and the whole gate drops. The keypad may still send the signal, but the gate can’t complete the cycle. We reinforce the post, re-hang the gate, and realign the latch before touching the electronics. Then the keypad works like it’s supposed to.
Yes. We do it regularly in Glendale, and we’re particular about not butchering the ironwork. That means surface-mounting the keypad on a bracket that fits the pillar profile, running new wiring through conduit that follows the existing line, and matching the intercom placement to the gate’s original hardware spacing. For ornate gates in Glendale’s Armenian-American neighborhoods where the ironwork is elaborate, we’re careful with the mounting so the retrofit doesn’t look like an afterthought. Call (877) 610-2993 for a free quote.
Santa Ana winds are the answer. Every October and November, wind funneled down from the Verdugo Mountains slams gates hard enough to bend latch posts, strip hinge anchors, and knock safety photocells out of alignment. The operator itself is usually fine. The failure is mechanical, and it disables the access control. We reinforce the gate and realign the sensors, which stops the seasonal failures rather than patching them.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Glendale since 2001.