Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Fullerton
Gate parts and welding in Fullerton usually means one of two jobs: either a hinge post has rusted through on a 1960s wrought iron gate, or a slide gate on a Sunny Hills slope has thrown its track. We handle both, and we do it without hauling your gate to some far-off shop. Our crew welds on site, in your driveway, so you’re not paying freight on a 400-pound iron panel. Call (877) 610-2993 and you’ll get a live person, not a voicemail. We’ve been fixing gates since 2001, and Fullerton’s older housing stock is exactly the kind of work we’re built for.
Why Gatewood Fence & Gate Is Fullerton’s Preferred Gate Parts & Welding Company
Fullerton has some of the oldest housing stock in Orange County. That means gates here fail differently than they do in newer cities like Buena Park or La Palma. A 1968 ranch home off Euclid or a hillside custom place in 92835 has hardware that was installed before modern safety photocells existed, before stainless steel track anchoring was common, before anyone thought about Santa Ana wind loads on a 12-foot swing panel. We know those failure points because we see them weekly. The name on the shop is Hal Gatewood’s name, and he has been at it since 2001. A live person answers the phone 24 hours a day, seven days a week. When a Fullerton customer calls about a gate dragging on the driveway, the person who answers understands what that means: a hinge post has gone soft underground, or the bottom rail is corroded through. We don’t read from a script.
Every job carries the 90-Day Done Right Promise, stamped in writing. If it’s not done right, one call brings us back. No runaround, no fine print. We also offer $40 off any repair over $200, no trip charge inside the county, and a free second opinion on any written estimate you’ve gotten from another company. Seniors and veterans get a permanent 10% discount. These aren’t gimmicks. They’re how we do business in Fullerton.
Our Gate Parts & Welding Services in Fullerton
Here’s what we actually do when someone in Fullerton calls us about a failing gate. These are the four jobs that make up most of our work in this city.
Hinge Replacement
Hinge pins on 50-year-old wrought iron gates in Fullerton wear into ovals, not circles. That’s why the gate sags and scrapes the concrete. We cut out the old hinge, weld in a new barrel hinge or heavy-duty bearing hinge, and align the panel so it swings clean. On gates in the 92832 and 92833 ranch tracts, we usually recommend greasable hinges, because the inland heat dries out standard ones fast. A hinge replacement in Fullerton typically runs $180-$340 depending on gate weight and whether the post needs reinforcing.
Post Replacement
The hinge post is where Fullerton gates fail first. Moisture wicks up from poorly drained footing, the steel rusts at ground level, and the whole gate leans. We dig out the old footing, set a new post deeper with proper drainage gravel, weld the gate back onto it, and you’re done. In the 92835 hillside areas, we set posts with extra concrete depth because the sloped grade puts more lateral load on the post when the gate swings downhill. A post replacement with new footing in Fullerton generally runs $450-$850.
Rail Repair
Bottom rails on old Fullerton gates rot from the inside out. You can’t see it until the gate droops. We cut out the corroded section, weld in a new steel rail, and if the damage is extensive, we reinforce the entire bottom chord with a sleeve. On slide gates, rail repair often means more than the visible track. The Sunny Hills sloped aprons heave and crack, pulling the track out of alignment. We anchor the track with stainless steel fasteners so it stays put. Rail repair in Fullerton typically runs $250-$600 depending on how much steel needs replacing.
Custom Welding
Sometimes the gate is worth saving even when a chunk of it is gone. We weld in new pickets, rebuild rotted bottom rails, fabricate new gate frames from scratch when needed, and repair broken welds on ornamental scrollwork. If you have a 1960s Fullerton gate with the original scrollwork, we’d rather repair it than replace it. A new steel panel won’t match the patina or the design. Custom welding work in Fullerton generally starts around $150 for small repairs and runs up to $900+ for major structural rebuilding. We quote the price before we start, and it doesn’t change at the door.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Fullerton
We’re certified to service nine major gate brands, and in Fullerton we see a lot of older Linear and DoorKing operators on 1970s and 1980s installs, plus Ghost Controls on more recent retrofit jobs. We keep a stock of common parts for these brands on the truck, so we’re not driving back and forth to a supply house while your gate hangs open. If your operator board is fried from a decade of Fullerton inland heat, we can usually swap it same day. That goes for Linear, DoorKing, Ghost Controls, and the others we service.
Common Gate Parts & Welding Problems We See in Fullerton Homes
- Ground-contact weld corrosion on 1950s and 1960s wrought iron gates. The original welds at the bottom rail and hinge post were never sealed against moisture. Decades of drip irrigation and rain wicking up from the footing turn them to rust powder. The gate looks fine up top, but the bottom is about to let go.
- Slope-related track heaving in Sunny Hills (92835). The concrete aprons on hillside driveways expand and contract with temperature swings, cracking standard slide-gate tracks. We see this constantly in north Fullerton. The fix is stainless steel anchoring and regular realignment, not just tightening bolts.
- Santa Ana wind damage to swing gates. Central and west Fullerton get hammered by Santa Ana wind events funneling through inland corridors. A 12-foot swing panel acts like a sail. Hinge posts bend, rack and pinion drives on slide gates misalign, and sensors get knocked out of whack.
- Obsolete control boards on 1970s and 1980s operators. Fullerton’s inland summer heat bakes circuit boards. If your operator is old enough to have a mechanical limit switch, parts are getting hard to find. We can retrofit modern boards and safety components onto old gate frames without replacing the whole system.
Pricing for Gate Parts & Welding in Fullerton, CA
We give the price before we start, and it doesn’t change at the door. Here are the ranges you’ll see in Fullerton for common jobs:
- Hinge replacement: $180-$340
- Post replacement with new footing: $450-$850
- Bottom rail repair (cut and weld): $250-$600
- Custom welding, small picket or scroll repair: $150-$400
- Custom welding, major structural rebuild: $600-$900+
- Gate rollers and alignment: $120-$300
- Safety photocell and loop detector retrofit: $350-$750
What moves the price in Fullerton is gate weight, access to the footing, and whether we’re repairing a flat 92833 driveway or a graded 92835 hillside. A 400-pound wrought iron panel on a slope takes more labor than a 200-pound aluminum gate on flat ground. We don’t charge a trip fee inside the county. Call (877) 610-2993 and we’ll give you an exact quote. Estimates are free.
We Also Serve Cities Near Fullerton
Our Gate Parts & Welding crew covers Fullerton and the surrounding area, so if you’re in Anaheim, La Habra, Placentia, or La Habra Heights, we’ll come to you too. Same live phone answer, same 90-Day Promise, same on-site welding. That’s the whole point of being local.
Serving Fullerton, CA - Our Local Coverage Area
We’re based in the Fullerton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Fullerton
Most of the time we can weld it straight. The sag is almost always in the hinge post or the bottom rail, not the gate panel itself. We cut out the bad steel, weld in new material, reset the post if needed, and the gate swings level again. Replacement only makes sense when the panel is more rust than steel. Call (877) 610-2993 and we’ll tell you which one you have, free.
Usually both. The sloped apron in 92835 puts extra strain on the operator’s limit calibration, and if the track has heaved even a quarter inch, the gate binds and the operator overshoots trying to compensate. We weld in stainless steel track anchors to stop the heave, then recalibrate the travel limits. A new operator without fixing the track won’t solve it. Call (877) 610-2993 and we’ll come take a look.
In most cases, yes, you replace the post but not the gate. We cut the gate off clean, dig out the old footing, set a new post deeper with drainage gravel so the same thing doesn’t happen again, and weld the gate back on. This is one of the most common jobs we do in Fullerton’s 92832 and 92833 ranch tracts. If the post is only surface-rusted and still structurally sound, we can grind it down, reinforce it, and weld on a collar instead. You’ll know before we touch anything.
Yes, and this is a job we do regularly. Older operators in Fullerton often have no safety reverse system and no vehicle detection. We can add external photocells, a loop detector, and a modern control board that brings the system up to current safety standards. We don’t leave a gate that can close on a car or a kid. The retrofit is cheaper than a full operator replacement. Call (877) 610-2993 for a quote.
In Fullerton, it’s usually the rail. Santa Ana winds push the gate sideways, which bends the rail brackets and knocks the track out of alignment. The rollers get blamed because they’re the part that squeals. We straighten the rail, weld reinforcement brackets if the wind load keeps happening, and replace rollers only if they’re actually worn. Call (877) 610-2993 and we’ll diagnose it properly.
If your gate is sagging, scraping, binding, or just not closing right, call us at (877) 610-2993. You’ll get a live person, an honest answer, and if we come out, the price is set before we start. Serving Fullerton since day one, one gate at a time.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate. Hal has been fixing gates and fences since 2001 and still answers the phone himself.