FAAC Gate Access Control Nationwide | Gatewood Fence & Gate

FAAC Gate Access Control in Los Angeles: What to Know First

FAAC gate access control repair in Los Angeles typically runs $180 to $600 depending on whether the board is salvageable, the motor is burned, or the whole operator needs replacing. Most jobs get diagnosed same day and fixed within 48 hours once parts are in hand. We are an independent FAAC service provider, which means we fix your equipment rather than pushing a brand-new system on you.

Call (877) 610-2993

This page is for the homeowner who has a FAAC gate that stopped opening when they pressed the remote, keyed the code, or buzzed somebody in from the house. The phone number is (877) 610-2993. A live person answers, 24 hours a day, seven days a week. No voicemail, no call center three states away, just someone who works on these gates every week.

How FAAC Products Fail, and How We Fix Them

FAAC builds a solid operator, but every brand has its known weak points. Here is what we actually see on Los Angeles gates, not what the spec sheet claims.

• FAAC 400 and 402 operator boards losing the remote codes. The memory chip on these boards sits right where the afternoon sun bakes, and in the San Fernando Valley that heat eventually corrupts the stored transmitter codes. The gate still opens with the keypad, but every remote goes dead. We resolder the chip or swap in a tested board and reprogram the remotes, same day.
• FAAC 750 and 760 swing arm operators with photocell faults. Many of these were installed before safety edges were strictly required in Los Angeles residential gate codes, so the photocell is doing all the safety work alone. When a single errant reflection or a dying cell trips across, the gate refuses to close. We trace the loop and replace the photocell with an OEM part so the voltage logic matches what the board expects.
• Keypad drift on FAAC 391 and 844 entry systems. The silicone button pads wear unevenly from constant direct sun, and the number 1 and 9 keys stop registering. The code is not wrong, the keypad physically is not sending digits. We replace the keypad assembly and often relocate it to a shaded wall face so the next one lasts longer in our local climate.
• Solenoid lock on FAAC 400 models not releasing. The plunger gets dust and dried grease in it, especially on hillside properties in Studio City and the Hollywood Hills where dry canyon air carries a lot of particulate. The actuator is cheap and we stock the common FAAC versions, so this is usually a 30-minute fix in the driveway.
• Phone entry modules on FAAC 844 ER failing after a power surge. The on-board transformer is undersized for the dirty power you get in older Los Angeles neighborhoods with overloaded substations. The symptom is a dead display and no dial tone at the panel. We install a separate surge-rated transformer after replacing the board, so the new one does not get fried by the same DWP spike.

Our FAAC Gate Access Control Process

Here is what a FAAC access control call looks like when you call Gatewood Fence & Gate.

1. 1
   You call (877) 610-2993. Hal or the person who answers trips a note about your address and the symptom you are describing. We set a window we can actually keep.
2. 2
   We diagnose on site. We do not guess over the phone. The person who shows up opens the operator, checks the board voltage and the accessory wiring, and tells you honestly if the part is fine and the real problem is a stripped gear or a bad ground.
3. 3
   We price it right there. You get a written quote before any work starts, and that price does not change because the job “got harder” halfway through. If we find something additional, we show you and get your okay first.
4. 4
   We decide OEM or quality aftermarket, together. If an OEM FAAC part is the only one that will last or needs to keep a warranty intact, we use it. If an aftermarket photocell or keypad runs the same board logic for half the price and holds up the same, we tell you that too. We are not marking up parts by a multiplier.
5. 5
   We replace the part, rewire, and test. That means six open and close cycles with a vehicle in the path to confirm the safety edges and photocells are doing their job, not just one press of the remote.
6. 6
   We hand you the 90-Day Done Right Promise in writing. If it fails or acts up inside 90 days, one call brings the same person back. No arguing, no “it must have been a different problem.”

What FAAC Gate Access Control Costs in Los Angeles

Every gate is different, but here are the ranges we honestly see on FAAC jobs around Los Angeles.

• FAAC remote or keypad programming: $90 to $150 when the board and existing remotes are functional.
• Photocell or safety edge replacement: $160 to $300, including matching the new cell to the board voltage.
• Keypad assembly replacement: $180 to $320, depending on the FAAC model and whether we need to relocate the shroud.
• Control board swap (FAAC 400, 402, 750): $320 to $600, including rolling the existing remotes and limits forward.
• Full operator replacement with phone entry or card reader: $2,800 to $6,500 for a twin swing gate with motor, arms, entrapment protection, and the access panel. This is a scheduled job, not a same-day repair.

What moves the price is whether the operator is AC or DC powered, how many keypads and readers are hung on the loop, and whether the previous installer did the wiring so badly that we have to pull fresh conductors. You will know that before the first wrench turns. Estimates are free, and there is no trip charge inside Los Angeles County. Call (877) 610-2993 for a written number.

Why Los Angeles Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood grew up in the San Fernando Valley, not far from the old Hansen Dam recreation area, and he has been working gates and fences around Los Angeles since 2001. He did his fundamentals at Los Angeles Trade-Technical College downtown, then spent years in the field learning what the classroom never covers, like why a gate that swung fine in February starts dragging every August when the ground shifts.

Hal is the guy neighbors call when a previous installer left behind stripped hinges, wrong-gauge hardware, or a motor wired so badly it trips the breaker every other week. Sorting out that kind of mess is honestly what he is best at, and on a FAAC job that means the person at your gate knows the difference between a 400 board revision and a 750, not just “a gate motor.”

We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has mixed brands across the front and side gates, one visit handles both. And every job carries the 90-Day Done Right Promise in writing, not buried in fine print. The name is on the shop, and the shop is down the road, that is the oldest accountability there is.

FAQs